quick acting hold down clamp 3d models

The CH2 2P Quick Connector Spring Clamp Terminal Block is a versatile and convenient connector, perfect for various applications. It features a spring clamp design that ensures secure and easy connections. ...You can purchase this product from Amazon at...

Made for holding down project to CNC table. Cheap to print and replace. Two different sizes to accommodate different materials. ...Both have ¼ inch slots.</p>

Holding down paper

I took the SCAD file from @georgeprout and modified the dimensions to fit my 18" Irwin Quick-Grip clamp. ... These are the settings: // Overall dimensions w=40; l=49.4; h=11.3; // wall thickness and tab size wall = 3.7; tabl = 13; tabw = 5.4...

This design is tailored specifically for the Irwin 150mm Quick Grip Clamp. However, its compatibility with different sizes is uncertain. The estimated printing time comes out to be approximately eight hours. Supports are necessary for this...

I recently made some corner hold-downs for my cheap Chinese CNC machine, for working with small sheets of material and where I might want it lifted off the bed a few millimetres. To go with them I decided to make some edge hold-downs too, which I've...

I recently built some edge hold-downs to complement my low-cost Chinese CNC machine, perfect for working with small sheets of material and situations where I need it lifted just a few millimeters off the bed. To go along with them, I decided to...

I broke one of the end clamps of the quick clamps I use, so I decided to try a re-design it given that I had the piece parts with me. I think it turned out really good! I have not yet printed it, I will update as soon as I do it! Hope you like it! I...

Inspired by the "Centering F-Clamp Cap for Pipes" from @NextStep I created this design to fit on my bigger quick F-Clamps (rail width 24mm, length 40mm, thickness 5mm). Print Settings Printer Brand: Anet Printer: A8Rafts: No Supports: ...

The "Anvil" is also optional, for where you've got a solid face on one side of the bar and don't want or need to clamp it specifically; the Anvil replaces the Clamp Mount (and Cam Lock) and just clips on and allows you to apply force through the...

I installed an Ultrabase on my Anycubic Kossel printer, but constantly had to relevel the bed because the hold-downs were unable to keep the base firmly in place. To address this issue, I designed custom brackets using Fusion 360 specifically for my...

All three use the same Neodymium magnet from Amazon: https://www.amazon.com/dp/B01MSTKTSF/ref=cm_sw_em_r_mt_dp_kBw7Fb2RM2QZS?_encoding=UTF8&psc=1 Note: I find these are too large to work well on the edges of the honeycomb, so I designed my own...

The Quick Clamp Lampshade Upgrade for Lunartec / Luxartec Swan-Neck 1 W LED Lamp is designed to enhance the functionality and aesthetic appeal of this sleek lighting fixture. When the lamp is in its default setting, it produces a highly concentrated...

it uses an Irwin QUICK-GRIP Bar clamp with a 13mm x 5mm bar, to attach your GoPro on a shelf or table or just about anywhere.&nbsp;This consists of 3 parts, no support should really be needed, but you may find some tiny supports on the recesses for...

Compact Case for High-Power USBC DC-DC Buck Converter Charging Step Down Circuit Module Fast Quick Charger from AliExpress

... Does not need supports, uses 45 degree angles, prints in 9 minutes on a Bambu Lab X1. I added a little notch to hold the end of the spring so it doesn't fall out so easily and simplifies installation.

The back of the yoke can lift slightly if it's pulled excessively but in normal usage it's secure enough.&nbsp;It's completely designed around a 34mm thick desk (ikea) so it might be a bit specialised, maybe the 'yoke_table_clamp' part could be...

This is an upscaled and modified version of a quick release clamp (Similar to those on bicycle saddles). I designed it for our sand box roof, because the screws were pretty unhandy. You have to use M6 screws (length depends on your sand box model)...

You will need 9 4mm x 20 cap screws and 3 4mm lock nuts. ...I printed the clamp in pc and the cam and washers in petg.

I designed them for the really good one-handed clamps from Amazonbasics, but they should fit just about any one-handed clamps. All adapters are printable without support if printed in the position I have posted them here. To use the adapter with...

this is part of a clamp. I have tried to use as much detail as possible in the workpiece. I had a problem and made my own design. ...If you like the model and would be kind enough to support me monitarily for my work, consider supporting...

I'm showcasing a unique clamp component that I designed from scratch after encountering an issue with existing designs. The level of detail in the model is considerable, reflecting my dedication to precision and quality. ...If you appreciate this work...

Camera equipment. ... A budget priced quick release set. At $35 shipped, cant go wrong on this part! * You are welcome to use this model for personal projects, renderings, learning, and so on. ...Please do not resell or redistribute this model.

Crimson-Tipped, Double Pole (2P) Spring-Loaded Quick Connect Terminal Block - Amazon's Choice for Electricians and DIY Enthusiasts. Securely Attach Wires with Ease Using This Essential Electrical Component. ...Order Now at Amazon.com.

A replacement jaw for automatic F clamp. 18×5mm rail, M6 hardware. I have printed V1 (on the image) but later I've increased tolerances and removed the elongated section (that supposed to be on the other side), but I didn't print the V2. I printed...

A replacement jaw for automatic F clamp. 18×5mm rail, M6 hardware. I have printed V1 (on the image) but later I've increased tolerances and removed the elongated section (that supposed to be on the other side), but I didn't print the V2. I printed...

The bracket remains securely attached to the wheelchair when the student leaves, then quickly reconnects the switch for an augmentative communication device the next morning. I used 2" x 1/4" bolts and 1/4" nuts inside the wingnuts. To pause the...

for those who like to mess around with the extruder, i got sick of removing the screws so i made a quick release, you will need a m3 x 25mm screw for the hinge. I used PETG, print with supports on the hinge space and make the arm solid. ... <a...

I made this model for my Galaxy S8 in it's case, so check the dimensions of your phone compared to the ones shown in the photos provided for this part and adjust accordingly, if needed.I'm not sure if there is a standard for the quick release or not,...