radio stand 3d models

Stand upright with a handheld radio controlled unit attached to the rear, featuring an ultra-high frequency (UHF) signal transmission device.

I build this stand for my taranis which features a 5 mm wire handle, but it should work perfectly with many other radios as well; the result is truly outstanding. If you print this design, please do not hesitate to share your thoughts and pictures if...

This remix of FalconSrc's excellent radio stand is a breeze to print, sans support. ...To assemble it vertically, you'll need six M2.5 screws, on top of the standard components required by the original design.

This RC Radio Stand is designed specifically for pilots seeking a lightweight support that won't interfere with their back modules, similar to the popular TBS Crossfire system. ...It relies on just two M3 x 10 screws for secure installation.

This is a remix of a model by Mic on Printables. ... https://www.printables.com/model/400420-malahit-radio-stand The original model was created to fit the Malahit DSP1 radio. This model is scaled up to fit the Malahit DSP2 radio. ...

Very simple radio stand, perfect for most handheld radios including Baofeng, Kenwood, Yaesu, Icom, Anytone and many others. Just slide the clip over the top. v2 - Basic stand for smaller radios with standard antennas. v3 - I discovered that using a...

The X1M Pro HF radio stand can be bought in the US from http://www.wouxun.us/item.php?item_id=302. This design is my first attempt at creating a stand that fits well without any hardware and packs flat. However, Version 1 didn't progress beyond...

To prevent the radio and stand from sliding across the desk, I recommend attaching thin adhesive rubber feet underneath the stand. ...I built my stand using an Ender 3 printer with a 30% infill density and support structure featuring a one-layer-thick...

Stand for the Baofeng radios.

I'm standing near my mcHF Software Defined Radio.

A stand for my CB Radio

Stand for a YouKits HB-1B QRP radio.

stand for rc radio 60x120mm print with infil 20% PETG. ...take 2 strips 2,5mm and connect

Radio brand: Sihuadon, model: R-108. ... I think the same radio is sold under other brand names also. Useful stand that supports the radio when on a shelf. Modeled in Freecad .19, Sliced in Cura 4.13. ...Print time: 1:30

This stand is specifically crafted to hold your Mark Twain Radio securely, keeping it elevated and easily accessible in any room.

This stand is originally designed for the Hytera PD365, but it also fits the Baofeng UV-5R perfectly. It secures itself to the "feet" of the radio, preventing it from slipping out. Print Settings: Printer: Prusa i3 Rafts: None Supports: None Infill:...

This is a custom stand designed specifically for the Grecom PSR-800 and Whistler TRX-1 handheld radios. Currently, it's still a work in progress with plans to incorporate dovetail joints that will securely connect the two units together.

The stand can be used for other devices like HT radios. You will need to duplicate the number of parts needed for each project. Print Settings Printer Brand: LulzBot Printer: TAZ 5 Rafts: No Supports: No Resolution: Standard Infill: 20% Notes:...

The smaller stand is designed specifically for the matching Panadapter, but it can also be used for other devices such as handheld radios. To complete this project, you will need to duplicate the number of parts required. Print Settings: Printer...

The stand can be used for other devices like HT radios. You will need to duplicate the number of parts needed for each project.</p> <h3>Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>LulzBot</p> <p class="detail-setting...

Radio brand: Retekess Model: V115. ... Another skinny portable radio prone to tipping over. Modeled in Freecad .19. Sliced in Cura 4.13. ...Print time: 1:30

Designed for pocket radios with a width of 55 mm and a thickness of 20 mm, such as DEGEN DE333, KAITO KA200, TECSUN DE797, LOTTE Pinky7.. ...etc

I'm setting up a CB radio setup and I need a sturdy base to hold it in place, so I've chosen to use a human as a makeshift antenna support.

It's scripted in OpenScad and if the variables for length and depth are changed to your radio and you don't need to change the cutout it should scale fine. So far I've printed one for the Tecsun and another smaller radio branded Borne. The scad file...

This allows the connection wire from the radio to be kept off the ground, preventing any potential damage or interference. ...The holder is also engineered to fit seamlessly with most printer designs, providing a snug and secure fit without compromising...

Just a simple stand for a uSDX to make viewing the display easier. ...It uses two M3x8mm screws to attach the feet to the stand.

It's perfect for situations where you don't want the device to lie completely flat or stand up straight in its usual position. The angle of the upright pieces was carefully calculated after refining the initial design, allowing it to fold neatly...

A compact and practical base for the versatile Baofeng BF-UVB3+ handheld ham radio, created by repurposing Resago's ingenious tabletop radio stand specifically designed for smaller two-way radios.

After owning a metal radio stand for an old Futaba radio in the past, I decided to reverse engineer it and refit it to match my current radios' requirements. This design will accommodate radios with handles of 4 and 5 mm diameter, simply requiring a...

... needed. ...A DWG file has been shared in case you want to modify it according to your radio stand's specifications. ...To provide additional stability and protection, attach two L-shape legs to the bottom edge of your Horus X10 using double-sided tape.