radiolink ts100 3d models
800 3d models found related to radiolink ts100.
cults3d
Custom designed by Charlie Foxtrot RC Crawlers, Thumb steering for Radiolink and flysky controllers. May fit others as well. ...This utilizes your factory wheel foam as well.
thingiverse
Remo Rocket germobox for Radiolink receiver. ... It should also fit Remo Hobby SMax and Dingo because they have same chassis bracket.
thingiverse
This is a protective shield designed specifically for your Radiolink radio, engineered to work seamlessly with the at9 and at9s models. ...The emblem on this protector bears an uncanny resemblance to the Rotor Riot logo.
thingiverse
This is a GPS Radiolink TS100 antenna mount For an unoriginal XL 7 frame, but it should also fit on the original iflight xl7 frame
thingiverse
Was always misplacing my wheel wrench so I designed this simple pressure fit wrench holder that mounts to the Radiolink transmitter. Its not perfect but good enough to where its useable with no issues. ...I'll be tweaking it slightly at the top so...
thingiverse
Box for TS100 with holders for two arms, the Allen key and a T-stand. Requires two M3x30 screws for the hinge. ... File in FreeCAD is provided.
cults3d
Case for the RADIOLINK AT10II RC radio. ...YouTube video: https://youtu.be/5U05c4_raTY IMPORTANT: For assembly, you will also need: - 2 pieces of pipe (or stick) with 6 mm diameter and minimal lenght 310 cm for make shoulder straps (2D drawing is...
thingiverse
This is a custom RadioLink SE100 GPS Cradle designed specifically for motor mount on a TBS Caipirinha 2 FPV Wing. To accommodate a Caddx Vista VTX in the bay where the GPS normally resides, due to the short camera cable, a new spot was created for...
thingiverse
I own a RADIOLINK AT10 RC radio that I'm planning to power with my homemade field battery, which can be found at http://www.thingiverse.com/thing:1332646, without installing the internal battery. To avoid damaging the original back battery cover, I...
thingiverse
I designed this to slip over the VR knob on my Radiolink RC6GS RC remote. I use this to steer the rear axle on my 4ws crawler. The gap in the pattern lets me feel where center is without looking at the remote. It's worked out really well for me. ...
pinshape
I own a RADIOLINK AT10 RC Radio that I'm eager to use without its internal battery, instead relying on my custom field battery design available at http://www.thingiverse.com/thing:1332646. To avoid compromising the original back battery cover, I'm...
thingiverse
Throttle gates for RC Transmitter, designed for Radiolink ATS9 however I think it will fit most radios as it looks like a common size. This plate serves as a guide when you only wish to have forward and aft stick movement. You twist off the thumb...
thingiverse
The original foam donut does not fit that tightly on the Radiolink radio and the wheel itself has a pretty small diameter in comparison with those from Futaba, Flysky, and Airtronics. This matches those much more closely while providing a better...
thingiverse
Slim case for the TS100 Soldering Iron Listing on Etsy: https://www.etsy.com/listing/875012067/ts100-soldering-iron-slim-case
thingiverse
I am another stand for the TS100. ... New Revision 16.05.2020.
cults3d
Remix of TS100 Frog Case without Xt60 connector https://www.thingiverse.com/thing:4352983
thingiverse
Store TS100 Soldering Iron, 4 spare soldering tips, stand, and adapters. ...
thingiverse
The TS100 soldering iron clips in to this holder. ...Can be screwed on to the table.
prusaprinters
Holder for Miniware TS100 soldering iron, spare tips and optionally small flux bottles.No supports required.
thingiverse
Place your valuable TS100 on any wall with ease using strong 3M double-sided adhesive tape.