quill 3d model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

As far as assembly is concerned, it's all pretty self-explanatory when you see the models, but here are a few tricks: Use as little wire as possible, but make sure you use good wire. The wires run from the grip and back, across the side of the...

This set may fit other models. I can't make guarantees on fitment.\nAnyone familiar with the Makerbot series printers will know that it's quite dark in the build space. They provide you with a roving white LED, and a red AMBIANCE LED which is both...

 V4 was still a solid design, but I made some very subtle changes based on my range outing last weekend where I was using it on a handgun.The Magnetospeed Sporter chronograph has some mounting limitations compared to the V3 model, so I wanted to...

When properly positioned, the latches are ready to engage by sliding the wiring cover all the way to the right.\r\n\r\n###Parts List:\r\nAll links at Amazon:\r\n\r\nQty 2 required: 8X2mm...

This allows the flow rate to be tweaked only for the detailed layers [as described here](https://support.ultimaker.com/hc/en-us/articles/360013370140-How-to-adjust-print-settings-of-a-part-of-my-model-in-Ultimaker-Cura). Update 4/10/2022 (v4.2):...

My original plan was to also model a strap clip for the bottom of the mount, but I found that it was unnecessary, as the entire thing can be attached directly to the head strap and head pad with a velcro strap. I used a couple of long velcro cable...

 I'm confident anyone here can just casually rotate the model right-side up in your slicer.This is licensed CC BY-SA 4.0.  Please feel free to republish this.  Feel free to remix this.  Feel free to use it for commercial purposes and make loads of...

Have fun and use common sense ;) This is my own creation and the model can also be found on Thingiverse thing:3771579 Print instructionsPrinting info: Printed on Prusa i3 MK3S, PLA 0.2mm layers, 4 perimeters for strength, main mount was printed...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

I downloaded and printed two of the Flugzeug Halter - Breit STLs in the Model Plane Ceiling Hooks thing from dschiedsch. They worked but were a tight fit for some planes when I tried them out. That is when I decided to make something adjustable to...

I could not find caps / hoders which suited my project, starting from inspiration of certain models existing in AA, I made a design under fusion 360 which corresponds in the size of integration, as well as the possibility of making spot welding. ...

Don't use it for rendering or model generation. (see Reducer picture) PRINTING NOTE Print at 100% infill. Try and print standing vertically, if possible so that scaffolding may be ommitted on the inside. These are for sink and drain plumbing only,...

High Power for Affordable Price We utilize "the fullest possible use of open source" combined with the buyer's self-assemble model to offer this superb laser cutter and engraver equipped with a high-power 40W CO2 laser tube and large cutting area at...

The source of the model has several parameters that you may wish to change. The current settings are for a silicone tube with an internal diameter of about 4 mm. You can adjust the pen length and width to your preference. Note that some tweaking may...

I haven't printed it yet, but the OpenSCAD model turned out pretty well. See the additional .scad file, .stl and the explanatory symbols image. The original bezel is dark grey with a textured interior except for the plinth and label obrounds. This...

The shade is 196mm high - be sure it fits your printer's build volume. Print it in white or even translucent PLA. The model has been adjusted in Meshmixer to be solid. You need to print this in <strong>Spiral Vase Mode</strong>! This will print the...

...The design is optimized for the given print orientation - no need to rotate the STL model.You will also need two of the strain relief clips, which I have provided as a separate project.Assembly6 pieces of M3 nuts have to be pressed into the plastic.

The extra space available in a Volcano setup would allow much more open channels and sweeping paths, and I would like to improve the Volcano version in future, but this will require significant modelling work which I just don't have time for at the...

I can only describe what I did or share my experiences and provide respective models and a SketchUp project concept file (the .skp file) so that you can adapt or improve it for your Stargate. In one of the comments from '5ft Lighted Stargate'...

I first encountered the idea for this type of robot in a biomedical article, presented as a potential new candidate for exploring the human colon due to its simplicity and ability to navigate confined areas....

The color thicknesses and the width of the outline stripes on this test print match the stripes on this case and future cases I upload will probably use similar...

I haven't printed it yet, but the OpenSCAD model turned out pretty well. See the additional .scad file, .stl, and the explanatory symbols image. The original bezel is dark grey with a textured interior except for the plinth and label obrounds. This...

I modeled this in Fusion 360, and you can find the source files as well as IGES included. I printed it in PETG since that's what was in the printer. The infill was 30% with three solid layers. ... Print Settings: Printer Brand: MakerGear Printer: M2...

Then, once the mount is installed on the handle, you can unscrew the bolt and increase the distance from the magnit to the sensor, increasing it enough so that the brake sensor only activates when the brake is actually applied.The model is made in...

&nbsp;The SFX version backplate does not fit the build plate of a Prusa Mk3, so this project is temporarily on the pre-prototyping stage.For the FlexATX version, click this link.&nbsp;The enclosed design includes two types of motherboard trays of...

http://www.thingiverse.com/apps/customizer/run?thing_id=53235 Instructions Using the following options: crankSlack = 1.8 times smaller gear_tolerance = a negligible 0.1 inch midAxisHolderH = stands at an impressive height of 6.3 inches noteAlpha =...

This model fits seat shafts with a 16-groove, skip-tooth-top, 12mm nominal shaft:&nbsp;(note skipped groove, blue arrow)&nbsp;Probably best to print these with the spud pointed up for minimizing how much trouble the overhangs inside the hole will...

It has been almost three months in the making, and several bits are an additional 100–200 sketches beyond the base model, which means there is a ton of Mf-detail, I probably overdid it. My goal was to create something special for kitbashing,...