raspberry pi 3 prusa mk3 3d models

Raspberry Pi 3 B+ case for Prusa MK3S & MMU2S (OctoPrint / OctoPi setup). Screws needed (cap head hexagon socket drive screws [the same type used for MK3S assembly]): 4 x M3x18 3 x M3x10 (you can use screws longer than 10 mm as well, but not...

What you need: * 8x M3x8 + 8x M3 nut's (cablemounts) * 4x M3x8 + 4x M3 nut's (Raspberry) * 2x M3x8 (frame) * 4x M3x8 + 4x M3 nut's + some kind of (rubber)washer (Einsy) * Countersunk 3x M3x10 + 3 M3 nylock nut's (brace to enclosure) * Countersunk 8x...

This easy-to-print bracket mounts a nice Raspberry Pi case to the Prusa i3 MK3 printer's existing holes without any cutting or drilling, and without making a permanent change to either one. It leaves all Pi ports open. This bracket requires only...

I've removed the end sleeve and use solder to get an L-Shape End. What you need: 8x M3x8 + 8x M3 Nut's (Cablemounts) 4x M3x8 + 4x M3 Nut's (Raspberry) 2x M3x8 (Frame) 4x M3x8 + 4x M3 Nut's + some kind of (rubber)washer (Einsy) Countersunk 3x M3x10 +...

A snap fit case designed around the low profile ice cooler for Raspberry Pi 4B. Uses the screws and other hardware included with the low profile ice cooler. I used two M3x14b screws from my MK3S+ spares bag to attach it to the printer. ...There is...

Based on the awesome Articulating Raspberry Pi Camera Mount( https://www.thingiverse.com/thing:3114849) project, this uses a Loc-Line ball joint coolant hose as the camera arm. The hose will let you adjust the camera as much as you want and is rigid...

Have 7,2 cm of space between the circles. I hope this help other people. The original camera and the rest of the parts are here: https://www.prusaprinters.org/prints/3407 The original remix is:...

I've taken a remix of https://www.thingiverse.com/thing:2833311 to guarantee sufficient space for the new angled fan shroud on the Prusa i3 MK3. Print all components except the arm from [the original](https://www.thingiverse.com/thing:2833311), then...

The idea for the slot mount is from this print: https://www.prusaprinters.org/prints/4112-raspberry-pi-3b-case-for-mk3-v-slot/commentsYou know your printer best and therefore I'm not supplying any G-Code files  ;-)Note: I prefer my prints to...

hello, i made this cause i upgraded my raspberry pi camera. i liked the mount i was using but there were none like it. so i made my own. my new camera can be found here:...

I wanted to use the amazing support from https://www.thingiverse.com/thing:3114849 to be able simply to use the Raspberry Pi with an Arducam IMX219 camera module camera as surveillance camera. So I remixed the raspiCamCover_NoLense file and...

I built an enclosure for my Raspberry Pi Octopi server to secure it to the PSU of my Prusa i3 MK2. The design also allows space for a DC step down converter, which enables me to power the Pi using the spare 12v connection on the i3's PSU. ... This...

Inspired by https://www.thingiverse.com/thing:2843889 I used the one linked above for the Pi3, but needed an upgrade for Pi4 and decided to use a noctua 40x10 fan, as the new raspberry runs a little hotter. This can be mounted on any side of the...

Inspired by https://www.thingiverse.com/thing:2843889 I upgraded my Pi4 from the original Pi3 setup with a new noctua 40x10 fan since the raspberry runs hotter now. This adapter can be mounted on any side of the MK3 or MK3s printer and I chose to...

Inspired by https://www.thingiverse.com/thing:2843889 I used the one linked above for the Pi3, but needed an upgrade for Pi4 and decided to use a noctua 40x10 fan, as the new raspberry runs a little hotter. This can be mounted on any side of the...

It's specifically designed for the Prusa MK3 Lack mod. STEPS • Print the part with the open end facing towards the heatbed. • Push it all the way into the left corner of the metal carriage underneath the headbed. • Secure it with a zip-tie after...

The cold air flows into the housing at the bottom and is extracted again at the top when it is warmed upGood cooling of the Raspberry Pi and Einsy regardless of the temperature in the printer enclosure (fan needed)The 50mm supply air pipe is screwed...

... objects. ...For all the others i send back to the original one.</p><p>For any question please send me a message o write a comment! :) Check out also my side drawers for Prusa:https://www.prusaprinters.org/prints/77095-side-drawers-for-prusa-mk3s

The Raspberry Pi 3 A+ case is designed to be mounted directly onto a 30x30 extrusion without any additional screws, offering a snug and secure fit. Mounting the case isn't excessively rigid, but it performs its job surprisingly well. For optimal...

Raspberry Pi 3 powered off printer's 24 volt power supply (via a buck converter). Plenty of room to stack HATs on the Pi. All tucked neatly behind the frame.</p> <p>The buck converter is a common Chinese model (from more than one vendor on...

I love the pi camera mount (https://www.thingiverse.com/thing:3114849), but noticed I was getting some light bleed in from my enclosure's overhead LEDs, so I remixed the camera cover to add a hood.

This is a case for the PI camera with fisheye lens and IR light https://www.amazon.co.uk/MakerHawk-Wide-angle-Automatically-Day-Vision-Night-Vision/dp/B07DRH5Y5S REMIX from https://www.prusaprinters.org/prints/3407

This is a prime opportunity to deploy the PI camera with fisheye lens and IR illumination, perfectly suited for capturing wide-angle footage automatically, both during daylight hours and at night when night vision takes over.

... one is strong enough to not get a wobbly camera. ... Camera can pan and tilt. You will need a nut and bolt (M5) or similar. Mount is GoPro compatible, I used this thing for my HQ pi Camera https://www.thingiverse.com/thing:4541773 Used Fusion 360

This is a case for the PI camera with fisheye lens and IR light https://www.amazon.co.uk/MakerHawk-Wide-angle-Automatically-Day-Vision-Night-Vision/dp/B07DRH5Y5S REMIX from https://www.prusaprinters.org/prints/3407

I needed a stronger X-Axes camera holder than the ones available, this one is strong enough to not get a wobbly camera. Camera can pan and tilt. You will need a nut and bolt (M5) or similar. Mount is GoPro compatible, I used this thing for my HQ pi...

Remix of the top case from https://www.prusaprinters.org/prints/40277-raspberry-pi-3b-case-for-3030-beam-octopi to allow for more cooling.&nbsp;rpi3-top-Grid - simple holes, accepts the cable guiderpi3-top-Fan30 - mount points for a 30 mm fan. ...Cannot...

Screws:4x same that come with the case2x M3x10, I had some to spare from Prusa build, maybe M3x8 would work also This replaces the bottom aluminum part, which does not do anything anyway… Might be a good idea to add DC-DC convertor and instead USB...

... that was 5mm taller to grab onto my logitech webcam. ...This worked perfectly. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: Yes Resolution: .2 Infill: 15 Filament: Prusament PETG Orange Category: 3D Printer Accessories

Hello there, I'm searching for a spot to install my Raspberry Pi 3 on my Geeetech i3 Pro but couldn't find anything on thingiverse, so I thought to give making a remix of an other case a try. So here it is!! It's my first attempt at designing (or...