raspberry pi rack mount 1u 3d models

... a RasPi to any flat surface! ...Can use adhesive like command strips, or a combination of the 5 screw holes. Simply ziptie the pi to this mount and you're good to go! ...The large gap under the Pi allows some airflow, or for routing cables underneath.

- aligning the usb ports on the UPS and the raspberry PI was a hassle, but it worked out ok. ##suggestions for improvements - make the lugs larger, and use a brass insert that is melted into the plastic. - print with fewer vents - they make it...

The wall mount from max3d was too short to be mounted with Pi power port facing upwards so I remixed his wall mount and extended it to 80mm so that 7" screen could be mounted to a desktop surface. 

This is a custom take on the [Raspberry Pi Stackable Tray](https://www.thingiverse.com/thing:2187350), built from scratch, with a focus on improved reliability. The default design is prone to breaking under stress, which is why I opted for screw...

I designed this for my new lack enclosure. ...It holds a standard 1/4 switch for lights and a Pi on/off switch that is secured by two tie mounts on the back side.

This is a mount for Raspberry PiIt is compact so you can mount them side by side.It is raised so the mounting screws won't interfere with the board.The screw holes are secure, so they won't break off.

Simple Wall-Mounted Pi Case for Easy Installation and Removal. The case slides onto the wall mount, allowing for hassle-free installation and removal by simply screwing it into place on the wall. The triangles on the Easy Print STL version are...

Hi! ... This is a quickly designed mount specifically for this case: https://www.thingiverse.com/thing:3726254 Raspberry is not fixed in the mount, it can be quickly removed and put back on. ... The model is not perfect, but it works :)

Most other mounts force you to install the Pi directly into theirs, making it a hassle to access if needed - you'd have to detach the entire thing from the monitor's back. This design allows for full access to ports on all sides (except for the SD...

Simple yet stable camera housing/mount for the Pi camera 1.3 You will need 1x M5x50 bolt and an M5 nut or 2x M5x20 bolt and 2x M5 nut to assemble the mount Category: Electronics

Created this to mount my Pi with screen to my Hypercube. ...There are mounting holes for the my buck converter on the back to connect directly to my PSU.There's 2 versions: one with it 90 degrees vertical and one angled 35 degrees.

I remixed the original build due to my mounting screws being too long and hitting the PI, so I adjusted them to match the dimensions of my display panel. ...To achieve this, I tilted the mount backwards by 30 degrees and secured it on top of the printer...

Created this to mount my Pi with screen to my Hypercube. ...There are mounting holes for the my buck converter on the back to connect directly to my PSU.There's 2 versions: one with it 90 degrees vertical and one angled 35 degrees.

I started to unlock the full potential of my old Raspberry Pi by diving into AstroPrint and discovering a whole new world of possibilities.\nThe frame is incredibly sturdy and effortlessly simple to work with, making it perfect for printing...

I wanted an adjustable Pi Camera Mount that I could tied with T-Nut from front corner of my Ender 3 too many other printer changes happening to use most other mounts I had found, and I haven't nailed down Pi Case or location yet so this fit the bill...

... panel but didnt see one so designed this. Its designed around the original Pi Pico. You'll need 3mm countersunk screws to mount it to your chosen surface and M2 2mm bolts to screw it to the mount, maximum M2 of 8mm. ... Category: Electronics

Hi, this is my take on a Rasbery PI server rack mounting case. Its designed to print without supports and fit most versions of PI. This one was deigned with the PI 3 and Le Potato in mind. The lid is a press fit and can currently on fir on the RH...

Though, I must confess, the 2nd iteration needs a tweak - the distance between the mounting surfaces requires an adjustment of approximately .015 inches to achieve an ideal fit. Please be aware: the current design holds firm but leaves room for...

You can simply attach this camera mount to a pi using glue or elastic bands. The mount is specifically designed for the official cameras, such as those from RS Online (color: 7757731 and infrared: 7902811). Just follow these easy steps: Print out...

I designed a custom wall mount for the GeeekPi Case since I wanted to adore the design of this case. The Case:(https://www.amazon.de/gp/product/B07TVLTMX3/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1) You can screw the bottom part to...

... This is a case and bracket with a ball mount for a [focusable Pi camera](https://smile.amazon.com/gp/product/B07DNSSDGG/ref=ppx_yo_dt_b_asin_title_o00__o00_s00?linkCode=w61&imprToken=TGqrppU29aXlLx6Sq9P-vw&slotNum=15&ie=UTF8&tag=tv-auto-20&th=1).

Based on the idea of a failed project on Thingiverse that didn't quite work out for me, specifically the adafruit pi camera v2.1 model. I decided to start from scratch and create my own design, this time relying solely on friction to hold the mount...

I needed a panel mount to mount a raspberry pi inside my Geeetech printer to run octopi. ...I found this 1u rack mount and liked it but wanted it a little thicker and rounded edges to fit my application.

This is a case and bracket with ball mount for a focusable Pi camera. There are two different types of frame mounts a tabbed version and ball version. There are two different sizes of frame mounts for 2020 and 3030 extrusions. To assemble you'll need...

It has small cutouts at the top for vents (not concerned with heat on my PI so I didn't put much thought into it), cutouts for the IO on all sides, and a cutout for a ribbon cable to exit through. Slide it in through the top (It is pretty much an...

A fan mount

one shot print camera mount.

one shot print camera mount.

I updated the design by 3dkarma for the Pi 3b+ and added a simple clip to bolt it onto the support of my MP Select V2 Category: 3D Printers

This revised version is specifically designed for the Pi 4, but works seamlessly on my Pi 3B as well. 2020/03/21 Update: A label piece has been added. ...I prefer writing directly on it with a sharpie, but consider applying tape first to create a...