racestar rc 3d models
29733 3d models found related to racestar rc.
grabcad
Model of Racestar motor BR4114, Low derail file of reference and educational purposes.
grabcad
A brushless motor is an electromechanical device that functions without brushes for the commutation process. It uses permanent magnets and a stator to create a rotating magnetic field, which drives the rotation of the motor's rotor. These motors are...
thingiverse
Proteus v2 rearfuselage with added motormount for RaceStar 2306S
thingiverse
I added motor mount for RaceStar 2306S motor and oval hole to rear fuselage for motor's electric cables. Diameter for motor mounting holes are 16mm and 19mm. Warning: this design has not flow yet so use it at your own risk. ... You can download other...
prusaprinters
With this motor mount you can install a Racestar 4108 in your Slingblade. Propeller 9x6 6S / 1300 mAH LiPo ESC 40 Amp Very hot ;-)) There are two versions of the part. One version is for the new building, the other version for retrofitting on...
prusaprinters
With this motor mount you can install a Racestar 4108 in your Slingblade. Propeller 9x6 6S / 1300 mAH LiPo ESC 40 Amp Very hot ;-)) There are two versions of the part. One version is for the new building, the other version for retrofitting on...
thingiverse
With this motor mount, you can install a Racestar 4108 in your Slingblade. The propeller size is 9x6 inches, and I recommend using a 6S / 1300 mAH LiPo battery with a 40 Amp ESC. It's going to be very hot, so make sure you're prepared. There are...
cults3d
17x4.5 and 16x16 Rims with Goodyear slicks and front runners. Brakes included: Strange drag rotors and calipers. Scaled to 1/25-1/24. May be rescaled as needed. Files are provided for personal use only and may not be redistributed. ... Selling of...
thingiverse
Motor Mount for Pattaya 3D Sail Plane: A Compact Solution The motor mount is a single, compact piece designed specifically for the Racestar2205 motor. However, it may also fit other motors of similar size. To secure the motor in place, I used the...
thingiverse
... was created using the Customizer at http://www.thingiverse.com/apps/customizer/run?thing_id=46605. ...To personalize it, set Max to 0, add initials (RC), leave Build as 0, and enable Over and Down with FONT size of 12.
thingiverse
The Electric Skateboard RaceStar 5065 Motor Pulley is also worth considering, especially with an 18t for a 15mm wide belt. I printed it in Nylon 100% infill at 50 miles per hour and it held up but I would recommend using something stronger in the...
thingiverse
For a twin engine setup, you'll need: * 2 - 5065 motors (I used Racestar 5065 200KV) * 2 - 8mm threaded rods, approximately 18cm long * 4 - 5mm threaded rods, approximately 25cm long * 8 - 8mm screws (self-locking nut or thread locker is advised) *...
thingiverse
Print it directly onto any desired filament. ...Visit Tomoquads.com.
thingiverse
Adopted impeller for 2205 motor shaft and nut. Made a box for motor, pipe connector, and changed base plate to match the motor box. ... This is remix from https://www.thingiverse.com/thing:4903481
grabcad
A RC hovercraft is all you need for an exciting flying experience.
thingiverse
Dies ist ein RC Frachtschiff mit einer länge von 43 Cm und einer Höhe von 13,8 CM es ist gut für den Einstieg gedacht/This is an RC cargo ship with a length of 43 cm and a height of 13,8 CM it's well designed to get you started