quest 2 golf club attachment 3d models

This extension allows to attach your Quest 2 controllers to a real golf shaft. Get you hands on some old putter or other club and cut the shaft in half. Now you can fasten the printed part to the shaft with 2 nuts and bolts. Alternatively you could...

I cut 30mm from the rubber handle on the club and attached in to the printed part, that should leave 3-4mm between rubber handle and the printed part. Drilling holes in each side of the gold club tube for the bolt was not easy. I had a hard time,...

... belt strap to secure your controller. ...You can get them here: https://sanlaki.shop/products/golf-club-diy-kit Walkabout Minigolf - set angle to 38Golf+ - use Sanlaki preset (currently broken, working with devs to get the alignment sorted out)

4894874/5411253To assembly you need 2 M3 Bolts & screws, im using 20mm.The hole in the club is 3.5mmPrinted in TPUNot tested in PLA ( I think it would not work because the hole where you put the controller works with friction )For the infill, i have...

An adapter to glue a broken old shaft (or a cut new one) and grip together which works in the Golf+ app for the Oculus QUest 2. Two velcro straps of 10 cm are required to mount the controller (left handed or right handed version). Can be...

This model is designed to securely mount a quest 3 (Right) controller to a golf club putter. I made this to use with ‘Walkabout mini-golf’. You can calibrate it in game by going to options, clicking on custom-grip and using the grab button to...

No Supports needed to print this model. ... This rake can be attached to your bag for easy access, it attaches to your golf club to easily rake the bunkers. ... By having your own rake we can reduce the spread of COVID.

... golf swing. PLA or PETG will work, but I used PETG for strength. Use 100% infill and increase the wall count to either 5 or 6 (at least). Attach to any golf club shaft or a trainer club like this: https://www.amazon.com/gp/product/B07NHJ1XYW/

We designed this rake attachment to try and prevent the spread of COVID at golf courses. ...Please go follow us on: Facebook: https://www.facebook.com/Riggers3D/ Instagram: https://www.instagram.com/3d_riggers/ LinkedIn:...

Quest 2 Golf Club adapter for a real golf club. I love Walkabout Minigolf and Golf+ on the Quest and this adapter adds a lot of realism to both games. This is a strong adapter, you can do a full swing without worrying about your controller...

...It’s a Remix of the Extended Golf Handle - Quest 2 If you want to make the angles perfect here is the public Tinkercad, be my guest just post it when you do. I think angles are OK as they are now. ... https://www.tinkercad.com/things/dyvYMRbhQtg

This mod holds the quest 2 controller secure at the end of a cut down club.  Adjustable weight improves swing realism.What you need:Donor club with stepped shaft 12.5mm (1/2") at the cut end.  A tapered shaft will work but will require more effort to...

This mod holds the quest 2 controller secure at the end of a cut down club. Adjustable weight improves swing realism. What you need: Donor club with stepped shaft 12.5mm (1/2") at the cut end. A tapered shaft will work but will require more effort...

This mod holds the quest 2 controller secure at the end of a cut down club.  Adjustable weight improves swing realism.What you need:Donor club with stepped shaft 12.5mm (1/2") at the cut end.  A tapered shaft will work but will require more...

This is my version of a golf attatchment made specifically for my Oculus Quest 2! I tried to make the design as similar to Deadeye VR's product as possible. So instead of spending $70 I only spent $10! The controller should fit inside the print very...

For putting / golf games on Quest2 Because this uses the original controller orientation it seems to work fine without needing pre calibration for specific grip models, which is as of today is not supported in the games I use. Gripping lower on...

golf club

I found the best success with the "CUSTOM" club in the golf+ settings and aligning the remote onscreen with the actual location of the remote on the golf club handle in real life. The dead eye works but custom seems better. The picture shows using...

Used to clip onto Quest 2 Elite Strap Tolerances are .2mm Use the same beams from original. ... Shouldn't need supports if you reorient Part A Note- Some people say that they won't be close enough to your ears, so you might try printing this remix...

I wanted to use the head strap of Quest3 with Quest2, so I made it.Please be sure to read the notes below and use at your own risk.When attaching and detaching parts, there is a possibility of damaging the VR device itself.Depending on the strength...

Please be sure to read the notes below and use at your own risk.When attaching and detaching parts, there is a possibility of damaging the VR device itself.Depending on the strength of the parts, they may break during play, causing injury or...

Working on your golf swing at the club? ...Simultaneously, you can explore Solidworks 2015/step for enhanced design and engineering capabilities.

Golf Club 3D Model Now Ready for Use. Objects Are Carefully Grouped, Making Rendering a Breeze. Every Material Is Included, Detailed and Ready to Go with All Files. If You Encounter Any Issues, Please Don't Hesitate to Reach Out to Me Directly. I'm...

This is a remix of https://www.thingiverse.com/thing:5204772. ... I needed to make it a bit stronger as it broke off at one point. There are also 2 different versions, 13.5 and 14.5 shaft diameter.

Added a why for the wrist strap to come out so it doesn't need to be removed

This mount was specifically designed for use with Walkabout Mini Golf on the Oculus Quest 2, and is intended to (more or less) map the angle of the physical putter to the in-game virtual putter. As such, it might not map as well to clubs in other...

This mount was specifically designed for use with Walkabout Mini Golf on the Oculus Quest 2, and is intended to (more or less) map the angle of the physical putter to the in-game virtual putter. As such, it might not map as well to clubs in other...

Nut attachments for porta pro speaker arms https://www.thingiverse.com/thing:4128301 to attach to this Quest 2 headstrap https://www.thingiverse.com/thing:4654433 Be aware you can easily overtighten these and break the bolt

Summary This thing is to attach your power bank to the back of your oculus quest head strap. I can recommend this not just for charging, but also for counterweight. I remix this one for my power bank xiaomi wbp15zm but you can also find more...

This thing is to attach your power bank to the back of your oculus quest head strap. I can recommend this not just for charging, but also for counterweight. I made one for my power bank xiaomi 3 but you can also use the generic plate and glue or...