raiser 3d

This is a very simple cross-hatch for raising plant pots above the floor of their containers. Depending on your slicer you should be able to adjust the X, Y, and Z dimensions to fit your container and raise the plant pot to your desired height. ... ...

Easy print, works great if you dont want Helmer to move when you open your drawers!

<p>I was pretty annoyed that my routed cables were being squished between my table and the printer frame. ...That's why I designed these extenders for the rubber feet in order to elevate the printer by 28mm so as to no longer squish my routed...

A simple thing to rais the inner plastic thing in which the flower in plantes in the actual pot. ... Can be printes without supports.

Pretty straightforward stuff to lift that massive tower and get the hoover out from underneath. The part needs to be robust enough to handle the weight of this thing. I employed a trick: you can use your standard 0.4mm nozzle and set the extrusion...

I wanted to raise the height of my LACK enclosure by 10mm to allow air flow under the sides and give the Bowden tube more space before hitting the enclosure.

Print it with 10-20% Infill Update: I have updated some small und big stuff. ... There is now an small offset from the Top Part (Oberseite.stl) and also i have raised the Bottom Part (Unterseite.stl) to 50mm instead of 10mm

Laptop stand designed specifically for the MSI GS63VR model, but also compatible with similar systems.

I built this swift Aqara Door Switch lifter to align the sensor perfectly whenever it's installed in a door frame on a door.

<p>The mug adapter for the couch console sits a little bit to deep in the snack cup. ...So i made this adapter to bring the mug adapter higher, allowing it to grap the mug handle way easier.</p><p>&nbsp;</p><p>Added V2</p><ul><li>This version is 1mm...

Rev Guard test

Sometimes you just need to go higher with the printer. That's what this gadget is for. ...Of course, it is fully compatible with the original legs and anti-vibration pads.

<p>Print in Carbon Fiber or other heat resistive material.</p>

When constructing a custom KongKong ET frame, it's often necessary to allocate additional space within the canopy area. One viable solution involves employing M3 inserts to securely fasten add-ons directly onto the frame itself. ...Additionally, three...

<p>I needed a bit taller version than the original. ...&nbsp;Couldn't quite fit my under bed storage boxes.</p>

The gas pedal on my Ford Fiesta is really tough to reach for heel-toe shifting. This modification relocates the pedal upwards by 2cm and shifts it towards the brake, making it more accessible. I printed it with 75% infill using PLA. So far, the part...

<p>This plant pot gadget lifts your pot about 1cm from the ground. Water will run out better and air gets better to the roots. This makes a healthyer plant :) siutable for many plantpot sizes!</p> <ul> <li>measure across the bottom of the with of...

Ikea-style LATT tables and chairs are available for printing. ...I've posted 80mm and 55mm versions of the designs, which can be successfully printed at a resolution of 0.3mm.

I built this custom leg extension to elevate my Ikea table, giving me ample space to construct my Ender 3 in a sturdy case. The table is now raised approximately 120mm. I found that an infill percentage of 10 and two wall lines were more than...

This device is designed to lift a coffee table up just enough to trigger our robot vacuum bumper, forcing it to turn around rather than attempting to navigate over the legs and get stuck. ...It's 17 mm in width, making it compatible with most standard...

A basic yet sturdy spacer designed to elevate the laptop's back, optimizing air flow. To assemble it effectively, follow these steps: It's originally made for a polycarbonate MacBook with a 22mm height, but you can easily customize it if...

Remixed for the AOC 32 inch model with a base of 15.5cm

Needed to Raise the seat 6cm, TPU , Gyroid 10% infil

My cell phone needed a little bump up to get a better viewing angle so I made this little spacer since I couldn't find one already Added a 4 bolt as well

raise your T14

Raises the seat inclination of the **IKEA HAMMARN** Sofa by 5°. Printed with **PLA** at **10 % cubic infill** it can easily hold a 70 kg person. ... If printed with **100 % infill** it should support over 300 kg but **use at your own...

This device attaches to the back of the Ergodox-EZ stand, elevating its overall height.

A Tri-rail accessory designed specifically for Picatinny rail systems elevates the firearm's attachments.

Small decorative dish designed specifically to hold and display your dog's water bowl in style.

This model is engineered specifically for LO206 racing, and both versions adhere to the 2020 competition regulations. After printing, carefully inspect the dimensions to ensure they remain below 3/4 of an inch. ...To secure the part in place, you will...