qrp labs qcx case 3d models

This is my attempt at a case for the excellent QRP Labs QCX transceiver, and I'm new to this so maybe you can improve on the design. The design criteria was to case a QCX that had been built to the manual with controls all mounted on the board. I...

This design offers an improved top front case part (and accessories) for the specified model found on Thingiverse at https://www.thingiverse.com/thing:2661221. The primary goal with this updated design was to overcome the limitations of the...

With my QCX-Mini just finished, I designed a set of tilt feet for the QCX-Mini, based on my QCX+ tilt feet design. These tilt feet allow a better view angle when you have the QCX-Mini on your desk or table. I couldn't use screws because the bottom is...

This is a very simple chassis to support a QRP Labs QCX-PA2 power amplifier. If you build the amplifier kit without an enclosure, the large heat-sinks are joined to the PCB only via the tabs of the power transistors, so everything can move around a...

This is a very simple chassis to support a QRP Labs QCX-PA2 power amplifier. If you build the amplifier kit without an enclosure, the large heat-sinks are joined to the PCB only via the tabs of the power transistors, so everything can move around a...

This is a very simple chassis to support a QRP Labs QCX-PA2 power amplifier. If you build the amplifier kit without an enclosure, the large heat-sinks are joined to the PCB only via the tabs of the power transistors, so everything can move around a...

This Case Makes a High Capacity QCX Battery Pack Possible: Li-Ion 14.8V 7650 mAh You Can Accommodate 12 Batteries of Type 18650 (3.7V / 2550 mAh) Here Arrange Them in Three Parallel and Then Four in Series to Achieve 14.8V The Recommended Voltage for...

This is the case I built for my trusty QCX transceiver from QRP Labs.

Housing for the QRP Labs QCX+ (plus) CW Transceiver https://www.qrp-labs.com/qcxp.html Currently in progress …..

One has the text QRP Labs and QCX-Mini in raised text and the other is without text. Use whichever version suits you. It should be printed vertical with one of the ends on the print plate and might need a brim for support depending on how good...

... Die Rückseite befindet sich noch in Planung ;) Looking around in the WWW for a QCX+ Hounsing I only found this one : https://www.printables.com/de/model/65299-qrp-labs-qcx-plus-housing Thanks for the work. I modded a little so it fits my needs.

A hole for the built-in key is adjusted so when using it, the top part of the case acts as a stop for the key, providing better keying experiences and making it easier to use. Knurled buttons, particularly on the VFO more than AF, enable easy...

This is a custom bumper case designed specifically for the QRP Labs QCX transceiver available at qrp-labs.com/qcx.html. I aimed to strike a balance between protecting the radio and keeping it easily accessible during our work on it. ... No specific...

This is a stand/bumper case I designed for the QRP Labs QCX transceiver https://qrp-labs.com/qcx.html. I wanted to provide some protection for the radio, but keep it accessible as we worked on it. No specifics on print settings, but you will need to...

This is a case for the latest (as of 2024-07) version of QRP Labs' QDX transceiver.I printed it with the smallest sides on the print bed with no supports, and had no problems. If you don't choose where the seams go they can get pretty ugly, make sure...

... to protect the QDX at least a bit from physical use and abuse. :) The pumpers get attached to the original aluminum case. ... The rear bumper also covers the BNC connector, so it is less likely to put stress on it when carrying it loosely in a bag.

I loved pshuman's design for the QRP Labs QCX transceiver stand on Thingiverse (https://www.thingiverse.com/thing:2607304) and thought, "Why not create a matching accessory?" So, I built an Anderson Powerpole connector with a convenient on/off switch...

A case and cover for the QRP Labs 20 watt, 50 ohm dummyload. It is designed for a 0.4mm print nozzel which allows the cover to slide into the case tight enough that nothing else is needed to secure it. ...Print vertically with no support required.

... there's room for future expansion if needed (such as an internal rechargeable battery system). Clock kit: https://www.qrp-labs.com/clockn.html QLG1 GPS kit: https://www.qrp-labs.com/qlg1.html Push switch: any type, 7mm thread diameter. ... Enjoy.

This enclosure is designed specifically for use with QRP-Labs Ultimate3/3S beacon's GPS module, and it's yours to use at no cost. It's a straightforward box with a basic design. One thing to note is the absence of a pre-drilled hole for the...

Case for QRP-Labs clock kit that utilizes supplied 2 x 16 LCD display, optional GPS module available. Slightly smaller than previous design posted (thing:3899560) using larger 4 x 20 LCD screen. Front panel filament color can be changed at layer 16...

I verified my measurements and ensured all holes were in correct locations to confirm fitment of internal PC boards before creating a custom case for QRP-Labs' GPS Clock kit, which does not include a case. This design is specifically tailored for the...

When you are testing with the QRP-Labs 20W dummy load ( http://shop.qrp-labs.com/dummy ) you have to look out that you don't put it on metal or have small pieces of wire laying around. To prevent sparks and magic smoke I designed a simple 2 part case...

My version of case, for this fantastic little portable transceiver.Built-in foldable stand, 2 parts deisgne, no glue needed. When assembling drop in control buttons, then insert VFO button in top part opening, press fit PCB, after that simply...

A remix of the original QRP Labs box: https://www.thingiverse.com/thing:3955678I have added the following to the original design:Rounded cornersFront text "Satellite clock"Mains socket hole for a three-pin clover leaf ICE connector C5Hole for an...

My version of case, for this fantastic little portable transceiver.Built-in foldable stand, 2 parts deisgne, no glue needed. When assembling drop in control buttons, then insert VFO button in top part opening, press fit PCB, after that simply add...

More info on this kit radio can be found here: https://qrp-labs.com/qcx.html To build this case you will need (in addition to the 3D-printed parts): (4) m3x6mm screws (4) m3x16mm screws NOTE1: The 2 knobs are designed to compensate for the different...

Heavily revised version of an earlier design I created, which can be found on Thingiverse (https://www.thingiverse.com/thing:3899560).\r\n\r\nThe programming switches have been relocated to the back of the case for improved access, and the front...

Simple enclosure with angle brackets for this fantastic qrp transceiver. Donations for new trx are more than welcome via paypal

... has 2 drilling templates for drilling the 2.5mm holes and used a M3 thread cutter. But short M2.5 bolds can be used also (just look out for the display and display PCB).. More info : https://www.ph2lb.nl/blog/index.php?page=qrp-labs-qcxp#tilt