rat rig v core 3d models

A cunning engineer for the rat army wields a flintlock pistol! He bears a striking resemblance to a certain captain who rules over mystical mice with an iron paw. Be sure to explore my other creations at Thingiverse!

By December 29, 1942, a few preliminary drawings had been completed, by which time the concept had been named "Ratte" (Rat) by Hitler himself. These submitted designs went under the titles OKH Auftrag Nr. 30404 and E-30404/1. Albert Speer saw no...

As of December 29, 1942, a few preliminary drawings had been completed, by which time the concept had been named "Ratte" (Rat) by Hitler himself. These submitted designs went under the titles OKH Auftrag Nr. 30404 and E-30404/1. Albert Speer saw no...

Rat Rogue! He's ready to plunder the nearest dungeon of loot, sack at the ready to haul it back in! Perfect for homebrew races like Ratfolk, Ratkin, etcetera. Scaled to be roughly in line with 28mm, will comfortably fit on a standard medium size...

Rat Rogue! He's ready to plunder the nearest dungeon of loot, sack at the ready to haul it back in! Perfect for homebrew races like Ratfolk, Ratkin, etcetera. Scaled to be roughly in line with 28mm, will comfortably fit on a standard medium size...

v

v

Compatibility: - Unity Humanoid compatible - Mixamo and other humanoid animation libraries (MoCap) - Removable Tail for Easy Animation The Model Includes Full Facial and Body Rigging. The Model is Lowpoly with Four Texture Resolutions: 4096x4096,...

https://www.youtube.com/watch?v=yeOU2jdAS0g&t=5s&ab_channel=DavidWilson ___________________________________________________________________ I wanted to use an OmniaDrop on my Rat Rig V-core build, and could not find a mount for it. After a lot of...

Here are the remixed parts to use Gates toothed and smooth idlers. For my setup, the belt spacing got a bit bigger due to the Gates parts being slightly higher. You'll also need a collection of small and large washers - I printed them in ABS and...

<p>Designed this to not have the Screw holes cutting into the chamfer on the side of the part.</p> Category: 3D Printer Parts

<p>Remix of the original cable mount, since pulling a thick shielded cable for the ACC sensor put too much strain on the original mount. Mounts from 2 planes to the 3030 extrusion. ...Not the cleanest remix, but it works</p>

The filament bowden guide (PTFE 4mm) through the housing wall (instead of ordinary hole).

*HX EXTRUDER for EVA Carriage and Ratrig Vcore 3* This is a remix of MirageC's HextrudORT lightweight extruder for the EVA system X Carriage, which is used on various Ratrig printer designs. I had a hard time printing the original HextrudORT...

This is the Fan Shroud mount for the LIS3DH accelerometer (used with Duet 2/RRF). ...I took the Fan Shroud design created by Michael Laws (TeachingTech) and changed the hole size/spacing to match the accelerometer.Print Settings:Material: PETGLayer...

This is a comprehensive overhaul of my original enclosure. I undertook this rework because I relocated the enclosure to the center of the frame instead of utilizing one of the sides. The revised enclosure accommodates: * A 350W, 24v power supply...

Refactor of the RatRig electronics_wire_guide_rear to support a CPAP hose.

I modified my setup to bypass mounting the X-axis endstop on the X-carriage. ...To make it work, I ensured that the Y axis is always homed before attempting to home the X axis.\r\n\r\nTo compensate for the mismatch, I added a 2 mm spacer, using a small...

This is a latch designed for holding 3mm thick acrylic panels to 3030 extrusions. This is basically the design found on the Voron 1.8 electronics covers, but slightly modified to better fit 3030 extrusions. Use double sided tape to hold the clips...

Designed this to not have the Screw holes cutting into the chamfer on the side of the part. ... Category: 3D Printer Parts

BOM coming… The FAN RETURN can be used with or without the following HEPA filter cartridge.  https://a.co/d/hSXwPuz The HEPA filters main purpose is for noise attenuation.  Use the “FILTER_BLANK” if not using the filter or use...

I ended up using a normal microswitch for my X Endstop (only two wires needed in the umbilical) and the stock endstop block was a bit too low. ... This is a slightly (3mm) taller version and whilst at it, I increased the width & thickness of the slot...

You will need8x M3 Brass heatstake inserts - short M3x5x46x M3x8 Countersink screws (for the magnets)2x M3x10 Cap head screws (for the bed cable relief)This mod will give you bed arms a nice and clean look and you don't have to worry about dropped...

Exactly the same model but i have added heated inserts instead of hex nuts

I created a new set of parts for the XY Idler mounts on the front that provides the following benefits - Enables the Belts to be tensioned from the front - Maintains the current look and feel of the Printer - Reduces Parts required and...

Replaces the original y-endstop, which robs you of a couple of mm in y-travel even when set all the way back. Instead, this mounts directly to the top extrusion of the inner frame (see picture), allowing you to move it way back. ... Note that, if...

Material list: - 5 m LAPP Siemens-Standard 6FX 8008 Servoleitung 8 x 0.38mm² + 4 x 0.50mm² Grün 277111-1 ...

<p>it is suitable for the case of using lightweight x tube in the lightweight modification of ratrig-vcore3. ...use M5 locknut instead of T-nut.</p>