quest 2 nose gap 3d models

My final version of an elite strap alternative: Advanced Strap I tried to imitate the elite strap as closely as possible. i think the plastic alone is very convenient, but i added an optional padding! Simply print it with some flexible material...

This is a remix of https://www.thingiverse.com/thing:4130801 and https://www.thingiverse.com/thing:4623302. ...The design is still a work in progress as the fitment isn't quite right but I'm not sure if that's because of my printer.

<p>Recommended printing face down with supports for the strap retainer area. ...I used 0.3 layer heights with a 10% cubic infill and it works great, but tweak to your liking.&nbsp;</p>

So this is a modification of https://www.thingiverse.com/thing:5355995 for use with slightly different washers with a hole diameter of 8.4 mm. These from the swedish shop Biltema works well.

Have been looking for a charger brick and cable holding solution, and the packaging box just isn't cutting it? Here's your solution! Simply print, place, and secure! - Print: Follow printing settings below (Place flat bottom along build plate!) ...

I modified the source stl to remove the remote holders. I used these remote holders instead. ... https://www.thingiverse.com/thing:4625235

A remix of Crispy3DPrint's Design but with no room for the headset as I have found you can just sit it next to the dock. ... Crispy3D's Design: https://www.thingiverse.com/thing:4724688

저는 VIVE 순정 스트랩을 퀘스트 2에 사용하려고 DAS 어댑터를 리믹스 했습니다

This is for https://www.thingiverse.com/thing:4788056/comments#comment-5701349 for printers that can't print the larger design. ...Took off the wings and made it super basic.

The fit is amazing it has holes for straps to fit through if you have them to hold the mount to the strap and the battery to the mount I have a rather rare battery, I doubt it will fit many peoples, but if you can modify it in tinkercad in the...

Made this to make the cooling system less restrictive on the main cooling system, it does require cutting into the front face plate.

Printing with the face down, made removing the supports a lot easier and prevented the tabs from breaking. ... (Please note, the cover used in the image has not been sanded/painted)

Just a bit narrower remix for smaller beds

For a long time I was looking for some nice lightsaber with which to play a good beat saber. so I decided to make it myself :) The lightsaber is fully printed consisting of two parts. ... unprintable part: the non-printable part is a threaded rod...

Remix by the IPD adjustment by tancach. I made the sleeve slightly bigger and without the groove so it fits over the lens and doesn't protrude. I also added all the sizes all the way from 59 to 67. The sizes are based on the previous model by tancach...

A remix of https://www.thingiverse.com/thing:4724688 splitting it for smaller printers. I split the model with a half lap joint to make it stronger and allow a good surface area to glue it. ...The O in the design was removed to allow for a thicker...

Works with almost any battery

<p>Improve your aim and enhance your experience by having the stock feel against your shoulder. ...Designed with Population One in mind but it should work well with other FPS games like Onward, Contractors, and Pavlov.</p>

Filament : PLA Layer height : 0.2mm Infill : 30%~40%

This is a remix from https://www.thingiverse.com/thing:398515 I used the snap fit file printed great on Ender 3 v2 and added the venom eyes on it. ...I used .3 resolution to cut printing time but at a .16 will look much better.

A remix of the lens protector to add the lens holder for my prescription lenses. The ones already available did not fit my lens size/shape so I had to design my own. Posting here in case anyone else might have similar lens types. ... Only the stl for...

<p>Made this to make the cooling system less restrictive on the main cooling system, it does require cutting into the front face plate.</p> <h3>Print Settings</h3> <p><strong>Printer:</strong></p> <p>Creality ld-002h</p> <p class="detail-setting...

Messed with meshmixer For the original https://www.thingiverse.com/thing:5337461/comments

You will need to solder the ground cable and one of the channels to each headphone (on my cable right was red and left was white and the ground was around those two) IMPORTANT: while soldering make sure that you press on the pins of the headphone,...

I used rafts because it is a small part. They snapped off easy enough. I made them to use better wrist lanyards. ... The straps I used https://www.amazon.com/gp/product/B07WJH8M87/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&th=1

For true adventure lovers like Bandit,LOL! 19 cm Heigth and 29 pieces. ...No Have Collors!

The 3D model was created on real base. ...It’s created accurately, in real units of measurement, qualitatively and maximally close to the original.

Cups for a stock