railcore ii 300zlt 3d models

... with the Magnum pulleys. * Tentative confirmation of compatibility with the [713maker Halo](https://713maker.com/railcore/railcore-ii-300zl-halo) * Slight update to the usage instructions. ... 2019.03.17 --------------- * Initial publication

... ...Same issue apply re: clones / off-brands. I have the MRW cover and related cover interface components installed on my 300ZLT which pretty much renders all of the 1515 rail mount versions incompatible.

Adjustment of the drive screw will likely require a ball-end hex key due to tight clearance with the Magnum pulleys. Tentative confirmation of compatibility with the 713maker Halo Slight update to the usage instructions. 2019.03.17 Initial...

LED diffuser assembly designed to attach to the 1515 extrusion of the Railcore II. The assembly is designed for 10mm wide LED light strips that can be cut in 100mm segments. Each assembly dovetails into another so that the diffuser assembly can be...

Remixed/redrew the original mount to fit inside the aperture on the aluminium mounts that come with the Filastruder Railcore kits.

This is a BLTouch version 3 sensor mount for a Railcore II 3D printer. For an E3D V6 hot end, the mount produces probe offset values of X0 Y28.5 Z2.5, which is about as close as you can get the probe to the hot end. It has the advantage that the X...

LED diffuser assembly engineered specifically for attachment to the 1515 extrusion of the Railcore II. This assembly is designed for use with 10mm wide LED light strips that can be cut into 100mm segments. The assembly features a dovetail design,...

Modified [jstevewhite's cover interface for railcore](https://www.thingiverse.com/thing:3569321) to allow the use of a PC4-M10 push-fitting on the inside of the printer so filament could be fed from the outside.

This printable bottom panel serves as a crucial component for the Railcore electronics box, particularly since the panel kits do not include a CNC-cut panel. As a deliberate design choice, this panel acts as a safeguard to prevent accidental...

Anything in the range of 8-12mm should work fine. Print Settings Printer: Railcore II 300ZL Rafts: No Supports: No Resolution: 0.2mm Infill: 40 Filament: Any PETG Any Notes: The bracket includes a 0.5 degree angle on the face bolted to the...

... this fan duct. ...This design is absolutely fantastic but for my Railcore Mosquito setup it was missing some minor details that I just couldn't fix from the supplied STL file. ...So here it is, I hope it help others fine tune their part cooling needs.

These corners feature a revamped design inspired by the Railcore electronics box. ...Instead of relying on traditional fasteners like nuts and bolts, engineers have integrated heatset inserts into every hole, making it simpler to remove panels from the...

This hack of a J Steve White stl enables three spools across a 300 mm wide RailCore by being screwed directly onto the 15mm rail. A hole is included for a filament guide, making it possible to print one standard and one mirrored version. ...This design...

This is a hack of a J Steve White stl to allow three spools across a 300 mm wide RailCore. It is screwed to the 15mm rail and includes a hole for a filament guide. Print one standard and one mirrored. It was specifically designed to allow me to do...

Here are a few mounts to use on the Railcore system with a Nimble. Currently, there's a mount for the V6 and one for the Mosquito hot end available. If you need a different hot end mount, please let me know. Some holes appear to be blind holes,...

This custom backplate secures the hinges of RailCore 2 doors. Initially, I was hesitant about tightening the nuts on the rear of the acrylic panels, trusting bolts within the material to withstand frequent door opening and closing. To alleviate these...

Quick and dirty mount designed to secure the Dyze Design Filament Sentinel firmly to a Railcore 2 300ZL, a setup that will likely work seamlessly on any printer boasting 1515 extrusions. This mounting solution necessitates two M3x8mm screws and two...

This is my E3D threaded heatsink for the Railcore using the volcano hotend. I printed with polycarbonate with carbon fiber, but any stiff material should do just fine. One thing to note, at least for me, to install this you have to remove your fan...

This tool is designed for use with Railcore ZLT, even when yokes are flipped over; it will also work seamlessly with standard ZLT, as it doesn't require bearing holders. The intended print orientation is large side down, but both top and bottom...

This is a mount for the Duet Magnetic filament monitor for the Hemera on a Railcore. The STLs are oriented for proper printing and should not require supports. Where supports are needed I added an integral supports (2) that need to be removed after...

Steve White's hinges for the Railcore 2 ZL/T printers, serving as printable hardware for Acrylic doors designed by Mandala Rose Works. If you have 3mm (1/8") doors, print the 3mm hinge; if your doors measure 6mm (1/4"), use the 6mm hinge. The STL...

I figured I'd design a hermera (with Volcano hotend) mount for the railcore. All of the parts with inserts are designed to be used with M3 inserts with a 5.15mm OD (https://smile.amazon.com/gp/product/B077CJV3Z9). If you want to modify this design...

This is a load spreader for the hinges of the RailCore 2 top cover backplate.\r\nI was not thrilled about tightening nuts on the back of acrylic and relying solely on bolts in acrylic to withstand constant opening and closing of the enclosure, so I...

This is my precision-crafted E3D threaded heatsink tailored specifically for the Railcore using the volcano hotend. I utilized polycarbonate with carbon fiber, but any stiff material will yield impressive results. I've uploaded the step file and...

Once installed, the top is just a box with outside dimensions equal to your railcore, less than 7mm thick walls, making it suitable for 1/8", 3mm, 5mm, 1/4", 6mm, and other thicknesses that should work fine. And yes, I know there's debris in the...

PrusaSlicer sacles the svg internally to fit the size of the bed and on a Railcore, the correct bed size appears to be 315X300 with the origin at 0,0. To verify that the bed size is correct, place the 300mm X300mm stl on the bed as if it is to be...

PrusaSlicer sacles the svg internally to fit the size of the bed and on a Railcore, the correct bed size appears to be 315X300 with the origin at 0,0. To verify that the bed size is correct, place the 300mm X300mm stl on the bed as if it is to be...

It works exceptionally well and provides an ideal solution for mounting it to an extrusion on the Railcore printer. I personally prefer to store my filament rolls inside the printer itself, ensuring that the filament feeds directly up into this mount...

This is an alternate electronics box corner for a Railcore 300 ZL/ZLT. This version has a place for a captive nut for each screw, and is designed to print without supports. There are also slight modifications so that all screws can be M3 x 10mm. ...

This is a base for the Duet Magnetic filament monitor that fits perfectly on a Hemera on a Railcore. The STLs are carefully designed to ensure smooth printing and don't require any supports, unless absolutely necessary. In those cases, I've added two...