razer kishi adaptor for pixel 5 with google case by 3d models

Remix for the Pixel 5 in the Google case. ...Sides bumped out by 1mm.

I bought a Razer Kishi gamepad for my samsung s10e but there are no adaptor for my phone (and case) so this it. It's a basic to hold the phone without movement. ... The latest version mark4 can stay in the gamepad when closed.

remix from https://www.thingiverse.com/thing:5978960/ spacer for the razer kishi v1 with google pixel 6 and slim case (especially this one: https://amzn.eu/d/3Lie7FM) just the usb-c side because the other side was pretty secure but the usb-c side...

Drop In replacement for the left side of the Razer Kishi Android Gamepad padding to fit the Google Pixel 6. Because the camera bump of the Google Pixel 6 is to near to the top of the phone, the rubberpadding doesn't fit. ...So I designed this...

... clips for printing in PLA. ... Fits well, though the clips may break if you keep removing it and clipping back in. Tested on Oneplus 7 Pro with case. Added cut out for top phone speaker which is normally covered with original Kishi rubber grip.

______________________________________________ This brace adds side support to the device, filling the gaps present when ujsing the Kishi without the rubber spacers, effectively allowing the Pixel 4a with DBrand case to slot into the device while...

Only the one file is needed for either side of the Kishi as the slots on each side are the same dimensions. This brace adds side support to the device, filling the gaps present when ujsing the Kishi without the rubber spacers, effectively allowing...

Razer Kishi adapter for Samsung S21 with Spigen Thin Fit case. Recommend TPU since it is flexible and installs like the stock cushions. Also tested with ABS but you will need to cut off the end tabs. No supports needed. Print upright and use whatever...

Razer Kishi adapter for Samsung S21 with Spigen Thin Fit case. Recommend TPU since it is flexible and installs like the stock cushions. Also tested with ABS but you will need to cut off the end tabs. No supports needed. Print upright and use...

Google Pixel 5 Case ONLY FOR GOOGLE PIXEL 5

Google Pixel 5 Case

Simple Case for the Google Pixel 5.

Pixel 5 case. ...Printed on Prusa MK3S with SainSmart TPU using PrusaSlicer.

Designed a protective case for my Pixel 5. Requires 6x 6mm hex screws. Ideally printed in PC-ABS, but polycarbonate, or HIPS depending on the type of impact resistance preferred. ... Adjustment required for shrinkage of the material to be used, refer...

... this gamepad. ...I've made this crappy remix that works. It has added grips to improve handling of a phone so it has less chance of accidentally slipping out. Not optimized for modding, just did whatever I could asap since I still can't model myself.

Case for the Google Pixel 5 phone with an hexagonal pattern on the backside of the phone. ...Based on the excellent Pixel 5 case by p3t3rp4nd4 : https://www.prusaprinters.org/prints/43740-google-pixel-5-case

Case for the Google Pixel 5 phone with an hexagonal pattern on the backside of the phone. Based on the excellent Pixel 5 case by p3t3rp4nd4 : https://www.prusaprinters.org/prints/43740-google-pixel-5-case

... to protect but still allow pushing. Supports added to bottom usb charging slot to help avoid curling during print. Fusion 360 shared link: https://a360.co/3bOvKEO Fusion 360 project also includes Pixel 5 shape and minimal case as well. ...

Print instructionsMy print: MK2.5S 0.6 mm nozzle, generic TPE, 240C no bed heat 5 perimeters (with 0.6 nozzle) large brim and glue stick to hold down on smooth surface bed. Load both Pixel_5_cover.stl and Pixel_5_brim.stl. Set 10 or more perimeters...

 For this print I was inspired by https://www.printables.com/model/85886-pixel-6-pro-case Pixel 6 case. ... Like JoshCraft3D, I used zero top and bottom layers in order to expose Prusaslicer's hexagonal infill, and turned on fuzzy skin to give the sides...

Fusion 360 project also includes Pixel 5 shape and full flexible cover as well. Print instructionsMy print: MK2.5S 0.6 mm nozzle, filaments.ca ecoTough PLA , 220 °C switched to 210 °C at around 1mm height to avoid stringing. Bed 60 °C 5 perimeters...

... drone as it was intended. I'm waiting for the Pixel 7 to be released and I'll make an updated version once I get it. For now, I'm sticking to the Pixel 5. ... The notch-less end of the case is there to indicate the lower-right corner of the case.

... for an enhanced listening experience. ...The ideal solution would be a custom-made Junglecat case designed exclusively for the Google Pixel 3A model, with a unique modification feature that seamlessly integrates with the Jack Audio Cable technology.

This slightly odd case is designed to fit the Google Pixel 4a (4g) phone with either a think silicone case, or a thicker usually clear TPU case.It uses a right angle TOPK right angle magnetic USB cable (gen 1, not gen2 or 3). ...The end of the cable is...

Check out this simple brodit mount for a Pixel 3 (non XL) with case (Spigen Liquid Crystal). The phone can be easily swiveled inside the mount, making it easy to insert or remove. ... ...

Simple brodit mount for a Pixel 3 (non XL) with case (Spigen Liquid Crystal). The phone can be wiggled a slight bit inside, because I wanted it to be easy to insert or remove....

Google Pixel 5 holder which is made to fit the phone with a Google case on. Securely holds your phone with a charging port cutout at the bottom. ... Use a high temperature filament if you plan on mounting this to the dash of your car because PLA will...

... link: https://a360.co/3bOvKEO Fusion 360 share link allows downloading in fusion 360, Inventor, IGES, SAT, SMT, STEP, DWG, DXF, STL, FBX, SketchUp and OBJ formats. Fusion 360 project also includes Pixel 5 shape and full flexible cover as well.

... a little bit. ... https://www.thingiverse.com/thing:4688933 There are two uploads for the case, itself. One has a block added for easy alignment to center in Cura for Z Hop -- If you watch the video, you will understand. ... Thanks for checking it out!

https://www.thingiverse.com/thing:4688933There are two uploads for the case, itself. ...One has a block added for easy alignment to center in Cura for Z Hop -- If you watch the video, you will understand.Thanks for checking it out!Print...