radiomaster t16s 3d models

Mount for Dragonlink slim as used on Jumper T16/T18 or RadioMaster TX16S. Must be used with the solid handle (not the folding version) on the Transmitter Printer two of the brackets and one box. Use two 3mm socket-head cap screws with lock-nuts. ...

... O.D. ...standoffs and a 19mm rear spacing). Other antennas (e.g. Radiomaster, etc.) have a larger balun housing and will not allow this mount to close over it. ... Use heat shrink or superglue to hold the mount closed after antenna installation.

These folding TPU mounts are designed to attach the Radiomaster RP1 antenna onto the standoffs of your kwad. The required standoffs for these mounts should be M3 size with a diameter of 5mm, and the distance between the two standoffs should be...

... and one with a 30 degree uptilt. Works with SMA pigtails without the mounting tabs.I'm planning on making one that fits the thicker Radiomaster antennas as well, but this is what I have for now. ...Feel free to remix for whatever antenna you use.

Remixed the original for tighter fit on my Radiomaster TX16S There was a little play around the sticks and the base of the gimball. Now the holes for the sticks are 7.96mm and the base is 49.4 mm v3 For the V4 I added 1mm over the switches and the...

This is a gimbal stick end meant to be used on R/C transmitter radios with M4 (4mm) gimbal stems like the RadioMaster TX16S. Prints in two pieces that are glued together after printing. Fits onto the stock stems rather easily with very little...

Since I like to watch the world burn I purchased a 5000mah (2 x 21700) Li-Ion battery from Radiomaster to put in my Jumper t16, fits perfeclty. I really liked the idea to have an "external" power supply for my crossfire even tho I never actually used...

This is a Case for DIY Projects using the JR-Style module bay in radio transmitters such as FrSky, Radiomaster, ... As contacts I used a usual pin header (as shown in the picture). It can be printet without support one usecase would be as a...

This is a Case for DIY Projects using the JR-Style module bay in radio transmitters such as FrSky, Radiomaster, ... As contacts I used a usual pin header (as shown in the picture). It can be printet without support one usecase would be as a...

... Then when the landing gear are raised the patch antenna is in a vertical position and facing down. This could also be used for the smaller patch antennas for the FrSky receivers and the Radiomaster R168 receivers using the FrSky patch antennas.

This spacer is used to attach the RadioMaster AG01 aluminum gimbal to the Jumper T20 transmitter.A 3mm wide tape LED can be attached to the back of the gimbal for fancy decoration.Since the gimbal is retracted, the back of the gimbal and the dial...

Edit it online https://www.tinkercad.com/things/7XMXASqEGrIWhile waiting for my new Radiomaster TX12 radio, I wanted something that I could use to use as a controller in a drone simulator. ...While less than ideal, an XBOX 360 controler is easy to...

... to size. It's a bit smaller than the clips on non-DIY modules (such as the crossfire module I have), to allow for 3D printer tolerances. I don't know if it was a problem only with the Radiomaster TX16S, but it now is compatible with it. ...Enjoy!

Print: 1x PLA Base 1x PLA Cover 1x TPU Base-V2-Walksnail 1x TPU Antenne1 1x TPU Antenne TBS (Iflight A85) 4x Spacer1 (Under Walksnail) 4x Spacer2 (Under AIO Board) Print Settings Base: PLA 5x Outline 100% Infill Screw: 3x M2x25mm 2x M2x18mm 2x M2x4mm...

I designed some brackets to mount the Radiomaster AG01 gimbals in the DJI FPV Radio controller. I uploaded tow versions, with the no cut version, there is no need to modify the DJI Radio. For the normal version, you need to cut the ring (where the...

... I used the anchoring system that Stevensbox designed for the OpenRacer. The mount anchors between the bottom plate and top plate of the quad and extends posteriorly. At the bottom of the mount, I am double taping the RP1 Radiomaster ELRS antenna.

-EMAX drone engine 2400kv-Geprc AIO Fc 20A-HQProp T5.1x2.5x3 -Tattu R-Line 850mAh 14.8V 95C 4S LiPo-RadioMaster R81 Nano -D8 FrSky SBUS Receiver-Caddx Ant (16:9)for more information or questions visit: www.dutchdroneworks.com or send an email to...

... Everything that is printed in black are final form. Flipsky 6374 motors FLIPSKY Dual Mini FSESC6.7 ESC Mateksys F765-Wing flight controller running ardupilot Crossfire RX Radiomaster TX Files will be posted soon. ...as this is a work in progress

I wanted my Radiomaster TX16S to look sleek and minimal with TBS Crossfire Micro TX V2 module so I designed this thing - a Tango 2 style antenna. Will probably fit every radio with stock 2.4GHz antenna. Antenna's case consists of front part, back...

I have redesigned the rubber insert to fit smaller handle diameters (based off of my RadioMaster TX16S handle without the grip add-on)! Fits tightly inside the monitor holder with a cutout to allow easy attachment/removal. I printed mine with...

Dedicated case designed specifically to be mounted without battery to the Radiomaster TX16S or Jumper T16 transmitter, powering the Eachine RD200 FPV DVR monitor directly from the transmitter's power source. Print all components including the case,...

Radiomaster TX16S antenna plate for a long range 8db 2.4 Ghz antenna. At the same time making the antenna removable in case you want to replace your stock antenna. I made it so that it's easy to print with a flat bottom. It wil take the slight...

Remixed the original for tighter fit on my Radiomaster TX16S There was a little play around the sticks and the base of the gimball. Now the holes for the sticks are 7.96mm and the base is 49.4 mm v3 For the V4 I added 1mm over the switches and the...

... Those need post processing by cutting the thread with a thread cutter. A little more work, but usually better results for a smooth and precise fit on the gimbals. Fits most FrSky radios, Radiomaster TX16S, Jumper T16 / T18, Devo, Spektrum, etc.

-EMAX drone engine 2400kv-Geprc AIO Fc 20A-HQProp T5.1x2.5x3 -Tattu R-Line 850mAh 14.8V 95C 4S LiPo-RadioMaster R81 Nano -D8 FrSky SBUS Receiver-Caddx Ant (16:9)for more information or questions visit: www.dutchdroneworks.com or send an email to...

Radio Stick Ends for Radiomaster, AG01, or other M4 gymbals8mm dia x 20mm overall hieght (15mm texture)This is a file for high resolution resin ptinting. It has an interal M4 thread. One of the files has a flush tube, which I used to wash out the...

Designed for the RadioMaster TX16S Mk I with Hall Gimbals. The protector snaps onto the sticks. The top switch protector attaches to the gimbal protector via an M3 screw at least 10mm long. The conical interior tends to push the sticks toward the...

(Waiting for Radiomaster TX16S, so I'll modify it also for that since Radiomaster has a non-removable, bigger antenna.) It's made by 2 parts, so you don't need supports and can print easily. You need: 1x M3x10 mm screw 2x M3x60 mm screws 3x M3 nut...

This allows the TU2 module to be operated with remote controls such as TBS Tango2, Taranis-X-Lite and probably Radiomaster Zorro.The module housing and the full-crossfire adapter from P. Seidel have to be connected with super glue.<br>Wiring...

Replacing the original antenna in the Radiomaster TX16S with a SMA to UFL cable, and using this holder to install it seamlessly. For detailed instructions, visit https://oscarliang.com/tx16s-removable-antenna-mod/. The process is straightforward and...