quiet fans for ender 3 3d models

I designed this Fan Duct for any stock Creality CR10 or Ender3 (including clones) setup, which is inspired by my Fan Duct for the MicroSwiss DirectDrive (https://www.thingiverse.com/thing:4886226) to increase the part cooling capabilities. . . It...

New Covers, if you want to make both 40mm fans to do a push

16/02/2022 Major Update: Titanator Version 2 Changes: Reduced the number of parts Significantly increased structural rigidity The bed leveling sensor has been completely redesigned Added support for Volcano hotend Fixed the gaps between the air duct...

Yet I bought it for home use and struggled to make it quiet enough. Normally you'll have to disassemble all battery bank to replace fans. This project completely replaces front panel with a new one, which allows you to install any 80mm fans you want...

... necessary to print the first duct... Please, I would love if you can test in your printer and share the results with me :) PS: I decided to mount the fan outside of fan housing to be easier to make some tests with buffer materials as foam... ...

Hardware Info: https://www.thingiverse.com/thing:5368944 (Optional: 4x M2x10 4x M2 Washers for 4010 Blowers) CR Touch Probe Offset (Roughly): https://www.thingiverse.com/thing:5273623 Enjoy! P.S. ...I also added a non-Brass Insert version of the CR...

Upgraded cooling ducts to get a better print quality on the Ender 5 S1.

... and green levers, along with an orange pawl and green rocker. The green rocker oscillates, featuring two red stoppers mounted on it for added control. ...The mechanism operates silently as the rocker returns, preventing pawl-to-wheel contact.

You will need: 4 x M5 bolts (you should have at least 2 from Ender) 3 x M3x20 bolts for the lid 8 x M3x20 bolts for the fans 4 x M3x10 bolts for the SKR board 4-12 x M3 nuts for board height adjustment 1 x 12/24v to 5v step-down module 2 x 4010 fan...

SKR 1.3 Ender-3 Case | One side drawer | 2 fansI wanted smallest possible case and I am not using Raspi so these double drawer designs were overkill.You will need:4 x M5 bolts (you should have at least 2 from Ender)3 x M3x20 bolts for the lid8 x...

Offsets are defined as follows: STOCK fans holder for bltouch #define X_PROBE_OFFSET_FROM_EXTRUDER -44 // X offset: -left +right [of the nozzle] #define Y_PROBE_OFFSET_FROM_EXTRUDER -14 // Y offset: -front +behind [the nozzle] HeroMe #define...

Shroud for ender 3 fan, it have a test print for core only to make sure it fits snug, in the fan hole.

Gpu holder for front mounted be quiet pure wings fan

Lid for mainboard case on Ender 3 upgraded with second fan. ... Honeycomb covers for fans are there: https://www.thingiverse.com/thing:3280998

**A few more versions of Lil Boxie for Ender 3.** One for a Microswiss hotend, and one for a copper T-shaped hotend. These are All 4010 fans. Probe offsets: -44.13, -6.78 **Update** 2-22-22 Added Boxie PinPoint E3 40MMF MK1.stl and ...

This is a modified version of the Base stand to attach 3 Fans on one Stand. You probably have to Slice it. modified for 120mm fans. ...i didn't test it on 140mm fans

Simple Louvre Style Intake Fan Cover for Ender 3 Use existing screws to attach. ...Link to other Ender 3 mods - https://www.thingiverse.com/thing:3286521, https://www.thingiverse.com/thing:3369736, https://www.thingiverse.com/thing:3213429,...

Ender 3 Max stock fan mount for micro swiss ender 3 use the nuts that came with micro swiss to hold fan side on left right does not need and use one for bl touch Made new firmware with correct level point link soon Bl touch attaches to micro swiss to...

:-) This mod is verified to be compatible with: - Ender 3 S1 - Ender 3 S1 Pro - Ender 3 S1 Plus As of version 4.0, this duct is compatible with: - Spider Hot End Mod (3.5mm lower, use the provided STL, not the stock one) This mod is NOT (yet)...

Lightweight Build for Single 50x50x15 or 50x50x20 Fan More Than Enough Cooling is Provided A Previous 80x80x15 Version was Used, but it Provided Stupidly High Amounts of Airflow :D The Downgrade to a 50x50x15 Fan Has Been Made Images are Available at...

There's also screw posts for a second buck converter, for if you want to switch to dual 12v fans (like noctua ones) for part cooling. I wouldn't use a 12v noctua for the hotend cooler due to a lack of cooling potential to avoid heat creep. The .f3d...

... plate has been generously enlarged for optimal airflow and reduced noise levels. This design modification significantly minimizes the fan's noise output, while also allowing for adaptability in various applications if the hole pattern is compatible.

This is a cover for the Ender 3 from 100 to 105 mm hole axis.

Thanks to eric-anastas for this magnificent design and for sharing the step file i had remixed it to add another filament Colling fan, i am not an expert in the air flow but i thought that by adding another fan this will make sure an enough air flow...

Remix of: https://www.thingiverse.com/thing:3419531 - Designed for my Ender 3. - Mounting on the retaining plate instead of on the hot end. - Holder for BL Touch. - You use the screws to cut the threads in the plastic, thus no more nuts needed. -...

Thanks to eric-anastas for this magnificent design and for sharing the step file i had remixed it to add another filament Colling fan, i am not an expert in the air flow but i thought that by adding another fan this will make sure an enough air flow...

###*2020-10-31 Update* - Better BLTouch placement ###*2020-10-25 Update* - Now in two parts to print easily - Two M3x6 bolts and nuts to join them - Optionnal BLTouch mount - Added clearance for X axis ###Features : - Dual 80mm fan mount - Fits...

Fan duct to greatly improve the air flow for print cooling without making major modifications to the machine. ... is mounted on the original fan.

... fans and direct extruder. ...If you want to use direct extruder it might be the best to use my mount https://cults3d.com/en/3d-model/various/ender-3-v2-direct-extrusion-mount-for-dual-gear Easy install with 1 screw. ...You might also need 2 doodly eyes

This remix combines the Ender 3 Flexion Extruder with an E3D v6 Hotend mount, as originally designed by Bratan. A right side fan duct and BLTouch Sensor Mount have been added for improved performance. The BLTouch Mount is thoughtfully designed,...