raspberry dac 3d models

This is a case for Raspberry Pi ( https://amzn.to/2ReJHj4 )* with DAC Hat ( https://amzn.to/2KfJj3b )* The cap is fixed by 2x M3 screws. The Pi can be sticked with M2 Screws without modifications. If you want to use M3 you have to enhance the...

This is an enclosure to build a Raspberry Pi-based DAC system running moOdeAudio (https://moodeaudio.org/) with analog vu meters and infrared remote control support, to be connected to a Hi-Fi system. Parts that need to be printed: 1x top plate 1x...

Cases for Raspberry model 1, Raspberry model 1 with Hifiberry dac board and Raspberry model 1 with Hifiberry ext dac board.

... Dac+ soundcard perfectly in the top part. This print does not need spacers between the HifiBerry card and the Raspberry Pi, it is a tight enough fit, and the headphone jack actually just fits into the corresponding hole, providing a stable fit.

Design based upon the Nanosound DAC case STL file https://github.com/nanomesher/Nanomesher_NanoSound/blob/master/stl/NANODAC_CASE_with%20AMP.stl I found that it didn't fit the Nanosound DAC and RPi very well. The IR receiver fouled and had to be bent...

For this version, you can use the same screws included with IQAudio DAC+ kit. ...Original version needed longer screws to attach raspberry pi board.

For this version, you can use the same screws included with IQAudio DAC+ kit. ...Original version needed longer screws to attach raspberry pi board.

Just a top case to enclose a rpi with hifiberry DAC+. No screw needed. Slim fit. For base of the enclosure check remixed thing. ...

This is a case for the Raspberry PI Zero W and a PCM5102 DAC module.

This is a two-part case for a Raspberry Pi Model 3A+ with a Raspberry Pi (IQaudio) DAC+ designed to assemble with brass standoffs and machine screws, although the case snaps right together and will probably hold the electronics well enough without...

UPDATE: WiFi only version available print SqueezePiHiFiBerryCase_Outer_WifiOnly.stl and SqueezePiHiFiBerryCase_Outer_WifiOnly.stl instead This is an enclosure for a Raspberry B+, Wifi dongle and a HifiBerry DAC+ hat. You have to unsolder the...

This is a case for an old Raspberry PI 1B with an audio DAC. I created this case because all Raspberry PI 1 cases I found did not provide a clean design and left the SDCard accessible directly from outside. ...I'd prefer to have it integrated into the...

I have made the clearances tight, shouldn't be a problem for Raspberry Pi but you may need to tweak the hole placement for your DAC in the FreeCAD file. It's tweezers to get he SD card out if you are using the Pi 3 A+. I used 11mm M3 standoffs...

This is my first project, a case for a Raspberry Pi 2B and a HiFiBerry DAC+ Pro. The uploaded lid does not contain my personalization that can be seen on the photo. ... Project details can be found here: [Blog post on...

Boite pour Raspberry PI 4 et carte HifiBerry DAC+ DSP. Il n'existe pas de boite pour cet ensemble. Pièces nécessaires : - 4 entretoises de 12 mm (M2.5) - 4 entretoises de 8 mm (M2.5) - 4 vis M2.5 - Colle prise rapide Dans un premier temps il faut...

UPDATE: WiFi only version available print SqueezePiHiFiBerryCase_Outer_WifiOnly.stl and SqueezePiHiFiBerryCase_Outer_WifiOnly.stl instead This is an enclosure for a Raspberry B+, Wifi dongle and a HifiBerry DAC+ hat. You have to unsolder the...

Case for Raspberry Pi Zero W made in 3mm acrylic to contain the pHat DAC of Pimorini. It has a button to turn off the Raspberry Pi that must be connected to pin 5 (for example) and to ground. If you use the Volumio player, you can load the plugin to...

A simple case for a Pi Zero/JustBoom DAC Zero. ... Top and bottom lid are the same.

A simple case for a Pi Zero/JustBoom DAC Zero. Top and bottom lid are the same. Print instructionsCategory: Electronics Summary A simple case for a Pi Zero/JustBoom DAC Zero. Top and bottom lid are the same. Print Settings Printer Brand: Monoprice...

Case designed for a Raspberry Pi2 + HiFiBerry DAC shield. ... i run volumio.org on it thanks UltiArjan your base work

A remix of the HifiBerry Case by Stamos (https://www.thingiverse.com/thing:4208854) to fit the Allo Boss I2S DAC (https://allo.com/sparky/boss-dac.html) for Raspberry Pi 4.

... To assemble you will need. * 1 x Raspberry Pi 4 Model B * 1 x PCM5102A I2S DAC made by North Flat Japan * 1 x 5V DC Fan * 5 x Jumper Wire Female to Female * 4 x M4x8 Pozi Pan Head Machine Screws. * 4 x M4 Hexagon Nuts. ... * 4 x M4 Washers.

I found it difficult to design a closed case for Raspberry Pi , considering there are plugs on three sides. The project will be more complicated when you need to add extension boards. So I try to keep things simple. It is an open design with 2...

This is a remix version of the Honeycomb Case sled fitted with holes for the Hifiberry DAC+ Its quite a loose fit, so maybe a bit of scaling will help. ... This is my first time using CAD, so my apologies if it isn't as refined as it coud be.

The USB cable supplying power to the other USB micro connector on the Raspberry Pi Zero needs to have a quite small USB plug since the USB soundcard is slightly in the way. I trimmed down the connector with a pair of pliers to make it fit. ...A 90...

Designed a case for my Raspberry Pi 2 with Hifiberry Dac+ Pro (RCA outputs). It is a tight fit and therefor does not need screws or glue, but kinda snaps together. Because the DAC tends to get warm I added vents, which also lets the glow from the LED...

You need: 1x Raspberry Pi 4 https://www.raspberrypi.org/products/raspberry-pi-4-model-b/ 1x IQaudio DAC+ https://www.raspberrypi.org/blog/iqaudio-is-now-raspberry-pi/ 4x the stands which are included in the IQaudio DAC+ Kit 4x stands M2.5mm x 20mm...

You need: 1x Raspberry Pi 4https://www.raspberrypi.org/products/raspberry-pi-4-model-b/ 1x IQaudio DAC+https://www.raspberrypi.org/blog/iqaudio-is-now-raspberry-pi/ 4x the stands which are included in the IQaudio DAC+ Kit 4x stands M2.5mm x 20mm 8x...

You need: 1x Raspberry Pi 4 https://www.raspberrypi.org/products/raspberry-pi-4-model-b/ 1x IQaudio DAC+ https://www.raspberrypi.org/blog/iqaudio-is-now-raspberry-pi/ 4x the stands which are included in the IQaudio DAC+ Kit 4x stands M2.5mm x 20mm...

Loosely based on Scharmann's small media player ( https://support.hifiberry.com/hc/en-us/community/posts/201843381-Small-media-player-with-squeezelite-slave?page=1#comments) and using ideas from https://www.thingiverse.com/thing:4632031 --- I wanted...