raspberry pi ender 3 pro 3d models

... Gehäuse kann innen ein 20mm Lüfter verbaut werden. Der Raspberry Pi wird mit M2,5 * 8mm (selbstschneidend) Schrauben befestigt. Wenn euch der Remix gefällt lasst ein Like da. ...Für Verbesserungs- oder Änderungsvorschläge bin ich immer offen.

Because my Raspberry Pi 3+ had trouble powering two IR LEDs, I opted for just one this time around, and it still illuminates the printbed more than sufficiently! Here's the camera I used:...

I built this dock specifically for my raspberry pi, which is already encased in a protective housing and running octoprint. The dock can be easily positioned on either side of the printer and neatly slots into place within the 40x40 aluminum...

A Raspberry Pi 3 A+ case that allows a pi to mount to the extrusion rails under the print bed. I wanted a mounting option that did not increase the printer's footprint and did not require hardware. I also took the liberty of providing 3 other...

This is a remix of Harryb1991's RPI4 case with added rails for Ender 3 and CR-10

Raspberry Pi Camera Mount - flexibility, no screws, no other hardware required. This is another raspberry pi camera mount. I made this by making modifications to the files below. They were great but didn't allow the flexibility I was looking for. I...

The fan mount is for a 30x30mm fan like the ones that typically come with Raspberry Pi cases is also slightly adjustable to center airflow over the processor or clearance (should it be required) for buck converters. ...(this is why there is a space...

None of the existing Raspberry Pi stations I found included accommodations for fans, proper airflow, camera cables, the USB port, either HDMI port or the audio jack. This design aims to address all of those issues. The base clips to the existing...

To take it to the next level, I drilled a hole into the case to give easy access to the gpio pins on the raspberry pi. This modification should be adaptable to most Creality machines, but confirmation is needed. ...The cap remains unchanged from the...

For Raspberry Pi 4B. I couldn't fine one with rails, so I remixed this in Tinkercad with https://www.thingiverse.com/thing:4176051 I had to make the top taller to avoid needing supports, so there is a little gap between the front i/o and the case. ...

I am planning to make another LCD screen into the top cover, for OctoPrint. I have included the f3d design files so you can make changes and tweaks. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: 0.2...

I wanted to use this case design for my ender 3 but wanted it to stay in place but also be easily removeable if needed so I created this thin but solid mount holder that attaches to the printer at just the right distance from the USB port for a short...

Meshed together two different Camera Mounts that were already on Thingiverse to create a Ender 3 S1 mount that works with my Octoprint camera. ... Update: Added version 1.1 that makes the camera mount slide on the the printer arm much tighter and fits...

mount it anywhere.... ...If you already have your pi in a case use mounting holes at back...

Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.02mm Infill: 25% Filament: Hatchbox PLA Notes: Infill doesn't matter very much. Design is mostly solid. Print in given orientation. ... ...

... the right side. For right side optional drawer see: https://www.thingiverse.com/thing:5138213 or https://www.thingiverse.com/thing:5138213 It's my first remix ever, so any suggestions are welcome. Printed and fitted on my Ender 3 V2 Neo.

Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.02mm Infill: 25% Filament: Hatchbox PLA Notes: Infill doesn't matter very much. Design is mostly solid. Print in given orientation. ... ...

Also added cutout for USB passthrough on front of the draw Pi runs at about 45c while printing (No heatsinks installed) Hole spacing for LM2596 used are 58mm x 32.5 Hardware required 8 piece M3x6mm (Pi and Converter can use 2 each if you haven't got...

Remixed from https://www.thingiverse.com/thing:4192636 to place the Pi on its side so as to take up less space. Also removed some of the port holes next to the power cable. ... Re-mixed in TinkerCad.

Malolo's Rpi case is perfect! ... I just added lateral arms to mount it on the left side of a LK4 Pro, and a larger slot for the camera flex cable.

Malolo's Rpi case is perfect! ... I just added lateral arms to mount it on the left side of a LK4 Pro, and a larger slot for the camera flex cable.

RbPi holder for Ender 3Pro/v2 Remixed dual-sided SD slots, and enable screw holes to print without support. ... Compatible with 9cm * 6cm cases like this one in the link below: ...

I didn't put a fan in the design because I have modded the original 40mm controller fan with a 80mm fan, it pushes a lot of air through the vents, should also be able to cool down the Pi. Fan Mods I used: ...

... -2 piece of M3 x 20-25mm screw and one M3 x 8mm screw + 3 M3 nut If you don't mind, please download it from my printables profile and leave a like if oyu liked it. https://www.printables.com/model/533433-ender-3-pro-raspberry-camera-front-holder

Easy raspberry pi hanger for Ender 3/ Ender 5/Pro rails. No nut or screw required, just hangs off the rails. You can pick it up and move it around easily. ...I generated a tree support to print mine.

Raspberry-pi case that mount onto the Ender's v-slots

Started with a Pi Cam mount for the Ender 3, and when I designed it, I saw I had to make a rod just longer then the width of a Raspberry Pi. Then found the great design of Esquilo and integrated that in my design. ... Made for it to just be long...

With this case, you can upgrade your Ender 3 Pro and use the full power of the Raspberry Pi to monitor printing, adjust printing parameters, and even get remote access to your printer. Access to the back of the printer is conveniently done through...

ATTENTION: PRINT ONLY WITH WELL-CALIBRATED PRINTERSNot being able to find a case to contain the electronics and the Raspberry, I decided to create one myself.The parts you will need are M2.5x5 or m2.5x10 screws for the raspberry and m3 hot inserts...

The original Pi Camera mount from the website (octoprint) does not fit the bracket on the Ender 3 Pro. I made the slot wider (2.5 mil instead of 2) and added Two (2) slots to the bending arm. These slots serve a purpose and allow the user to install...