qidi xcf pro 3d models

I would like to use the universal spool filler system as a top mount for the Qidi Q1 Pro.https://www.thingiverse.com/thing:3020026https://www.printables.com/model/825275-filler-spool-holder-2020-mountAnd I have a lot of 2020 extrusion profiles lying...

I discovered a sharp edge on my Qidi x-pro cover and the feeder tubes were rubbing against it, causing wear. To round off that corner, I created this part. It needs to be rotated in place. I printed the rounded section down (no supports required) and...

This spool holder is specifically designed for use with the QIDI X-Pro, featuring M10x1.5 threads that provide secure compatibility with Push Plastic spools. A major advantage of this custom-made holder is its ability to accommodate spools wound in...

THIS IS A REMIX I've modified the files to match the Qidi X-pro perfectly. They should work great and still allow for the top to be securely attached. I've only tested two of them on the right side, so I'm unsure if all four bins will fit with the...

Designed for the Qidi X-Pro original. Remixed to make the heights work with the original hotends instead on the high temp ones which are shorter. Scale the 8mm shroud to 99% as it allows a better fit in the duct. Needs 30mm M3 bolts whereas...

QIDI X-Pro Front power switch

Upper Spool holder for QIDI X-Pro

FILAMENT GUIDE ASSEMBLY FOR THE QIDI X-PRO 3D PRINTER

This is a PTFE tube cutting jig for the QiDi Tech X-Pro dual nozzle printer.

Those gaps also need to be blocked, blocking only the exhaust port will have little effect.I might make a tpu gasket in the future to help make more of a seal.Related Models:Qidi Q1 Pro Exhaust Port...

Qidi X-Pro Raspberry Pi Camera Mount This is a remix, with huge thanks to: Dwiekawki https://www.thingiverse.com/thing:3809015 TheOddArtisan https://www.thingiverse.com/thing:1156296 You can also check Qidi X-Pro Raspberry Pi Zero Case Mount here:...

I ran in to a 40mm inner spool reel that is too small for the stock spool holder on my qidi x-PRO. ...So I made 1 to fit the 40mm spool hole

Filament guide to fit the new QIDI X-pro 3D printer. It pulls the filament away from the edge of the spool. Also, to avoid leaping off the filament around the spindle. ...No supports needed for printing.

Filament guide to fit the new QIDI X-pro 3D printer. It pulls the filament away from the edge of the spool. Also, to avoid leaping off the filament around the spindle. ...No supports needed for printing.

Filament guide to fit the new QIDI X-pro 3D printer. It pulls the filament away from the edge of the spool. Also, to avoid leaping off the filament around the spindle. ...No supports needed for printing.

I custom designed it, and it is totally adapted to the QIDI X-PRO printer model 2019/2020. The use is particularly useful if you have set up a device to move the wire outlet away from the bottom of the printer wall with a guide. ... In all cases, the...

Just a quick and dirty remix of the FlashForge Creator Pro dual fan duct by DrLex to fit my Qidi X-Pro. The height between the cooler (on the left) and the 2 nozzles had to be increased by about 1cm so the air comes straight to the underside of the...

The noticeable dip at the top of the Qidi X-Pro's build plate was a major concern for me. It appeared as though the two sides were curving inward, which only exacerbated my worry that they might not be properly aligned. ...This simple upgrade aims to...

This is an excellent foundation for the QIDI X-Pro printer. If you make any enhancements, consider remixing or leaving a comment here to inform others about your changes. Update 2018-07-20: Calibration tweaks were made to retraction and extrusion...

A custom magnetic tool holder designed to seamlessly integrate with existing fasteners on the Qidi X-Pro printer's side. It may also be compatible with other Qidi models, thanks to its adaptable design. The offset between these fasteners measures...

The Stock QIDI Tech 3D X-Pro printer sets itself apart with its exposed circuit board, visible behind the touch screen panel, a feature not found in the QIDI Tech 1 model. This design choice poses significant risks of accidental damage from metal...

This upgrade fully encloses the hood of the QIDI X-Pro, ensuring successful prints for high-temperature filaments like ABS. It also reduces fume escape when printing with materials such as ABS. Since this component sees intense heat, I printed it in...

Modification of a QiDi X-Pro filament guide "adapter" allows the filament to feed from mid-roll instead of from up against the printer back. Is a mod of someone else's design but can't remember where I got it from and their design was too hard for me...

the default attachment of the wire guides of the QIDI TECH X-PRO printer (model 2019/2020) is glued to the bulkhead, which sometimes causes problems. This model allows the thread guide attachment to be offset from the middle of the spool and mounts...

Unfortunately, there was no bracket available to attach it to my Qidi X-Pro printer so I designed one myself. It works flawlessly. The design requires an M10 x 16mm bolt that can be easily obtained at a local hardware store. With a pair of...

Qidi X-Pro Storage Bins: 1. Front-right bin with glue stick holder 2. ...Back-right bin with utility holder Special thanks to: sparker3d for the original design https://www.thingiverse.com/thing:3336055 CARINA for their contribution...

Spool holders on the Qidi X-Pro can fit a spool up to 70mm wide, making it ideal for spools weighing up to 1kg. Larger spools of 2kg filament are typically wider. These Extended Spool Knobs provide extra room by adding 35mm, 25mm, or 15mm to...

The Qidi X-pro has a dual nozzle setup. On my unit, one nozzle was lower than the other so Qidi instructed me to use a paper shim to compensate. That brought its own problems. I couldn't find an exact thickness shim to use, and the shim was...

This is a precision cutting rig for PTFE tubing that interfaces seamlessly with the QIDI X-Pro nozzle. I utilize this setup to trim Capricorn tubing to precise lengths. The capricorn cutter featured in one of the images functions flawlessly with this...

I upgraded my qidi x-pro to the all metal hotend. I purchased the hotend direct from Qidi and they sent me some instructions to tweak. They sent me a version of this fan duct, saying the new hotend may sit higher. For whatever reason, my nozzle...