raspberry pi rack mount 1u 3d models

The face plate named decora_rpi_3b.stl should work for the Raspberry Pi 2, but it didn't fit the Raspberry Pi B+ I checked. I wanted the tolerance to be pretty low, but I only have one Raspberry Pi 4b to verify with. Please let me know if you have...

Made the front panel mounting holes smaller so you can use the screws that come with the 1U decora panel https://www.ebay.com/itm/264097865148. ... To assemble, self-tap the screws through the panel into the bracket and faceplate/blank.

All models are the same as the original this thing was remixed from except that they offer a mounting option at 83.3mm as well as 96.8mm.

My two setups were: - 15-bay with single Raspberry Pi 4 8GB - 12-bay with dual Raspberry Pi 4 2GB For the 15-bay print: - (5) SATA 3-bay - (2) Double Back Tray Cover - (2) Double Back Tray - (2) Side Arm - (1) Single Back Tray Cover - (1) Single...

Raspberry Pi 4 Case for 1U server rack, with space for hats. Top uses M2.5x5 screws Bottom holes are made for M2.5x8 screws from below into posts above Raspberry Pi. Note: Remove SD card prior to installing RaspberryPi to prevent possible SD card...

This is a variation of a 2U bracket that I worked on earlier: * [Raspberry Pi 4 2U rack-mount bracket](https://www.thingiverse.com/thing:4078710) and uses the same tray design, so you can move units between these two mounts easily. This design fits...

Rack mount for the Raspberry Pi 4, with additional room to fit hats (such as the POE hat). Top uses M2.5x5 screws Bottom holes are made for M2.5x8 screws from below into posts above Raspberry Pi. ... Note: Remove SD card prior to installing RaspberryPi...

The printed elements are designed to perfectly fit the openings in the frame and provide a clever 4 slot Raspberry Pi 19" rack mount. The locks use a simple push/pull lock mechanism (snap-in rivet). If you want to save some money, you can just...

Remix to fit orange pi 0

I found ButlertheButler's mount for the pi https://www.thingiverse.com/thing:4167265 and he had a link to the Procraft Decora rack mount. I picked one up and his prints were perfect for it. I like to run my pi boards from a SATA SSD, so I designed...

This is a 1U rack mount NAS case designed for a Raspberry Pi Compute Module 4 IO board. It will accommodate up to 4x 2.5" HDD's or SSD's. The lid is in 2 parts, this was mainly done so they could be printed on a smaller printer whilst the CR10 Max...

Vertical mounting bracket for https://www.thingiverse.com/thing:4125055 No need for supports, although you can add them for the mounting holes.

I liked the design of the [Raspberry Pi 4 1U rack-mount bracket](https://www.thingiverse.com/thing:4125055), and it fit my needs, but the PoE was going to be a bit expensive. I created a mount to hold a 5v 75W power supply that can power up to 4...

This works well with my rack mount remix with the sides removed allowing extra space to the left and right of the Pi. Print SettingsSupports: Doesn't MatterResolution: 0.2Infill: 25Note: If bridging is not an issue, it can be printed upright or...

To save my rack size, I have created an enclosure, that fits two Raspberry PI computers next to 10” switch, replacing standard brackets/adapters. This one fits my TP-Link TL-SG1024D switch replacing original brackets and fitting it’s screws. Please...

... cut into 3rds that allows me to solder jumpers without interfering with the hat itself. This works well with my rack mount remix with the sides removed allowing extra space to the left and right of the Pi.

Added toolless fastening for Raspberry Pi Trays Reduced height of front handle to allow for easy removal of ethernet cable. Only verified compatibility with Raspberry Pi 4B. Compatible with POE HAT Longevity of part not tested. (will be...

Raspberry case for the sensor

Combined the cover plate and Pi 4 mount using a unique adhesive solution. ...The parts can be found here: https://www.thingiverse.com/thing:3022136 I secured them together with JB Weld's PlasticWeld, but if I were to reprint these components, I would...

Same instruction as the original designers : Print Face Down Use 2 - M2.5 Screws to attach the Pi Use 2 - #8-32 machine screw with hex nut to attach the Monoprice Blank Fiber Patch Panel - 19 Inch | 3Lgx Cassettes 1U : https://amzn.to/3KM2X4m M2.5...

This is just a modification of fals3illusion's pi4 mount to make the holes larger (.25 inches). ...The same size as his pi 3 mount.

A bracket to mount the Raspberry Pi 4 in a standard 10-inch server rack. This will fit 3 RPi 4 units using Power Over Ethernet (PoE) in a 1U. This is a remix of this original 19-inch rack-mount-bracket by russross:...

This is a tray for the 1U Raspberry Pi 4 rack chassis that holds *two* M.2 SSD USB enclosures like the SABRENT M.2 SATA SSD to USB 3.0 Aluminum Enclosure (EC-M2MC). ... Enclosure can be found for $17 here:...

Mixing this incredible https://www.thingiverse.com/thing:4125055 from russross and https://www.thingiverse.com/thing:3558220 from therealodie to make a raspberry rack with hdd (2.5") support. 8 hdd holes to allow fitting disk with connector in...

... I need to some Keystones that connect to my gear. ... These Fit into 1U LGX Blank Fiber Patch Panel - 19 Inch The keystone I used was from https://www.thingiverse.com/thing:2668816 Added Raspberry Pi 2/3 mount with keystones.

Customized version of https://www.thingiverse.com/thing:4125055 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4125055

Customized version of https://www.thingiverse.com/thing:4125055 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4125055

Customized version of https://www.thingiverse.com/thing:4125055 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4125055

Customized version of https://www.thingiverse.com/thing:4125055 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4125055