quiet fans for ender 3 3d models

Another ingenious solution for holding cables on the Ender 3 printer, a straightforward and uncomplicated design that gets the job done.

I designed a stand for Ender 3 spool holder. Print upside down. UPDATE: No need more resize the model to 1000%. ...Its already in real size.

This is my watercooled hotend as seen on Reddit https://www.reddit.com/r/ender3/comments/snmqwh/i_build_my_own_watercooled_hotend_for_my_ender_3/

I designed a stand for Ender 3 spool holder. Print upside down. UPDATE: No need more resize the model to 1000%. ...Its already in real size.

Ender 3 Camera Mount for use with a webcam with a tripod mount. ...Should fit a standard 1/4" bolt (same size as tripod threads)

I designed this enclosure specifically for my Ender 3 box to seal off the gap where all the cables pass through. ...It was printed using Filaflex.

My BL Touch cable was too high and the normal Ender 3 Cover pushed it down too much, it didnt work after it was closed. So i made this. ...if you want to install the fan you have to drill holes.

This is my attempt of ender 3 direct drive with clone BMG (Fysetc) and clone V6.I accidentally bought V6 without fan so i decided to make this with original fans.Its second iteration of this project and changes are based on flaws that i found in the...

The objective was to get the lightest and simplest set, using: - 4010 fan to the heatbreak - dual 4010 blower fans for filament cooling - BLTouch support - Extruder Stepper motor support (works with stock Ender 3[v2] or pancake) Print Tips...

... 3, and this one was a bit too short, so I modified it using meshmixer. ...This modification has been working perfectly on my Ender 3 for about two months now! ...Printing at approximately forty percent infill with PET-G at a layer height of point two.

Original Electronic Workhorse Ender 3 Pro / Ender 3, Dual 40x40 Powerhouse Fan Upgrade

A simply spool holder Ø200 width 60mm for Ender 3. Needs: 4 screw M3 x 12mm 4 bearings 608 AU4G or stainless steal plate, thickness: 2mm following the drawing added. ... Support simple de bobine Ø200 largeur 60mm pour Ender 3 Fourniture: 4 vis M3x12mm...

Filament guide for 3D-printer Creality Ender 3 or Ender 3 Pro on the top beam. This is required when printing from a filament dryer. ...You need 2 pieces of M3x40 screws and 2 pieces of M3 nuts (a rubber lock nut is recommended).

Very simple tray for Creality Ender 3 Max, that fits with the embed tools (19,5 x 10 x 5 cm). ... Très simple bac pour la Creality Ender 3 Max, qui peut contenir les outils livrés avec (19,5 x 10 x 5 cm)

Designed up this led holder for Ender 3 because I needed more illumination on the extrusion site. It fits perfectly on the back of the "extruder bar". It needs only a screw (existing) to lock it up. The led strip will be inclined by 45°. It...

This is a modification and remix of a "Fang" style fan mount for the Ender 3. The original link below was a fang desinged for the Tevo Tornado v1. I added supports for the original mounting hole locations used on the stock shroud. I also provided...

This is a custom modification and upgrade of a "Fang" style fan mount for the Ender 3. The original design was created by gdramos for the Tevo Tornado v1, as seen in the link below. I added supports for the stock mounting hole locations used on the...

I'd like to extend special thanks to Coillote and his Ender 3 design, which served as inspiration for my own creation. You can find his design here: https://www.thingiverse.com/thing:3044639 In the near future, I'll be adding a PSU cover to enhance...

For now I use original Ender's 3 24V fans with extra resistors to reduce the speed and noise. Most likely will replace them with Noctua or something similar in the future. The right fan is blowing in, the left one out. The airflow is just great. ...The...

CR-10 / Ender Hotend Cover For Stock Fans With Modified Upper Fan Input and BL-Touch

USB Holder design for Ender 3 v2, but can also be used for Ender3 and Ender 3Pro. It screws on down-left corner of the printer. ...If you have problems while you downloading files with ERROR 404, go to "thing files" right below and and click on...

**Elevate Your Ender Experience with a Custom Spool Holder** Upgrade your Ender 3 or Pro with a precision-crafted spool holder, designed to enhance your printing experience. **Gather Essential Components** To assemble this innovative accessory,...

I was tired of knocking my laser head off on my ender 3 so here is a mount that works with a go pro tightener. This can be changed out for any bolt of your choice. ...Happy printing/lasering

I was tired of knocking my laser head off on my ender 3 so here is a mount that works with a go pro tightener. This can be changed out for any bolt of your choice. ...Happy printing/lasering

I printed a cover for my ender 3 and it just slid off when it was printing and so then i desined this it hooks on the back of the screen so it doesn't just slide off

I was tired of knocking my laser head off on my ender 3 so here is a mount that works with a go pro tightener. This can be changed out for any bolt of your choice. ...Happy printing/lasering

A basic toolkit for the Ender 3 3D printer is all that's required to get started and unlock its full potential, allowing users to print a wide range of objects with precision and control.

A Customizable USB Holder for Your Ender 3 3D Printer, Designed to Accommodate Two Standard USB Ports and Three Mini SD Cards, Enhancing Your Printing Experience with Easy Access to Memory and Power.

USB Holder for Ender 3 I've frequently misplaced the USB, prompting me to search for a suitable holder that fits my Ender 3. Unfortunately, none of them met my requirements, so I designed this. Files Three files are included: - A standard STL file...

... is a remix of https://www.thingiverse.com/thing:3003725. Duct blower is a remix of Prusa hotend. Print all parts, use 2x M3 brass insert for blower fix and 2x M3x7mm screws For the rest recycle all Ender 3 screws of stock Hotend and related parts.