raven 3d model

Cheers. Print Settings Printer: D-Bot Rafts: No Supports: No Infill: 20% Rectlinear Filament: DASFILAMENT PETG Trans Blue / Trans Green Notes: You need: a heatbed because of the big surface of the model A coolerfan for the threads Category:...

### Bridge style cards (58mm x 88mm) * `codeandmake.com_Quick_Draw_Card_Dispenser_v1.0_58x88_Single_Open.stl` * `codeandmake.com_Quick_Draw_Card_Dispenser_v1.0_58x88_Single_Covered.stl` *...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_resolution = 8 custom_right_port_corner_radius = 5 custom_back_camera_x_position = 0...

twisting both wire pairs reduces possible crosstalk and possible issues from it. there are holes for zipties after each dragchain, use it to secure the wires but leave some wiggle room for the wires inside the dragchain, if they are to tight...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

unless you have a special edition like a Porsche, Mercedes, or older Audi, VW, or BMW model, which is what I have. For most of these special editions, the original push bar won't fit. I found a design on Thingiverse called *Klein-laui* and tested...

OK, this isn't a model but rather a gcode script to facilitate automated cold pulls to clear out your nozzle. I use it all the time on my Ender 3 and thought others might get some good use from it as well. **What is a cold pull?** A cold pull is...

Previous model description: I hooked up a 1400mah battery and drove this home from my local park around 500-600 meters with no heat issues affecting the PLA print. I have used this around the house quite a bit with the camera, and it works well. The...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8 custom_top_port_corner_radius...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

When/if I model it, I will put it on here.Have any modification requests? Contact me in the comments. I am active on Thingiverse.If you want to modify the design yourself, I can try to provide the original Tinkercad schematic on request.Update: Added...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 1 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

The parts I used: * 30mm M3 flat screws: https://smile.amazon.com/gp/product/B07NWL5HK3 * 16mm M3 hex screws: https://smile.amazon.com/gp/product/B014OO5KQG * M3 nylon lock nuts: https://smile.amazon.com/gp/product/B07GNXDQJZ * 20mm CR-10 springs:...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

On my version, I suggest that you start with 4 seeds in each of the 12 pits (print 4 copies of the 12 seed model and then separate them using nail clippers or small scissors). Increase the number of seeds in each pit progressively to increase the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

It is possible that a future will make and upload a model of that piece. In the meantime, if anyone knows where to get suitable pads, please let me know. As I was saying, I started to hang them on the screw. Since the surface of the screw with the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

The bands were modeled separately so they wouldn't require supports and be stronger. I printed them on their sides and used a brim as they had less surface area. They will have to be glued. The main body and battery compartment required supports. I...

Update 01.04.2023 A friend i have made through the Neo Community have discovered that the clearance might not the good with the standart Neo, because the belt housing on the left stick out further, he have provided the file named...

(I have included a model with logo, and one without)Assembly Instructions:Print the box and two clipsInsert bowtie shaped post on clip in to corresponding hole on box, then rotate until the push-clip lines up with the hole.Push the push-clip in to...

However another person created this and the subsequent prusaslicer ini file. however I am not quite knowledgeable enough with gcode and prusaslicer to make the necessary adjustments to it to make it work on the mini (plus I prefer to do it directly...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_top_port_corner_resolution = 8 custom_back_camera_x_position = 0...

My original plan was to also model a strap clip for the bottom of the mount, but I found that it was unnecessary, as the entire thing can be attached directly to the head strap and head pad with a velcro strap. I used a couple of long velcro cable...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

My prototype box had a problem in which the combination could be guessed by feel due to the slack in the model. This problem was fixed with a number of features that make guessing the combination by feel very difficult. As an additional precaution, I...