quinled dig quad 3d models

 More venting slots have also been added.The board used in this case can be found here: https://quinled.info/pre-assembled-quinled-dig-uno/ I used 4 x M2.5x5mm Pan Head screws to attach the Uno to the case. ... It is a tight fit, but does hold the board...

Just a case i threw together for dig-quad v2. It's a tight fit with plenty of air flow. ...Will not fit ethernet board

This mount is designed to fit 3 Dig-Uno Controller boards, this will allow higher density in your box.This PSU Mount is designed to fit the standard hole dimensions for Meanwell LRS 350, Generic PSU, and Meanwell LRS 600The design has a in-cut on the...

Just a case i threw together for dig-quad v2. It's a tight fit with plenty of air flow. ...Will not fit ethernet board</p> <h3>Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Creality</p> <p class="detail-setting printer"><strong>Printer:...

Remove ESP controller, place quinled quad inside the case and connect the signal cables

... (https://jboards.ecwid.com/) Power Distro-4 (2 spots to mount this one), Power Distro-8, or Diff-To-Port board to the power supply. ...I also made an adapter to mount Quinled's Dig-Quad (https://drzzs.com/shop/digquad/) to the power supply as well.

... (https://jboards.ecwid.com/) Power Distro-4 (2 spots to mount this one), Power Distro-8, or Diff-To-Port board to the power supply. ...I also made an adapter to mount Quinled's Dig-Quad (https://drzzs.com/shop/digquad/) to the power supply as well.

I've modified the files to make them compatible with each other and Quindor's QuinLED quad. There are two lid versions - vented and non-vented - but I haven't tested heat buildup yet, so I recommend using the vented one for now. I added a hole on the...

Mounts for...QuinLED Dig-QuadQuinLED Dig-Uno ....more info at: https://quinled.infoMean Well RSP-320-5 300W (60A) 5Volt Power SupplyThe Dig-Quad/Uno PCB fits over the pegs, then melt the pegs down with a flat soldering iron tip to secure.Optionally...

Quinled Dig Uno case with cherry mx button on top and a DC jack

QuinLED Dig-Quad QuinLED Dig-Uno ....more info at: https://quinled.info Mean Well RSP-320-5 300W (60A) 5Volt Power Supply The Dig-Quad/Uno PCB fits over the pegs, then melt the pegs down with a flat soldering iron tip to secure. Optionally...

"Left" side is spaced 41.808mm and the “Right” side is 32.322mm as per document https://quinled.info/quinled-dig-quad-board-dimensions/ (the v1 holes are 91.897mm long, that is the only difference between the 2)Relay holes are 20mm wide and 40mm...

A case for the Quinled Dig Uno by Intermit.Tech. Good project to DIY with digital adressable led's I use the board with WLED in combination with home assistant. Perfect combination. An update from https://www.thingiverse.com/thing:4006086 ...

Mounting Hardware: 4x - M4 - 8mm bolts (secure mount to PSU) 8x - M2 - 12mm bolts/nuts (secure controller to mount) Dig Octa System - https://quinled.info/quinled-dig-octa/ MW LRS 350 -...

I wanted a nice enclosure for my QuinLED Dig Uno board and quickly put this together. Still a work in progress but it should all work! Variety of ventilation covers included (and one with no vents so you can make your own).Features:Plenty of room for...

This box was specifically designed for an under cabinet lighting project using a Quinled Diguno, WLED, Home Assistant and a Lutron Caseta remote to control it.Please note that the hole in the case for the DC barrel connector is a bit too small and...

This box was specifically designed for an under cabinet lighting project using a Quinled Diguno, WLED, Home Assistant and a Lutron Caseta remote to control it. Please note that the hole in the case for the DC barrel connector is a bit too small...

I borrowed the design from the QuinLED dig-uno base. I also added support and two holes on the vertical sides for the external antenna version and holes for screw mounting if desired. I personal just use dual lock Velcro to mount this base. The...

... Dig-Quad. You can mount the Dig-Quad to the bottom and mount it then insert your wires and then add the top. I wanted something that was easy to rewire if needed. Additionally, I designed it with an opening to replace the fuses if needed. ...

Case for the Dig-Quad V3 (will not fit previous versions due to small PCB size change) Lids available for either wifi or ethernet versions Change Log 12-16-21 - Initial design 01-04-22 - Standard lid design for all Dig controller cases, extra support...

Case for the Dig-Quad v2 (will not fit v3 due to small PCB size change, version for v3 can be found here: https://www.thingiverse.com/thing:5166311) Lids available for either Wi-Fi or Ethernet versions

I adjusted a previous cover. ... While it fit great, I wanted to add text to the cover. Additionally, the cover snaps into place, leaving no need for screws. I removed the screw holes. Fits Dig-Quad Case...https://www.thingiverse.com/thing:4690991

Also moved the wire slots on the side faces so they lined up with my DIG-quad. Made the slot for the ESP32 antenna larger so that the ESP32 can be taken off and replaced easier. Moved vent slots so that they line up better with the heat sinks on...

QuinLED Dig-Uno Board x 2 (https://quinled.info/2020/02/11/quinled-dig-uno-pre-assembled-available/) 6. USB-C Cable (https://www.amazon.com/gp/product/B07SN9DJ5G) Wiring Supplies: 1. XT60 Splitter x 2...

Test Subject Enclosure System

<p>test enclosure</p> <h3>Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Creality</p> <p class="detail-setting printer"><strong>Printer: </strong> <div><p>Ender 3</p></div> <p><strong>Rafts:</strong></p> <p>No</p> <p...

<p>Simple to print, print face down.</p> <p>This PSU Mount is designed to fit the standard hole dimensions for PSU (verified on Alitove and Meanwell).</p> <p>The design has a in-cut on the bottom to allow for nuts/bolts to rest above the PSU. ...Design...

Simple to print, print face down. This PSU Mount is designed to fit the standard hole dimensions for PSU (verified on Alitove and Meanwell). The design has a in-cut on the bottom to allow for nuts/bolts to rest above the PSU. Design only uses top...

Simple to print, print face down. This PSU Mount is designed to fit the standard hole dimensions for PSU (verified on Alitove and Meanwell). The design has a in-cut on the bottom to allow for nuts/bolts to rest above the PSU. Design only uses...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/llI9BoYM0xk