quest 2 paddle 3d models

Print face down with supports. Will need M3 x12mm bolt and nut. ... Will update more info soon.

Cable clip for your Oculus Link cable, just snaps onto the side of your headset. This helps relieve stress of the very strained and weak USB C connector on your headset. Best printed in ABS or PETG but can be printed in PLA and will probably work...

Designed this Cable clip to use with any cable up to 7mm thick. ...any cable smaller will fit but be a bit loose Printing: orientation: Make sure the print is on it's side this way it prints best and cleanest infill: best result use 100% but...

A modification of the great [oculus wall mount](https://www.thingiverse.com/thing:4630669) by lensfort by adding two little hooks to hand the controllers from

Decided that even if I can't see it most of the time I wanted a cool sci-fi gun instead of the realistic Glock 17 of Cheweey's Chewey_GLK-17 so I adapted the muzzle from FurtherFabrication's <a...

Printed without supports 30% infill is probably overkill printed at 100% scale it is fairly loose on the mount (cable tie added some resistance) can be used also just to add some weight to the back of the headset i wasn't sure how much...

This is a remix of another users model that wasn't wide enough. ...I went ahead and rescaled the model and added a spot to insert the grips of the controllers., the grips do fit rather snug and the wrist cords need to be over the top when inserting.

My clip broke when I threw the disk too hard in Echo VR, I designed this so it can connect without a new strap. It is a bit hard to put on and it is snug at the beginning, after some time it will lossen up and be even better than the original. ... ...

The idea is not to glue your magnets diretly to each other cause they would easily break the glue and tear each other from their spots. ...The lower magnet is being placed and glued from lower side so that it can't be torn apart during usage.

Come si vede dai file, si tratta di un remix degli oggetti sopracitati ( https://www.thingiverse.com/thing:4629343 e https://www.thingiverse.com/thing:4629958), uniti e opportunamente migliorati per evitare una stampa di 4 ore per pezzo, ma con la...

Original model by Kookala.I took a bit off the bottom for easier installation. ...Worked a charm in my left controller.

This adapter is slide-in assembly. The main purpose of using the sliding-in installation design is to reduce possible damage to the main body of the VIVE DAS during installation. please refer to the animation for details.

I was going to do a similar design but I found that ThePandaFly beat me to it. The hole for the lanyard was a little too small in his design and it was a little hard to get in on to the ring so I did some minor adjustment. The menu and Oculus button...

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

Remix of the Oculus Knuckle straps lock. I couldn't get the locks to work well in the original model. No matter what material I used they would snap too easily on that narrow neck that extends from the handle. I decided to try to make locks...

Remixed from https://www.thingiverse.com/thing:4629958 This clips on to the loop on the back of the elastic headstrap.

I was drawn to the short "stem" in the original design and the sturdiness of the design I remixed. By combining the two, I've created a new design that has yet to break. If you have access to TPU, I would recommend printing this design with it,...

5 walls, 0.1mm, x2 infill lines, triangles, 20% infill Cut Oculus Strap as close to the old clip as possible. Melt the cut end until there is one solid line of plastic on the end on the strap, for strength reasons. Print the new clips and use...

Second generation virtual reality headset for oculus and its controllers. ...(left and right)

A bit remixed version from https://www.thingiverse.com/thing:4632370 which is a remix itself already. I applied cable placement from my other cable clip to facilitate the cable from aliexpress to elite strap. ... Cable thickness is about 6mm and this is...

A new head strap design that only requires some screws (no bearings or anything special like that). You will need 11 m3 screws about 10 mm long and a bit of glue (you can also do it with 3 screw and a bit more glue). Just follow the picture and...

I didn't like the sanlaki's own controller mounts since they were kind of low poly and hard to work with. So I cleaned the stl model and made it smooth. I printed both of the versions, the low poly version and the smooth version both came out really...

The 3D model was created on real base. ...It’s created accurately, in real units of measurement, qualitatively and maximally close to the original.

a full q2 elite strap replacement remixed from the original model by niuva https://www.thingiverse.com/thing:4791811 i'd recommend printing out of petg printed on an ender 3 max

An user on reddit requested this and I decided to make a version. ... The file is for the right hand, just mirror a copy for the left hand

<p>Headband for DAS Mod, includes a a buckle you have to glue on top so you can slide the end of your DAS nicely under it. ...Print with support everywhere.</p><p>Remixed from: <a...

I wanted to use the head strap of Quest3 with Quest2, so I made it.Please be sure to read the notes below and use at your own risk.When attaching and detaching parts, there is a possibility of damaging the VR device itself.Depending on the strength...

Remixed handler for bobo-vr strap back part. Many thanks to author of original stand, it's very good designed. ...

<p>Dies ist ein Remix von "Mike vom Mars" <a href="https://www.thingiverse.com/thing:4025967">https://www.thingiverse.com/thing:4025967</a></p><p>zu dem Brillenträger und Ständer gibt es noch eine zusätzlichen Träger zum aufsetzen, der das Elite...