ratrig vcore 3 3d models

Ratrig LAN adapter (fixed) for standard Keystone/RJ45 I had problems with the Ratrig Vcore LAN adapter. No standard keystone did fit in (had different Manufacturers to test). Derived from the original 3D File provided by Ratrig, the Part is...

duct for hemera e3d on v-core 3, 13.2°

 I like that the spacers are not used and that it prints vertically so the prints are much smoother.Original DescriptionThese are the XY Joiners made by Vector3Dhttps://github.com/AdamV3D/V-Core-3-Vector3DEdition/tree/main/Printer combined with the...

 This is a two piece holder where the front cover is bolted over the power inlet and holds it in place when plugging/unplugging it.This goes between the two upright rails in the rear of a V-Core 3.1.  I designed it to only attach to the outer most...

A modified version of the enclosure 2.0 front panel is in the works.  This modification is technically compatible with a regular, unenclosed V-Core 3.1, although you will have to move the front upper 3030 extrusion down to clear the...

This is a bed corner piece that acts as a stopper to slide your spring steel sheets against.When assembling my V-Core 3 I instantly noticed that it would be almost impossible to properly place the steel sheet on the magnet as there is nothing to...

<p>After fitting a drag chain to my printer I couldn't find a suitable ending to fit between the Orbiter extruder and the dual fan super sniffles mod so I made this one. ...It is a tight fit to get all the wires behind the orbiter but it does tidy it up...

I ran wires inside my rear 3030, therefore the original rear shelf would not work. I made sure to leave room for the belts in the rear, this won't rub on them I am going to go with enclosure 2.0 or something very similar so the 6mm bolts are not an...

TODO

I made these panels for my 3d printer to make the side panels easier (and cheaper) to fit as they will just be square panels instead of needing machining.The top one with the extra hole in it is for mounting a btt filament sensor.

<p>Just longer shaft by 6mm and longer holder</p> Category: 3D Printer Accessories

Just longer shaft by 6mm and longer holder

Simple Ratrig Calibration Cube

NEW : RatRig Cube v3 is availible... ... Ratrig Calibration Cube v2

This is a shround used on EVA3 with BTT Knomi v2.

Remix of Ratrig "top_endstop_mgn12c" to fit Mgn12h carriage.

A simple mod to the standard files. Stock arms would hit the z rod couplers while there was roughly 11mm of lead screw still available to use. ...this mod ads clearance for the coupler and results in a further 10mm of z travel

This is for those running the V-Core 3.1 beta 1 or 2 toolhead and the funssor CNC super lightweight XY joiners (see photo for the exact model - this is the lightest weight one they make).  Running the stock end stops will result in your toolhead no...

This is an actual ratrig configuration 2020 extrusion front part working.

Designed a quick cover plate for the fan duct hole in the back electronics plate of Mikkel Schmidt's RatRig V-Core 3 design. I may use the duct port at some point but for now I wanted the hole covered. ... It is 2.4mm thick to give room for some top...

Fits in the back of an Ratrig Vcore 3 printer without sticking out. Assembly with 3x10mm caphead bolts. 2x 40mm fans for cooling. mounts for 2.5mm zipties for cable management Din rail mount: https://www.thingiverse.com/thing:4697604 ...

Spool Holder for RatRig Parts for 1kg and 2.3kg spools Needs 150 or 195mm M4 threaded shaft and nuts PLA+ Normal quality

This is so you can mount to the front or the back without interfering with the extruder assembly.&nbsp;&nbsp;You need:&nbsp;2 40mm M5 bolts2 M5 nuts to embed into the “Spool Arm” just pause print and insert at the right layer.&nbsp;1 M5 30mm bolt for...

As I eagerly await the delivery of my RatRig CoreXY printer frame, I've designed this mount for the Chimera to take advantage of dual filament capabilities. Please note that this is version 1, still untested since my RatRig hasn't arrived yet. I...

Needed a handle for my RatRig enclosure doors but since i was self sourcing i needed to make my own handles. Settled on a simple model that is easy to print with no overhangs. 90mm gap between screw holes.</p><p>To install, use M6x12 screws (shorter...

Since I like the design of the original spoolholder 2.0 from Ratrig for its simplicity , I've redrawn it in the same style. ...The smaller one will fit a spools max 80mm wide (almost all 1kg spools), and the larger one will fit maximum 110mm (up to...

Make Flyingbear Reborn compatible with RatRig/VZBot and Eva 3D project For rail adapters, you need M3x16 mm bolts with T nuts For the pulley, you need m4 d5 20mm+ bolts. ...For one corner m4 d5 30mm will be enough (see photo) M3x8 bolts for carriage ...

I re-designed the fan mount from the RatRig assembly and created a new holder for the duct and blower mounting. All parts were printed with PLA for initial testing purposes, except the duct which requires a more heat-resistant material such as ABS or...

Make Flyingbear Reborn compatible with RatRig/VZBot and Eva 3D projectX: 348Y: 322Z: 340BOMM3x16 and M3 T nut: 8+ (better 14+) For rail adaptersX - MGN12H 400mm...450mmY - MGN12C 350mm...365mm (or any compatible with eva 3d project), for 400mm portal...

<p>The hinge is held together by some M3 bolt at least 22mm long.</p><p>You need a Pi camera ribbon cable of about 500mm.</p><p>Remixed from:</p><p><a...