quad 3d model

EX6 Arcade Fight Stick What started as just doing a few tweaks to an existing model turned into a near full redesign and a (almost) fully printable arcade/fight stick case platform; the EX6. Printable on the Ender 3 or any 200x200 printer. The...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

I considered adjusting the model, but decided to leave it as is. I'd rather have a more positive engagement that you can adjust to your liking, than end up with one that doesn't latch in place securely enough. ;)</p><p>I will leave this marked as a...

Cable clamps bolt to the Extruder mount bolts to keep the cabling tidy, which I've not used yet as I can currently only run 1 of the heaters at present (my A20M control board is a V4.1 model which doesnt have the components fitted to allow for dual...

If you want it without internal battery, I have designed this same model without the hole for the battery, remaining in measurements of 126x51x35mm, you have it here: https://www.thingiverse.com/thing:6016310 Required Components: - 1u Mini ZVS...

Tolerences are tight on this model and will require percussive pursuasion to fit a 2020 bar Base - print with inside pointing up, support the central overhang, the Ports section print as bridged ### PETG: Top- print with the inside pointing up, this...

the older model this was printed from did not have the pockets for the hex nuts so it was threaded directly into the plastic instead. Ive uploaded a reinforced version of the arm that should work better with heavier controllers.i also opened up the...

You may need to adjust your printer, sand the chamber a little, or apply some force, as the parts were modeled to fit with ZERO clearance, to assure the best possible bond when using superglue. Just apply superglue to the syringe holder anywhere...

1 slot for a pair of Kitchen shears and 1 slot for a Honing/Sharpening Steel.I designed the model into 4 printable parts so this could be printed on smaller printers like the Prusa Mini. But this also makes for easier cleaning since the bottom and...

they are built into the models. Use the provided M2.5x10mm self tapping screws by default unless told otherwise. As an alternative to jig cutting, a drawing for manual hole drilling is also provided. In addition you will need: - Hot glue...

Deck furniture is always a good way to add interest to a model. You might want to install a waterproof switch somewhere on the exterior to save having to unscrew the whole deck every time to turn it off and on. Enjoy sailing your Pocket Boat,...

I added some build notes below and a BOM which doesn't include screws, wires, connectors, etc., but has all major components.&nbsp;I planned to revisit this model and release a better version. However I have at least a year's worth of projects in...

I added a switch at the bottom of the right arm (super easy access).Please note, this system is designed to be mounted on an aluminum profile with a total width of 300mmPrints without support!Here you will find the links to the creations that have...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

A customized version of this Thingiverse model (http://www.thingiverse.com/thing:46884) was created using Customizer. ...The STL file options include: qr_rotate=0, add_sub=2, hole_r=10, hole_y=0, hole_x=30, corner_num=1, qr_thickness=5,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

Just copy your gcode to the same folder as the exe, run it, select the options you want and when you've confirmed your choice it will automatically open the first gcode in the same folder and write the temperature changes for you.Extract...

The STEP file is included for easy remixing. Please post any makes and if you see a problem please post a comment. Updates: 4-30-2020: Thanks to feedback, I corrected the model for the base, the updated version is "6I". ...None of the other parts...

&nbsp;You may have to insert a custom hole for a usb lead depending on your mounting position, this could be done in the model, or via a drill after printing.You will need to do some tweaking to keep the led matrix against the grid. &nbsp;This can be...

If you are using ceiling pipes, I've modelled the right side of the pipes only. For the left side it will need to be mirrored in the slicer. The vents part is optional but I recommend glueing it to the roof. The vents piece can act as additional...

The tubes used for processing in the Whirlwind would end up leading Ken Olson to transistors, which led to the transistorized TX-O (the love of many a tech model railroad clubber) and later to Olson founding DEC. Suddenly, the Whirlwind was the...

&nbsp;900mm in length (shown in the picture is a bit too long, you may want to use 800mm instead)The bamboo skewers seems to come in different sizes, so use the file that closest match the skewers you have and scale the model accordingly. &nbsp;If...

Winston sculpted reproduction of Schwarzenegger's face in several poses out of silicone, clay and plaster.[41] The sequences set in 2029 and the stop-motion scenes were developed by Fantasy II, a special effects company headed by Gene Warren...

Downloaded some Radio Control model yacht designs. Non of them suited my fancy for building, so I decided to come up with my own. Main Desing principles... No Keel! -> Surf Board / Windsurfer style. Light Weight (relative to size of jib!) ...

UPDATE 09.08.2022 •changed length for diffusor and mount from 10mm to 100mm •orientation changed for some models •added end cap UPDATE 12.08.2022 •added with diffusor / without diffusor comparison photo and electronics box wiring photo •added...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

No support is needed and would be very hard to remove because the support would be inside the model where the magnet eventually slides into. We are depending on bridging for the parts that would normally need support. I have given extra tolerance...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 custom_bottom_fillet_resolution = 8 stencil_horizontal_position = 50...

The design is made for an E12 bulb socket, but the "Bulb Holder Mount.stl" part could be easily modified in modeling software or simply by drilling new holes to line up with a bulb socket of your choosing. I am considering using an E12 smart bulb to...

Update 220811:Added solid with 1deg step on requestReplace the code below to this, (BB and CC changed to 2 and 1 and replace STL to the new...