ramp model

This seems to be a weak point in all reciprocating saws and is a particular problem with this model, with some users reporting that the blade clamp had sheared off after only relatively light work. Replacement parts are available, but at a...

I based the design of these pieces off of the Ender 5+ model available on GrabCAD (https://grabcad.com/library/creality-ender-5-plus-1). There will eventually be a detailed pdf showing a build guide, confirmed material list, building and flashing...

There seem to be quite some error margin in production, if your model is a bit too big to fit, just sand off maybe .5 mm from the sides to make it fit.Completely(!) remove any filament remains inside the two enclosure parts.Fit servo into upper half...

Depending on how well your models adhere to the print bed, you may need a brim/shaft/skirt to increase adhesion. In principle, it should be printable with any 3d printer, as I printed mine with my old Anycubic, which was about to break down...

Nixie_ldl_clock IN-12descriptionGitHub project repository:https://github.com/lorenzo-dl/NIXIE_LDL_CLOCKNixie tubes are a vintage type of display that uses a glass tube filled with a low-pressure mixture of Neon and other gasses like Argon.Inside the...

 900mm in length (shown in the picture is a bit too long, you may want to use 800mm instead)The bamboo skewers seems to come in different sizes, so use the file that closest match the skewers you have and scale the model accordingly.  If...

One intersting thing I probably should have done, is just print the columns on the platforms, would have saved some time, and the hardest assembly step. Next Acquire the Electrical components: Electrical Components Post Printing is very involved,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

The “NANO 1” model follows (support for matrix / hemera already published). in addition to the name and logo (grant it to me) they share the same "SUPPORT BASE" component as a fixed base, and with the quick release (only 2 screws) to adapt in the...

Bill of Materials ================= 1x Arduino Mega or clone (actually an Uno would suffice for the current version, but wouldn't leave much room for future improvements, and besides, I already had the Mega ;-)) 1x 20x4 LCD module (HD44870/SC2004)...

If you need a lot more room (more than a few mm) you may need to update the model to scale it appropriately. (~$1 of filament)</li> </ol> <ol> <li>Light string or rope. Cut it about 5ft 6 inches, or just enough to make a loop on the elbows, running...

... other people might actually make! Haha. This was made with TinkerCAD. This is about as advanced as I get when it comes to CAD or 3D modeling at all. I'm very much an amateur with this stuff. ...That said I'm really happy with how it came out.

I checked with Meshmixer and the model is fine. Tried re-exporting from F360 to a new file and experienced the same issue. I opened a bug report, but Ultimaker closed it as not being able to duplicate.</strong></p> <hr/> <p>The case is designed to be...

Downloaded some Radio Control model yacht designs. Non of them suited my fancy for building, so I decided to come up with my own. Main Desing principles... No Keel! -> Surf Board / Windsurfer style. Light Weight (relative to size of jib!) ...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8...

If you don't want to mess with a PLA support, you could probably print this part in two separate objects.I provide you the Fusion 360 file, so you can customize and change the model according to your rail system. I strongly recommend you to...

The retainer is up higher than need be in the video for safety.--------------------------------------------------------------------------------------------------------------All parts printed in PETG, with standard Voron settings for rigidity.0.20...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

If you want it without internal battery, I have designed this same model without the hole for the battery, remaining in measurements of 126x51x35mm, you have it here: https://www.thingiverse.com/thing:6016310 Required Components: - 1u Mini ZVS...

NOTE: Newest v2.0 of this model is now available - click here.NOTE: This is v1.1. If you were looking for v1.0 - click here. Note: As of Nov 16, 2023 — in addition to the earlier remix changes, today I added SVG files for engraving the plexiglas...

# Introduction This is a remix of the Ender 3 HallON v3 Installation kit to fit a Micro Swiss Direct Drive set-up (recent models with additional screw holes on the left. Because I noticed that the hold of the sensor in the adapter gets loose after...

No support is needed and would be very hard to remove because the support would be inside the model where the magnet eventually slides into. We are depending on bridging for the parts that would normally need support. I have given extra tolerance...

It can be thrown whole into a filament dehydrator to refresh the packets, without worry of warping. Assembly: Attach the bearings to the end of the rollers and snap them into the slots in the base (Optional, Glue them to the spindle so they won't...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 0 stencil_drawing =...

(In the future, I'll model a printable screw-gun interface for people who can't get the part in question.) 4.#6-32 brass nut, 1/4" across (measured face to face), 3/32" thick (optional) McMaster-Carr 95130A120. Fits into a pocket on the gun carriage,...

You may need to adjust your switch's orientations in the holes depending on your model of keyboard switch, so be prepared to work through that. 13) Lay in the keyboard-switch-populated 3D-printed piece so that the pins face towards the inside of...

---------- # STP FILES Again I included the STP files, so that everybody with a decent 3D CAD can load the volume models. ### The thread test STP In this file you find a test screw (with the nominal threads) which is identical to the spindle...

The “NANO 1” model follows (support for matrix / hemera already published). in addition to the name and logo (grant it to me) they share the same "SUPPORT BASE" component as a fixed base, and with the quick release (only 2 screws) to adapt in the...

Specifically, the mouth utilizes inexact measurements, and inconsistencies in source models from the 3D printing process made it difficult to gain a good measurement. On the sketch, we measured the mouth to be 1.20cm from the side of the constraint...

The Tunnelplan Wind Turbine is a 1:10 scale model of an existing wind turbine. The diameter of the rotor is 2000 mm (20 meters) and the tower height is 1200 mm (40 meters). the max.ceiling height inside the house. Solution 4 energy...