raspberry pi ender 3 pro 3d models

Case for a Raspberry Pi 4 that mounts to an Ender 3. Main sail logo and access holes for gpio and camera. Requires (4) M2.5 X 22 socket head cap screws (McMaster-carr part #91292A312) and (4) M2.5 heat-set thread inserts (McMaster-carr part...

Control Box Enclosure for Ender 3 w/Raspberry Pi 3B for Octoprint Print in position that it will be used, not as shown in image, rotate 90 degrees I printed without supports to reduce printing time. The rear cutout is large stretch and might get...

Ender 3 bed handle with a Raspberry Pi cam mount socket (https://www.thingiverse.com/thing:2886101). Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill: 20% How I Designed This...

I designed this Raspberry Pi Case for my Ender 3, to fit perfectly in and to be used with an 80mm Fan. I connected the fan and the power connection directly to the pin header of the Raspberry Pi even if it's a bit tight under the fan for the Power i...

This is the sleeve case for the raspberry pi, with a camera slot, paired with a LCD screen mount for the ender 3 V2. If you use the tent style creality enclosure, the lcd doesnt fit inside the enclosure, so you need to relocate it outside the...

This print was designed to work on almost every ender 3 model and CR10 model.=======================================================================================================COMBATIBILITY:Tested: Ender 3, Ender 3 V2, Ender 3 V2 Neo, Ender 3 S1,...

... a better mechanism to hold the back/front/left/right pieces together. The mounting base for the Pi is available from this link: https://gallery.autodesk.com/projects/98029/raspberry-pi-2--3-mounting-plate It can be screwed on the "back"-panel

I added a rail mount that allows me to securely attach my Pi to any of the convenient rail ends on my Ender 3 Pro printer. ...To bring this project to life, I used a 0.6 millimeter nozzle size, printing at a moderate speed of 125 millimeters per minute...

This is a Raspberry Pi Zero 2 W case for the Ender 3 Pro. After building a Voron and using Klipper and Mainsail/Fluidd, I had to convert my Ender over. Highly recommended I wanted something that mounted close the MCU so I could use UART between my...

... the ender 3 v2 cause that's all I have. **This is only confirmed to fit the raspberry pi 3b+** Filament: Matterhackers MH-build ABS Infill: 20% Nozzle temp: 260 Bed Temp: 110 Layer Height: .16 Cooling: off Plate adhesion: Brim Wall line count: 3

This is a custom Raspberry Pi camera case and arm for the Ender 3 printer, optimized to work seamlessly with OctoPrint. Some minor adjustments may be needed to ensure a snug fit between the arm and the bed support - a little sanding should do the...

Raspberry Pi A+ Case Modified for Enhanced Performance and Versatility: Key Modifications Include: * Precision holes drilled for seamless integration of a 25x25 heatsink, ensuring optimal heat dissipation and ventilation on the top side. *...

Introducing a revolutionary new GoPro Mount and Housing specifically designed to unleash your Raspberry Pi's visual potential. This ingenious creation is a remix of the finest existing designs, expertly crafted to provide an unparalleled level of...

... Left Side and Right Side. Maybe you can use this mount in combination with my Raspberry Octoprint case for the Ender 3 Pro: https://www.thingiverse.com/thing:4334333 Take a look at my other designs: https://www.thingiverse.com/dasmani01/designs

Remix : - Less material - Upper camera - Ribbon exit from bottom Works for Ender 3 and Pro

Remix : - Less material - Upper camera - Ribbon exit from bottom Works for Ender 3 and Pro

Ender 3 Raspberry Pi Case for GeeekPi Cooling Kit Remixed from Ender 3 Raspberry Pi 2/3 mount (UPDATED V2) by giacomo30196 https://www.thingiverse.com/thing:3016364 This case is designed to fit into the T slot of the 40x40 Aluminium Extrusion and to...

Did a little remix of this simple yet effective Rasbperry Pi Case for the original ender 3.Modifications:thickened the walls for greater strengthadded m3 screw holes for the lm2596 and shifted one of the holes by 1mm so that the screw would face...

Simple mounting solution, without screws, for a Raspberry Pi 4 in an Aluminium Armor case.&nbsp;Designed for the Ender series but should fit any printer with similar construction.Easy print. ...No support required</p>

I made these clips as a way to (somewhat securely) mount my Raspberry Pi to my Ender 3 rails while still allowing it to be easily removed, in seconds, without tools. The case that I'm using is one that came with my Pi touch screen(brand:...

Octopi running on raspberry pi Zero W (1st gen - yes it works, though the install said not good idea; had some sitting in drawer and flashed Octopi). Used Cura with Octopi add on and now sends the sliced files wirelessly. Needed a holder for the pi...

Le Raspberry Pi 3b+ se fixe à l'aide de 4 petites vis (Type ordinateur portable) et le boitier se fixe sur le châssis de la Creality Ender 3 V2 avec 5 vis M4 et écrous en T. ... Quelques liens : - Raspberry Pi 3b+ :...

Took the Raspberry Pi 3 A+ Case from CoreElectronics and modified it to fit the ender3 v2 support bracket base from kingstonrichard. Also modified the case to include the standoff design from kingstonrichard's case. - Case was a really tight fit...

This Raspberry Pi case is designed for the Raspberry Pi 3 and has a Trash can Mac Pro look. Its intention is to be used as a small DIY desktop PC/Mac Pro alternative. Please note that this model is designed to fit two 40x40x10mm 5V PC fans, colored...

Check out all of my other designs under my profile on Thingiverse: https://www.thingiverse.com/The_Craft_Dude/designs This Raspberry Pi case is designed specifically for the Raspberry Pi 3 and is modeled after the iconic Trash Can Mac Pro. The...

Ender 3 V2 Bed mounted Raspberry Pi 2 camera, mounting arm and bracket This is a mashup of these three designs as I wanted the more secure mount from the CR10 version https://www.thingiverse.com/thing:2833820 as I didn't like the pivot mount that...

Inspiration for this project was Raspberry pi case designed by Hesi-Re ( https://www.thingiverse.com/thing:3700643 ) because I have fitted in my Ender 3 drawers designed by DWS_design ( https://www.thingiverse.com/thing:3416444 ) none of the cases...

My design incorporates a clip that positively connects to the front of the Ender 3 (not sure about pro) without tools or hardware. It can also be easily removed in a flash. My favorite part is that I integrated loops for the ribbon cable. The cam...

I'm excited to share my latest Raspberry Pi camera mount design, which features a clip that securely attaches to the front of the Ender 3 (or possibly the Pro) without requiring any tools or hardware. The best part is that you can easily detach it...

This is a case for Raspberry Pi 4 that is mounted to ender 3 v2 frame. Probably will fit any ender 3 and similiar printers. Case will fit the Pi, 40x10 fan with room for little heatsinks. I used 6mm heatsinks. There is not much room left after them...