raspberry pi 4 case with fan 3d print

This Raspberry Pi 4 case was designed with the goal of housing an SSD SATA drive and a 30mm x 30mm x 7.6mm PWM fan. I like running SSDs on my Raspberry Pi(s) that I have critical services running on like my MQTT broker and OpenVPN server because...

If using the fan option, the fan may be slid in from the front and will be held securely behind the small "bump" (see photo). Slide 30MMx30MMx8MM fan in from the front, it will "snap" in behind the small bump Temperature Management...

I couldn't find a Raspberry Pi 3B+ case compatible with the kind of cooling fan that I have. ...So I decided to make one myself!

I wanted to try designing my own case for a project I did for my father and I had some some spare 80mm fans laying around and this is what I came up with. I've already tested the Raspberry Pi 4 model and know that one works, but I have not tested the...

This is a custom case designed specifically for the Raspberry Pi 4 B. It can be printed without any supports and has been thoroughly tested on a Prusa i3 MK3S. The case is tailored to accommodate a 30x30x8mm fan, which can be purchased at...

The official Raspberry Pi 4 case is a nice design, but unfortunately, its creators chose not to include any ventilation at all. To address this issue, I created a template that makes it easy to add a fan cutout for a 30mm fan like this one:...

I needed a hole for the two fans to let me mount this cover on my Raspberry Pi 4, so here it is!

CubicMilliliter's original description below: ======== This is a press-fit Raspberry Pi 4 dual-40mm-externally-installed-fan case, which also exposes the GPIO pins. This design attempts to combine various elements from other Thingiverse...

This is a remix of this case (https://www.prusaprinters.org/prints/24942-raspberry-pi-34-b-case/comments). I added some height to create space for a fan. The case is designed to fit a 40x40x10mm fan like the Noctua NF-A4x10 5V.I have made a...

I'm remixing John_Sinclair's design for a Raspberry Pi 4 case with two major modifications: I had to accommodate an oversized 40mm fan as a cooler and create a slot for passing a ribbon camera cable through. The fan is somewhat loose, but a small...

Remixed Case to hold Pi 4 + Waveshare 2CH CAN + 40mm fan. ...Includes access hole for the screw terminals.

These are parts to upgrade the Raspberry Pi 4 + Ice Tower Cooler Vertical Case to use the new dual fan configuration. Original Ice Tower Vertical Case here: https://www.thingiverse.com/thing:4152073 My other dual fan Pi 4 Ice Tower case here:...

This is a press-fit Raspberry Pi 4 dual-40mm-externally-installed-fan case, which also exposes the GPIO pins. This design attempts to combine various elements from other Thingiverse contributions, which I could not find an existing all-in-one design...

Case for a Raspberry Pi 4FeaturesVESA mount (75mm x 75mm)Internal fan mount (40mm x 40mm x10) - optionalThread inserts (case and pi mounts)Footer pins - optionalRequired partsRaspberry Pi 4Optional partsFan 40x40x10, 5V → Noctua NF-A4x10 5V incl.

Remixed Case to hold Pi 4 + Waveshare 2CH CAN + 40mm fan. Includes access hole for the screw terminals. ...Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 200 Infill: 15 Filament: PolyMaker PETG Red Category:...

I wanted to use the stock Noctua plug to connect to my Raspberry Pi 4. (You have to switch the power and ground pins to do this). But then the (Excellent, btw) case by Malolo would no longer fit over the fat Noctua fan connector. ... I edited the...

This is a compact case/cover for Raspberry pi 4 that prioritizes minimalism while accommodating active cooling through a small fan. The goal was to craft the smallest cover possible, one that allows for the installation of a tiny fan without...

I couldn't find a Raspberry Pi 3B+ case compatible with the kind of cooling fan that I have. ...So I decided to make one myself!</p> Category: Electronics

I wanted to use the stock Noctua plug to connect to my Raspberry Pi 4. (You have to switch the power and ground pins to do this). But then the (Excellent, btw) case by Malolo would no longer fit over the fat Noctua fan connector. ...I edited the design...

Raspberry Pi 4 FAN Holder (30x30mm)

I widened the micro-HDMI port to accommodate the official Raspberry Pi 4 micro-HDMI cable.

... a few times. The bracing behind the camera is designed to be trimmed with a blade carefully. A few small blobs of super glue will keep in place and can be pried off if needed. There is not much space - will not fit a fan. ...MIGHT fit a heat sink.

The Argon40 Pi Fan Hat is a smart fan designed specifically for the Raspberry Pi, available for versions 4, 3B, and 3B+. This innovative device allows users to set their own temperature/fan speed curve, making it ideal for quiet desk use. No longer...

I made a small case the same size as the circuit board of raspberry pi4. You can install a heat sink and a 40x40x10mm or 30x30x7mm fan. I am fixing the case with 2Mx8mm screws. Please enjoy! Print Settings Printer Brand: Creality Printer: Ender 3...

This is a simple housing for the Raspberry Pi 4 which is very easy to print and doesn't need a support structure. The housing doesn't need any screws. ...

If you do not know how to run two fans at once from your Raspberry Pi, take a look at the pinout diagram. Connect the positive wires to the 5V outputs and the black ones to just any ground pin. ... You can use any 5V fan you want, but if you want the...

Based on the best Pi_4 case I've found anywhere by Harryb1991 - brilliant case!!! Because I have an OctoPi camera I needed to fix the Raspberry Pi to the printer so it wouldn't get knocked and pull out the camera cable. I've modified just the...

After looking for a pi 4 case, for my new mini argon one fan, I decided to modify plammers (https://www.thingiverse.com/thing:3714695) to enclose the fan housing and include some holes for ventilation. ...You will need 4 M3x15mm screws which will thread...

After looking for a pi 4 case, for my new mini argon one fan, I decided to modify plammers (https://www.thingiverse.com/thing:3714695) to enclose the fan housing and include some holes for ventilation. You will need 4 M3x15mm screws which will thread...

... in the original post. Many thanks to the original poster: https://www.thingiverse.com/tipam/designs This Pi 4 case is probably the best one I have printed so far (and I went through quite a lot already), especially the stand design is really cool!