quefrency middle layer 3d models

First of all, in addition to the changes required to enable the inductive Z probe I had to enable the new sensor in Configuration.h, and add a line to tell the board which pin to use for it: define TEMP_SENSOR_PROBE 1 #define TEMP_PROBE_PIN...

You can see my working firmware branch on GitHub here and modify it to fit your setup if you desire. First of all, in addition to the changes required to enable the inductive Z probe I had to enable the new sensor in Configuration.h, and add a line...

You can connect it also with printable parts which can be used in various ways (you can use it for screwing to the wall, you can use it as a holder for hanger or as a holder for hook). Printing settingslayer height: 0.25 - 0.3perimeters:...

.4mm nozzle; .2mm layer-height with initial layer at .28mm; walls I increased a bit. I did 60% infill because I wanted a little extra strength. 60mm/s travel speed. 210C nozzle temp with 60C bed temp. It came out nice on the first try. Once the...

I used 4 top and bottom layers with .25mm layer height. I used ABS for all the parts. Stiffer material like PLA or Nylon X might be better, but I tend to print everything in ABS.</p> <p>I was planning on switching out the pen holder and the spindle...

Except for the figures and token racks which are one-color, all pieces are printed as two-color by changing the color layer by layer (for example, using the M600 command, or manually changing the filament).&nbsp;MANUAL:Game content :- 1x Centre...

I also had to relocated the z-stops 20mm lower down the frame by 20mm just to make it work at all.So - not for everyone.Using Voron recommended print configuration, 40% infill, 4 walls, 5Top/Bottom layers.PETG because I could, ABS would be normal for...

Every corner must have the same amount of leds in each corner. I've used 4x leds in each corner, thats 12 led pixels per leaf → 1m of 60 leds/m = 5 leafs I would not go for more than 5 leds per corner on the 60leds/m led strip, because the strip...

You will have nearly invisible layer lines that will be more noticeable later, so knock them down now. Use a fine emery board (nail file) or a popsicle/craft stick to ensure you don't round over any facets with your fingers.Finish the ruby with a...

It would help me and the community to leave a comment on how this version works to decide whether to release it or not.The file is recommended to print vertically with a layer height of 0.12mm and a 25% infill.It is necessary to cut the ptfe tube...

Printed at .2 mm layer height with a brim to prevent some curling up at the edges - this part filled up my tiny 110 mm diameter bed. Print 2 coins and 2 moldmolds so that you can pour molds for both sides at once. This way you only have to wait...

Keep in mind superglue cures fast usually and doesn't give you much of a chance to adjust, additionally, unless you cover the exposed portion with tape precisely (if you plan on exposing it) you might get superglue there and it'll look ugly, resin...

The Heart.svg (2d) file was simply loaded into openscad and extruded like this:ranslate([0,0,rubber_base_thickness]) linear_extrude(text_thickness) scale([s,s,1]) import("Heart.svg"); (where s is an optional scaling factor).Stamp 3 Rubber Hearts.stl:...

These are the general settings I used:3 walls, .2 layer height (I use a .4 nozzle)10-20% infill (10% Lightning should be fine, even for the Racks – use something strong like Gyroid or 3D Honeycomb if you're worried about heavy items)at least 3 bottom...

Supporting this project is a guaranty for you that it will continue and become better and better.Buy MediaMan3D a...

It's only one layer of plastic so it's easy to trim out.The other bridges are just screw holes that can be drilled out. Any files with an X2 or X3 require 2 or 3 of the parts. The files right_pawl and left_pawl.stl have to be printed with 100%...

The lamp shade should, with the exception of the "antarcticphoto" theme, be sliced with layer 1=0.2mm and all other layers 0.3mm. Please adjust temperatures and material parameters for your print - e.g. the temperatures I have setup in the .3mf might...

 Do not use the following:  Using "Wipe on loops" or “Wipe on external loops” make things bad.Combination of (Retract on layer change off + Wipe while retracting off) also no good.Overhangs optimization / additional considerations.If possible, it is...

For all other parts (supports, stands, outer chain), the filament should fit snugly. Step 1: Print and clean all partsPrint one of each part, with the following exceptions:Print 4 copies of the “Water Bucket”Print 24 copies of the “Inner Chain”Print...

&nbsp; There are multiple pins to choose from in .2mm differences in thickness (the layer height). &nbsp;The hole goes on the bottom.</p><p>Inserting the spreader. &nbsp; Put the pivot platform on, with or without your platform attached. &nbsp;Align...

Achtung: Wer den ersten Layer mit mehr Fluss druckt (so wie ich), der könnte die Löcher zunächst noch etwas entgraten, die Schrauben sitzen sonst etwas stramm. Schrauben wieder eindrehen, aber nicht fest ziehen. Das Adapter sollte sich (schwer!) nach...

It's only one layer of plastic so it's easy to trim out.The other bridges are just screw holes that can be drilled out. Any files with an X2 or X3 require 2 or 3 of the parts. The files right_pawl and left_pawl.stl have to be printed with 100%...

I went 5 walls, and 6 top bottom layers.I actually used a CR6 to print most of the parts, but did print some of them on the anycubic Chiron its for. The Chiron stock is probably not worth your time, but it's my sunk cost fallacy fixer...

Look it up, or click here: https://www.youtube.com/watch?v=fcjaxC-e8oY I believe the ripples from printing are creating this theoretical boundary layer, reducing friction and back pressure by accident, helping the laminar flow and allowing for...

I printed my drawers with 0.3mm layers and a 0.6mm nozzle for optimal print time and strength. You want the rails to be straight, so do what you need to do to combat any lifting or warping, if you experience any with your printer. ...If you find the...

(While I was at it, I added proper tolerances to the clearance holes and added sacrificial bridge layers to the unsupported holes on these parts, improving printability.) Because I'd already built the machine, I'm having to go through and swap each...

UNTESTED but should be noticeably “better”, see notes laterChanged the nut slots to hexagonal to more securely capture the nutsSlots instead of captured nuts in the spider (similar to several other remixes), spaced correctly for M4 pitch and 0.28mm...

Aim for at least 3 layers top and bottom, 3 perimeter vertical layers on the walls, and around 30% infill for maximum strength. The motor has to be fitted in the correct orientation, otherwise the aluminium plate won't fit. Its wires should go...

After that, all the above pieces will fit. Revisioning: v1.0 - Initial upload v1.1 - Added "Extruder X-Axis Mount Extended" at the request of Hermy65, it should be compatible with Aaron Yourk's MK2S Rambo case. v1.2 - Updated Extruder X-Axis Mount...

Then I apply a thin layer of glue all the way around the insert. The screw is used to guide the insert into the hole, and then I can usually press it in by hand, but sometimes it requires a few taps to seat it. If it does not seem to go all the way...