quick release nut 3d models

I have added "slide on" holders on my son's stroller to facilitate sliding things on and off, so I remixed the design of the slide on bracket + the design of the gimbal cup holder (from...

It can be quickly printed, assembled, disassembled, and relocated as needed. Four screws are commonly used, not for securing the fastener, but rather to enhance its structural integrity. The two M3*8mm and two M3*18mm screws serve this purpose...

This is a support system made up of two pieces designed to connect and disconnect quickly without any tools whatsoever. It's a bayonet-style anchor, the male piece gets inserted into the female piece, turns 1/4 turn, and they're connected. To...

Place to buy affordable cam lever clamp https://www.aliexpress.com/w/wholesale-bike-clamp.html?spm=2114.search0104.0.0.bOOZXW&initiative_id=SB_20170706105443&site=glo&groupsort=1&SortType=price_asc&g=y&SearchText=bike+clamp Requires one 9mm outer...

At first, I heated up a hex nut into the base to attach it to the tripod. Was a little too loose, so I spent a little time in Tinkercad and designed a different base for the same Wyze shaped top. ...Works great with this tripod I got from Amazon five...

This design allows you to quickly mount the fan holder from this link: http://www.thingiverse.com/thing:548305. However, you don't need to use long screws. You can easily improve this design, so feel free to modify it. It's a simple way to install...

Perfect for capturing stunning footage during high-speed chases or cinematic shots, this mount allows you to quickly switch the camera's position without needing any tools. Before installation, simply print multiple mounts and install them on your...

They cost about $10 for 8 of them and these are the ones I ordered, but you can get them from anyone: https://www.amazon.com/gp/product/B07L48XL2R/ It uses a 10-32 nut and bolt from home depot to secure the clamp and also a 1.5" diameter washer to...

They cost about $10 for 8 of them and these are the ones I ordered, but you can get them from anyone: https://www.amazon.com/gp/product/B07L48XL2R/ It uses a 10-32 nut and bolt from home depot to secure the clamp and also a 1.5" diameter washer to...

### Files * The following files are included: * `20_tooth_MXL_Motor_pulley.stl` * `USE_Hex_Bolt_Main_Body.stl` * `USE_Pins.stl` * `USE_Push_Plate_no_nut_needed.stl` * `USE_Thiner_Main_Belt_Drive.stl` ### Caution * The 20-tooth belt pinion is...

Use Part1 from the original and then use Part2b from here and a M3x10mm countersunk bolt and a M3 nut to fit the smaller plunger to the clamp. Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: Doesn't Matter Supports: No...

The ultimate goal is to be able to remove these M3 bolts, which would release the silencer from the flash hider. These M3 bolts would be threaded into a pull piece with some degree of freedom in the suppressor's rear end. Please note that this...

The tabs attach to grooves in the x carriage, providing a quick 3-second extruder removal by twisting and lifting. No additional hardware is required, and with proper printing, it holds as well as a stock carriage. Photos show an extruder without a...

... while zip ties are pre-positioned and tightened before curing. The upper carriage follows GregFrost's standard fixations, with quick connectors added to the extruder for easy replacement of the entire upper plate-extruder block in under a minute.

It's also crucial for me to be able to quickly, easily, and one-handedly detach the radio from my belt and switch channels at will. I've been dreaming about something like this for over 10 years now that I've been using this radio for work, and...

I designed this model to give me a quick and easy way to disengage the security bar on my sliding door. The previous solution used a fiddly little bar that slid into a slot to stop the bar from going up. It was a two-handed operation to open the...

Hardware a 95lb Magswitch 6 x M8x16 sockethead bolts 4 x M8x16 bevelhead bolts 10 x M8 T-nuts One fabricated piece of 1.25" x 1/4" thick piece of steel with two 8mm holes that match the holes in the Steel Plate holder and is beveled until the bevel...

A single bolt approximately 25mm in length and a complementary nut (recommended for added security) form the pivot point. To provide efficient clamping force, a compression spring measuring 3/8" x 3/4" or similar dimensions is strategically...

This replacement component swaps out the top piece of the extruder mount, two long M3 bolts & nuts, and one piece of rubber tubing. No longer do I have to remove the bolts to switch out filament. To achieve this upgrade, I employed two 5/32 inch...

for this model you will need the following: - 1 M6 screw - 1 M6 nut - 1 hair strap band The main idea behind this design is to use a hair strap band to pull a jaw whit the phone between it, if we want more pressure we will need to change the...

A single bolt, about 25mm long and nut (locking highly recommended) are used to create the pivot point. A compression spring (3/8" x 3/4" or similar) is used to provide clamping force. Tool can be pushed in to store and pulled out and away to remove...

This little hobby vise adjusts to any position quickly by lifting the screw up out of the half-nut and sliding the jaw into position. Lower the screw back down into the nut and tighten as with a regular vise. The secret, shown in the last photo, is...

Made a simple nut and bolt. It is a 1/2"-13 thread. Has a 0.17mm tolerance added to the threads so it should print fine on most FDM and still thread together. Prints perfect on my E3 Pro and screws together with ease right after printing. Usually...

Made a simple nut and bolt. It is a 1/2"-13 thread. Has a 0.17mm tolerance added to the threads so it should print fine on most FDM and still thread together. Prints perfect on my E3 Pro and screws together with ease right after printing. Usually...

Quick-release plate for my gopro to Velcro M47 tripod. ... You need M5 nut

Scale it up to 1000% by increasing the size of all dimensions exponentially, resulting in a massive spring that measures 18000mm in diameter and 200000mm in length. To achieve this monumental scale, start with a spring that has a staggering 90mm...

I made a mistake and lost the plate that holds my camera tripod's screw, so I created another one to replace it. Having multiple plates for each camera is always a good idea, even if you don't lose the original. I used screws from...

The [original](https://www.thingiverse.com/thing:1347792) printed in blue was a tad too large, the corners needed shaving to fit my tripod. Since I needed another one, I remixed, making one direction 0.6mm shorter and added a 6mm thread to make...