qidi x pro 3d models

Print on it's side with support between the feet (as per diagram in "QIDI X-Plus X-Max Ribbon Cable Bracket by humebeam ") Printed in PLA+, has enough flex. Post-printing, just needs sharp edges smoothed. Note: with any back clip, on the X-PLUS,...

This is a Bowden Tube Connector for the QIDI X-Plus and X-Max extruder covers. Just remove the screw from the top cover, place the connector and screw it in place with a 20 mm M3 screw. It is compatible with 6.0 mm PTFE tube, same dimension as the...

Thanks :)https://www.paypal.me/humebeamengineeringAboutThis is a Hygrometer / Thermometer Holder that snaps onto the rear chamber fan cover of the QIDI X-Max and X-Plus. It was requested by one my followers. It might fit other printers as well.BOM -...

Version history3.0:Bracket angled towards extruder cover to keep the cable from dipping down.You may have experienced that over time the cable will dip down using the V1 and V2 brackets, this angled design will prevent that.2.0:Improved version that...

I increased the size of the cable access because my cable would not fit. ...Guessing Qidi may have changed the cable size.

I broke my spool holder so made another and it fits the Qidi perfectlyAlso fits all standard rolls of filament. I used Tree Supports and printed in PLA

I purchased the Qidi X-Max in December 2021 and these carriages fit models of this period. The bearings are 29mm L, 19mm O.D., 10mm I.D. Probably fits the X-Plus from the same period, but I cannot confirm this. My system was making unsettling...

It also fits stock printers of course.It should also fit QIDI X-Plus and I-Mate (and I-Mate S) but I've only tested it on my X-Max.BOM - Bill of MaterialsI buy most of my 3D printer parts from quality stores on AliExpress and Banggood. Shipping takes...

About Draken is a high flow dual channel fan duct for the QIDI Tech X-Max and X-Plus. In order for you to use it, you need the new extruder carriage. I have attached a picture so you can tell if you have the new carriage or not. If you don't have it...

About Gripen is a high flow fan duct for the QIDI Tech X-Max and X-Plus. In order for you to use it, you need the new extruder carriage. I have attached a picture so you can tell if you have the new carriage or not. If you don't have it installed in...

About This is a support bracket for the Qidi X-Plus and X-Max ribbon cable, it attaches to the top extruder cover. Without support, the cable dips down when it gets extended, causing unnecessary stress on the cable as well as it getting greasy from...

You will not be able to use the top hat with large spools. The xtensions should sit with a tight fit in the original holders. The mod worked for me as a quick intermediate solution until I finished my piggyback- spool holder. Print Settings Printer:...

This is a recessed cover designed to close the large opening in the Qidi X-Max & X-Plus printer top covers, allowing for filament spools to be accommodated without excessive pressure. Additionally, I created a 30mm to 50mm spool insert that helps...

This is a Hygrometer / Thermometer Holder that snaps onto the rear chamber fan cover of the QIDI X-Max and X-Plus. It was requested by one my followers. It might fit other printers as well.</p><p><strong>BOM - Bill of materials</strong></p><p>You...

About This is a filament cleaner and backspin preventer for the QIDI X-Plus and X-Max. It was originally designed for one of my other designs but I never included it there. To use, print the two parts. Cut a piece of sponge and place it inside the...

AboutThis is a filament cleaner and backspin preventer for the QIDI X-Plus and X-Max. It was originally designed for one of my other designs but I never included it there. It should fit all printers using a 6 mm bowden tube as well.</p><p>To use,...

Bob Martin in the Qidi 3D FB group owns an X-Max and says it fits his also, otherwise, there is another pi-cam mount you may want to check out here if you think this one is in the way too much: https://www.thingiverse.com/thing:4347548 I'm using the...

Step file is available if you want to make any changes.Be sure level the bed afterwards.Print SettingsPrinter:QIDI Tech X-MaxRafts:&nbsp;NoSupports:NoResolution:&nbsp;0.15 mmInfill:30 %Filament: Prusament PC Blend Orange&nbsp;&nbsp;Notes:&nbsp;I...

AboutThe Adjustable Spool Holder for QIDI X-Plus and X-Max works with most filament spools up to 1 Kg. It uses common 608 roller bearings (search for 608ZZ or 608RS, I bought 4 for €4) for a smooth rotation of the filament spool. The spool holder is...

3:1 BMG Extruder) // New PID values // tested code in Octoprint M303 E0 S220 C10; // returned: bias:105 d:105 Ku: 37.659279 Tu:21.200001 // returned: Kp: 22.595568 Ki:2.131657 Kd:59.878258 // Send updated PID M301 P22.595568 I2.131657 D59.878258; //...

To upgrade, you only have to reprint this part, the other parts are unchanged: qidi-xplus-xmax-extruder-fan-duct-404020-part-2-ribbon-cable-holder-1.1.stl About This is an alternative to my QIDI X-Plus X-Max Advanced Extruder Cover:...

The files added are: external-rod-holder-left-tall-1.0.stl external-rod-holder-right-tall-1.0.stl About The Adjustable Spool Holder for QIDI X-Plus and X-Max works with most filament spools up to 1 Kg. It uses common 608 roller bearings (search for...

About This is an advanced Extruder Cover for the QIDI X-Plus and X-Max. The original cover didn't have much space for a larger fan (although a 40 mm fan just about fits) and was lacking a few other features. The cover has the following features:...

Required purchase - 40mm x 10mm 24v fan. Some sanding of carriage material also required in order for lower duct scoop to fit between extruder and carriage housing. Quick print. Recommend filament that withstands high temps, Nylon, ASA or...

I bought mine here: https://www.amazon.com/gp/product/B07JG7DS7V/ If they are out of stock the specs are: Inner thread size M3 x 0.5 Outer thread size M5 x 0.5 Length 6mm This is primarily for people who would want to print these parts out in resin...

Made this spool holder extension to be able to mount large spools on the stock spool holder of my X-Plus (i think this should also work with the X-Max). Insert the extensions on top of the fully extended spool holder rods and then place the spool...

Some time back I converted my Qidi X-Pro over to a Lerdge K setup and went from the standard dual extruder to a single extruder and wanted to stabilize everything now that the top plate didn't have a second stepper to rest on. I recreated the factory...

This is support for inner tube 8 mm of Qidi X-Plus printer.

This is support for inner tube 8 mm of Qidi X-Plus printer.

To get my printer leveled precisely, I purchased a dial gauge for 18 euros. ...I then printed out a test sheet and attached it to the guide rails to check the bed's accuracy.