ran goddess 3d models

Motors chattered, missed steps, ran slow and hot. Set micro-stepping to 16 (jumper on shield). Set voltage on driver board pots to .08 volts. Motors run smooth, fast and cool. Thanks again Thorgal!</p> <p>Control Software:</p> <p>I am using <a...

If I'm thinking of this right, it would produce a “chaser” pattern where the colors follow themselves around (though maybe add more LED's and Hall sensors as above).You should be able to implement this using a through-hole pot/encoder on the shaft,...

The vials I used can be found here: https://www.amazon.com/gp/product/B07FVJZH6D/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&amp;psc=1The next issue I ran into however, was what to do once an hour had gone by and the vial was full of water. This one...

i ran my fan header cable slack, and have the rgb contoller hot glued in the bottom. this should raise the card slot up enough to make it really easy to access. ...will update when i get the part printed and teh sd adapter in the mail.</p><h3>Print...

Then, he was destined to face the goddess of peace Mothra in a brutal confrontation that left him defeated and put an end to his reign of terror. Specifically for this movie installation, talented Yasushi Nirasawa worked out a concept that would...

Goddess of Themyscira is presented wearing the Amazonian battle armour that consists of a hardened corset topped by her signature golden eagle and a layered armoured skirt that are held together by a double “W” insignia belt. The 3D artist made sure...

Technically, the house ran City of Sonora water, but only because it was pumped up the hill from Lyman's house at the bottom of the hill. Basically, you had to open a valve at Lyman's house, wind two bare copper 220 wire leads together by hand (that...

The enclosure width is now 450mm, still wide enough to hold an ender3.Frame assembled (upside down until I get the skirt corners and feet installed):(finally got my ducks in a row and built the frame *badum tish*)To further increase the frame...

Printing them at 60% scale in the original split pattern is highly ill-advised and I am just gonna throw that WARNING out there right now due to the nightmare support situation I ran into trying to do this. So for those of you trying to small scale...

If do you need to get the lock back off, the best way I found was to stick long allen keys into both of the lock's holes and then pinch them together to lever the lock slightly apart, which reduces the pressure enough that you can wedge a thin...

I then ran some tests at 40C to see what impact they would have. I decided to keep the temp low as my intent for the dryer is actually a low humidity spool holder/feeder. I also wanted to ensure that the spool holders were not impacted by excessive...

Chase the threads with a 1/4-20 tap after printing in case any glue ran into the threads. I print with a 0.4mm first layer and 0.2mm subsequent layers, so I need to pause at layer 30. If you print ALL layers at 0.2mm you would need to pause at layer...

I used 24V LED lighting in my cabinet and ran the 24V leads through some 1/2" split loom into this plate. Apply sealant around the leads inside the cabinet where they come through the plate. Re-use the screws that held the HF box on. (supports...

Here's an screenshot of the test run results: As you can see, the SMuFF (9 materials version) ran for about 12.5 hours and has accomplished over 3000 tool changes. In an normal print that would equal a model with 600 mm in height with one tool...

Then restart OpenSCAD.4) OpenSCAD won't pick up newly installed fonts in C:/Windows/Fonts.In case new fonts are missing, put the font TTF files also inC:\Program Files/OpenSCAD/fonts/Liberation-2.00.1/ttf and restart OpenSCAD again.&nbsp;The names...

In my builds I ran both the thermistor and fan cables down the left side.[ ] Mount the thermistor to the brack on the left side of the blower fan. I have three dryers and there were different thermistors in all three so I designed the bracket to...

Certainly, the larger inner cone diameters will result in a lower rotor weight in the center which may also help it to spin easier...Assuming the default 5.1mm inner cone rotor diameter was already tested, I would next test the 5.6mm inner rotor...

I'm going to try and explain some of the issues I ran into, so that you can avoid them. I think most of those issues are related to my printer, so hopefully you have even better success!</p> <p>First, a few general comments. Some of these parts have...

The (no longer) strongly recommended three parts can be printed individually via: Siren_Whistle_Mouthpiece.stl Siren_Whistle_Rotor.stl Siren_Whistle_Horn.stl I ran some additional tests. I checked both the alternate horn and and BbrnKyle's original...

I was sorry for him, but it was not a thing you could do anything about, because right away you ran up against the two stubbornnesses: South America could fix it and he did not like Paris. He got the first idea out of a book, and I suppose the second...