radiomaster t16s 3d models

Friction fit and stops at 45. PETG, no supports required. Requires replacing the handle screws with M3x12 to fit the kickstand and factory handle. The square on the bottom was intended for velcro to hold the kickstand in, but the fit is tight...

Evening All. Not sure why my version of these files (https://www.thingiverse.com/make:834086) are no longer visable, so I have uploaded them again now. Thanks to the original designer for sharing the STEP files, as I wanted to make some slight...

This is my original design for the TX12 radio by radio master, it is to replace the stock rear handle, no extra parts are needed, will fit only the TX12. ...I have not tested it with modules in the back although I believe I left enough room, if not I...

Inner diameter is 15mm to help fit thumber stick ends The stick and stick ends in the picture are roughly ~30mm tall from base The naming on top can be customized or if you need a bigger or taller gimbal protector feel free to contact me

Hi all, last night i created this extension. I will use my radio for anomatronics and need easier access to the s1/s2 knobs. I know the knob holes are a little tight, but since its printed, just soften the whole a little with a lighter and it will be...

5' screen support for T18 jumper which must be compatible with the TX16S radiomaster because they have the same base. compatible with an fpv screen at 25€ on bangood. ... unaffiliated link Ecran 4.3'

This is a designed stick end originally M3 screw for Taranis X9 Lite. ... I made the screw space M4 to fit for other TARANIS, JUMPER, RADIOMASTER RADIOS GIMBAL STICKS

Car control body/housing/shell for Radiomaster Zorro Radiomaster Zorro has relatively compact main board (with separate secondary control boards) compare to Taranis Q X7, thus it is possible to design more compact remote control. As the matter of...

... on using the hook. They are made to go deep into the gimbal for people that use the round LEDS or the additional spacer designed for Radiomaster TX16s, MK2, MAX with 14mm lotus sticks or 10mm AG01 Sticks. print with supports in PLA. ... enjoy

... For further details or to ask questions, please refer to my blog on RCGroups at: https://www.rcgroups.com/forums/showthread.php?3643743-DIY-Slider-upgrade-for-RadioMaster-TX16S If you notice any issues that need adjustment, please let me know.

The receiver Radiomaster R168 has analog input pin for telemetry monitoring battery voltage (up to 18V). Next the battery pin are also other connectors (S.bus, S-port, RSSI). Plug the battery voltage pin into wrong position will probably damage the...

For Radiomaster user to modify the antenna placement. I had remove the stock antenna and hide in the radio body. Remix one of the antenna holder from thingiverse to hold the TBS Mircro module V2 antenna. ... Just do a cutting at anyplace to slot in...

For more details, check out the thread on RCgroups: https://www.rcgroups.com/forums/showthread.php?3640501-Radiomaster-TX16S-Flexible-Quick-Lock-Release-Stick-Protector. Note 1: The included parts won't work with the T16/DX9 version. Note 2: You'll...

Print in TPU.Simply remove the rod from the Radiomaster Pocket's antenna to seperate the original baseplate, slip this print where the old base used to be, re-insert the rod, and place this where the old antenna mount used to be! ...My original mod...

Transmitter tray for Radiomaster TX16S and TX16SMKII Designed in order to improve transmitter handling Easy click in system for all parts, no glue required Easy transmitter plug in and fixing New Version V2 included -Now suitable for mounted...

Car control body/housing/shell for Radiomaster Zorro Radiomaster Zorro has relatively compact main board (with separate secondary control boards) compare to Taranis Q X7, thus it is possible to design more compact remote control. As the matter of...

The large Radiomaster Ranger module made the original handle a bit useless. I've been using the original design og foldable handles https://www.thingiverse.com/thing:4283408 designed by dwc_kolenbrander . But they are not compatible with the Ranger...

This case is made to fit the Betafpv Micro ELRS 1W Module onto the Radiomaster Zorro. You will still use the original top cover with the lcd. If you only have the electronics and need the top cover, betafpv has the stl available on their website. ...

Remixed the great Radiomaster TX16s gimbal and switch protector from [Piero Menetti](https://www.thingiverse.com/thing:4751111) to make them fit my TX16s using Lotus stick ends and gimbals which are set a bit higher. The bottom gimbal protector...

These are just two 'horrible' functional remixes made by chopping and adapting two convenient sources, in order to mount an Eachine Moneagle to a Radiomaster TX16S that has its handle reversed (in order to fit in a certain storage/carrying bag from...

EdgeTX, a modified Firmware and a Radiomaster TX16 touch enabled screen make it possible for the FrSky Horus X12S radio transmitter to also have touch functionality.The increased thickness of the touch enabled screen though makes it necessary to...

I wanted to make a mount for my new Eachine Moneagle 5 FPV display that can be mount easy on RadioMaster TX16S. I have found excellent Go Pro style mount for smaller display on link https://www.thingiverse.com/thing:5321464, so I have use it as...

I was inspired by the Radiomaster Tx16S Rear Grips design and wanted to use them on my Jumper T16, but since the fitment of the holes and the height of the Back Cover differed, I had to adapt them to fit correctly on the Jumper T16 and got them to...

This is an antenna mount for the Cherry CADDX Vista antenna and the standard Radiomaster T style 2.4GHz antenna for the Five33 Switchback HD. Will work for diversity and non-diversity setups.PRINT IN THE PICTURED ORIENTATION W/ SUPPORTSI also...

Due to this I wanted to print a mount which will allow me to attach my 4.3" FPV monitor to my Radiomaster Zorro to fly FPV. I found the design from vlajanec which looked great though relied on long M2 screws to attach to the Zorro. For some...

### Lithophane I embedded the Radiomaster logo as a lithophane for the status LED. This does a reasonably good job of diffusing as well as letting light pass, at least with my (random brand that even I don't know) filament. If you use a straight...

I have tx16s before and its have a spacer, cant fine same thing for boxer so i crate one.Use small piece double sided tape to secure it to the case, because it lower than the battery tray (and not snug fit)

This is a modified version of ndrewrcnewton's knob. I found that the increased friction was good but the center position indent was gone, especially when in use flying. I modified the design to include a notch. What I did was print the knobs then...

A simple mount for mini screens to the tx16. Fits over the pots and is removable quickly. ...Just used some hot glue to attach the screen.

This disc is to be placed between the potentiometer and the scroll wheel. It creates a little drag between the two components. This prevents the scroll wheel from being too light, and selecting the complete opposite thing to the thing you actually...