raspberry pi for ender 3 3d models

It's made to work for the Ender 3 v2, but assuming the other Ender 3 versions use the same rails it should work for them too. Designed to use the left side rail, but can be mirrored in the slicer or modeling software very easily to be used on the...

### **This now lives on [Printables](https://www.printables.com/model/347670-ender-3-zaxis-camera-mount-for-raspberry-pi-camera) and may not be up to date on Thingiverse** Codemonkey1973's [Ender 3 Camera Mount for Raspberry Pi Camera...

Ender 3 V2 drawer replacement for Raspberry Pi with Meanwell Power Supply Space for MEANWELL original RS-15-5 5V 3A Single Output Switching Power Supply AC-DC (I first used a DC/DC converter but it brunbed up so I decides to use an extra Power Supply...

This design is a remix of my Raspberry Pi 3 Model A+ case for the Raspberry Pi Model B+: It adds a case to your Ender 3 (Pro) that fits a Raspberry Pi 3 Model B+, a 10A relay (for switching LEDs on/off), a 30A relay (for switching printer on/off), a...

This design adds a case to your Ender 3 (Pro) that fits a Raspberry Pi 3 Model A+, a 10A relay (for switching LEDs on/off), a 30A relay (for switching printer on/off), a buck converter (for powering the Raspberry Pi from the Ender 3's PSU) and a...

This is a remix of Tronnics Ender 3 Touchscreen Case & Holder for Raspberry Pi, made compatible with the Raspberry Pi 4 and its 4" HDMI LCD screen. The original was designed for the Raspberry Pi 3 (with a 3.5" screen) and other possible models. To...

______ Remix aus dem Raspberry Pi 3B+ case (3, 2 & B+ also fit) von dktosoch und einem Cabel Clip den ich leider nicht mehr im Original auf Thingiverse finde (solltet ihr das Original kennen, schreibt mich bitte an und ich nehme diese mit auf). Das...

This is a revised remix of the original remix by Codemonkey1973, specifically designed to eliminate any remaining lettering from the flat surface.

Therefore, I created an additional stand for the Raspberry Pi Case that provides extra height for the camera while utilizing a short cable. **Update 1** After being dissatisfied with the previous model, I revisited my digital drawing board to make...

This custom PSU case for the Ender 3 replaces the stock case and adds a spot to mount a 3v relay, and a separate attached enclosure to mount a Raspberry Pi 3. The enclosure has a lid that slides on and off easily to access the PI. In addition, there...

This is a 109mm custom male / 3 pins arm adapter for the [custom mount for the Ender 5](/thing:3809015), designed by [Dwiekawki](/dwiekawki). ...It allows you to extend the arm by alternating female / 2 pins and male / 3 pins arms.

I personally used one from rs components as they have quiet 24v ones https://americas.rsdelivers.com/product/rs-pro/od4010-24lb/rs-pro-24-v-dc-dc-axial-fan-40-x-40-x-10mm-85m-h/1442036 This is a remix of two Ender 3 electronics cases:...

I personally used one from rs components as they have quiet 24v ones https://americas.rsdelivers.com/product/rs-pro/od4010-24lb/rs-pro-24-v-dc-dc-axial-fan-40-x-40-x-10mm-85m-h/1442036 This is a remix of two Ender 3 electronics cases:...

Raspberry Pi Bed Mounted Camera Arm - larger hole (16mm) for beds using solid silicone spacers instead of springs.

For S1 Pro only. ...The rest parts for this mount you can find here > https://www.printables.com/model/3407-articulating-raspberry-pi-camera-mount-for-prusa-m

Raspberry Pi Bed Mounted Camera Arm - larger hole (16mm) for beds using solid silicone spacers instead of springs. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill: 10% Triangle,...

When installing be careful to not clip over your wires.Printed with PETG with 100% Infill using PrusaSlicer.Remix of:https://www.thingiverse.com/thing:5365986/files...

This only applies to you if you're like me and not willing to move the Ender 3's screen to the other side. So I designed an angle arm that attaches nicely to the initial mount and camera case. The two pieces are held together with a single M3 screw...

Remix for this model:Ender 3 s1 pro mountYou can use this piece to add an articulating system to your ender 3 s1 pro, I personally use it for mounting an articulating arm with a camera on top.A filet for the holes so it's easier to print, video also...

<p>Fits on top cross bar with 3mm screws and t-nuts.</p> <p>I fount that the bowden tube and wiring could get snagged on the mount. ...So V2 has rounded edges and dose not sit flush with bottom of the 20x20 extrusion.</p> <h3>Print Settings</h3>...

The new design fits securely onto the top cross bar using three millimeter screws and T-nuts. Upon closer inspection, I discovered that the bowden tube and wiring were prone to getting snagged on the original mount. ...To address this issue, I've...

Fits on top cross bar with 3mm screws and t-nuts. I fount that the bowden tube and wiring could get snagged on the mount. So V2 has rounded edges and dose not sit flush with bottom of the 20x20 extrusion. ...Print Settings Rafts: Doesn't Matter...

This is a remix of the following projects: https://www.thingiverse.com/thing:3030160 https://www.thingiverse.com/thing:3399116

The original display's design has been revamped to perfectly complement the Pimoroni Hyperpixel display.

Thanks for supporting my designs! Print Settings Printer Brand: Creality Printer: Ender 5 Rafts: Doesn't Matter Supports: Yes Resolution: 0.2mm Infill: 50% Filament: Any Any Any Notes: I used Carbon Fiber PLA for rigidity but it's not required. ...

The following video has full assembly instructions: https://youtu.be/aPOUPXh9m-g Hardware Needed: Camera: Arducam 5 Megapixels 1080p OV5647 Camera Module https://amzn.to/2IYQOdl Camera Mount: 4 x M3 12mm Screws 2 x M3 8mm Screws 6 x M3 Nuts...

Watch this video for a step-by-step assembly guide: https://youtu.be/aPOUPXh9m-g Required Hardware: Camera: Arducam 5 Megapixels 1080p OV5647 Camera Module - available at https://amzn.to/2IYQOdl. Mounting System: 4 M3 screws, each 12mm long. 2 M3...

My BLTouch (left of Petsfang) was bouncing into this so I cut out the section getting in the way. ...Did a quick modification in TinkerCAD if anyone wanted to get around this without cutting.

Minimal Raspberry Pi Holder for Ender 3 Pro Created a basic and quick-to-print Raspberry Pi holder specifically designed for the Ender 3 Pro. This design should work with other types of Pi boards, including the Pi 3 B+. It may also be compatible with...

A Raspberry Pi enclosure for Ender 3 v2 that has room for mounting 2 x buck converters and 2 x relays for PSU control/LED lighting control. Intended to be mounted out of the way on the right rear rail with 3mm t-nuts. Buck converters are the...