rat from tmnt 3d models

So thank you very much Gnomeworks for your work :) Gnomeworks use a paper sleeve to protect balls from falling. I decided to create hard sleeves with a rail system. They perfectly fit together and you can slide the sleeve on the rear to store them...

I've attached a remake of a nice design for the front grip from https://www.thingiverse.com/thing:2897402. I made some adjustments to this design by cutting 1mm off the upper picatinny face because it was too tight with an aluminum rail. I also...

Some detailing was done one the teeth to make them stand out individually a bit more, and some cavities like the nose and eye sockets where colored somewhat darker to give them a bit more depth. I painted the part of the plug that’s visible from the...

40x55mm.you need 2 pieces of rubber band, wire or tape.you need 1 piece of Periscope tube 01 or standard 32mm PVC tube.(Periscope tube 01 89mm long results in a Periscope in/out of 150mm)But you can also use standard 32mm PVC pipe to get a larger...

plug-in your fan with reverse polarity could possibly damage it, thankfully my fan was resilient when I noticed it and still works.Remove everything except the metal backplate (there secondary metal plate that isn't attached to the back and should be...

Make sure all surfaces are clean to ensure good electrical contact.ScrewAdjust the screw used for the probe tip so that it slides smoothly in the guide section.Remove the drive slot or cross from the screw, the Pogo pin presses down on this area and...

if corners of parts lift or the entire parts detach from the build plate. Post-Printing Some parts are printed with a thin embedded support structure that needs to be removed after printing. ...This <a href="https://youtu.be/IWulSZqhvvo">video</a>...

This chamber has been designed to seal well with #1.5 thickness (0.17 mm) coverslips, but any thickness slip from #1 through #3 should work. FILES: -LCIC_35mm_base.stl - chamber sized to match a 35 mm diameter culture dish -LCIC_42mm_base.stl...

I remixed this from the CR10s LED-strip mount found here, which mounts on the X gantry. https://www.thingiverse.com/thing:2738331 I liked the connector that he designed, but I wanted my light to be mounted at the top and not angled, so I modified...

&nbsp;I think this version offers these improvements over the previous version:Improved ease of printing - the hub can extend from the fan on both the top and bottomImproved ease of fitting - the hub pieces can be printed separately (and faster and...

(Mini maps!) Let everyone grab tiles and build your world cooperatively! -Have adventure hooks prepared for different unique location tiles, let players replace Mystery tiles on your map from a random draw bag maybe, who knows? If you want to make...

The world is running out of equipment, we need to think about alternatives. This post accompanies a submission (18 March 2020) to the journal Anaesthesia entitled "3D Printed Circuit Splitter and Flow Restriction Devices for Multiple Patient Lung...

... is in panel shape (mode = Compile) with a pixel size of approximately 0.699 inches. The thickness of the 3D printed object will be 0.5 inches. This customized picture-based 3D model can be downloaded from Thingiverse and printed using a 3D printer.

Use this to mark your current dosage.Create your ownYou can download the files from the git repository and open the SyringeHelper.scad file in OpenScad (you need the includes folder too). <a href="https://openscad.org/">OpenScad</a> is free software...

If you have any lifting/warping on the corners you can add cylinders that is 0.1mm high to act as custom brims. Refrain from using the "Brim" option as it places additional waste on points where it does not provide additional adhesion...

--- Mk II: A Rigid spool holder for Dremel 3D40 / 3D45 This replaces my previous spool holder for Dremel: https://www.thingiverse.com/thing:3088371 The Mk II version lets filament feed from a comfortable angle and with minimum friction. (Previous...

High resolution textures 4k and 2k (you can downscale the textures from 4K to 2K or 1K depending on your needs) exported out of Substance Painter for PBR MetallRoughness, Unreal Engine, and Unity. Geometry is fully triangulated to ensure best...

If the top of the lead screw is constrained by a bearing and belt setup (Ender 3 s1), you will benefit from my anti wobble or tekti's on driven sides. This is a remix that solves the wobbly table syndrome caused by 4 unlevel bearings on a plane,...

Their purpose is to prevent the tray from sliding when placed on top of the lid, both when in play and when storing multiple stacked trays in between sessions. * Optionally, one each of the small and large card dividers. They are intended to separate...

This version has slightly smaller cuts so it'll be tighter when placed on Part 2.4 - Button: Just a button.5 - Compression Spring: 3D Printed spring6 - Top Lid: Thin, flexible top lid to cover the mechanism and prevent it from coming apart.Mechanism...

*** Remove the two comment slashes from the "Includes" at the top of the sketch. Markdown was making it act funny. If this benefits you, and you would like to show me thanks ... [Buy me a coffee!](https://www.buymeacoffee.com/Renaissance3D) ...

I don't have plans to get the expansion anytime soon, but figured I may as well try to accommodate it if I can for the future.I started by removing 2 of the card wells from the Welcome To... organizer, figuring that'd leave 4 card wells for the 4...

Looking at the jack from the backside (solder lugs facing you) and the white plastic spacer inside the connector facing towards the floor, the positive (5V DC) pin is to the far left and the ground pin is to the far right. Please double check against...

And if you like, share it with others!Model DetailsThe model is designed to match the dimensions and airflow mechanism from the original pods, so it will seal the pod when pushed down and open the airflow when in the upper position on the bottle. For...

(rough up the areas to be glued to help with adhesion)&nbsp;Glue the spreader to each mount.Glue &nbsp;corners to one side and latches to the other side.&nbsp;On the latch, I use a little glue only from the hole back. To allow the latch to get more...

Remixed from: https://www.thingiverse.com/thing:4248444 https://www.thingiverse.com/thing:4614658 https://www.thingiverse.com/thing:2506910 https://www.thingiverse.com/thing:3853037 https://www.thingiverse.com/thing:3853049...

... All at OnceSurface Mode: NormalExperimental Extra Skin Wall Count: 0Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.

I would not trust it myself for a long period of time with PLA! So I decided to try and remix this as I needed a ton of support to keep the center cone from falling apart - maybe just my printer, dunno. So here it is. It is a work in progress but...

It features a slot, so it can be removed from closed loops when -for example- thimbles have been installed.The tool is specific to this size of Paracordlock; only needs to be printed once and is reusable.DevelopmentPlease comment if something can be...

The last tweaks took place during the summer and the project is currently in its final stage.Here is the tutorial, it will allow you to build this mod all by yourself from the off-the-shelf tube and a handful of parts.&nbsp;On the budget side, you’ll...