qidi x plus 3d models

My design for a tool-box for QIDI x-plus You can place the supplied tools ... and whatever else you like ;-) ... ...in this box that hangs off the side of the printer

Toolbox designed specifically for the Qidi X-Plus, drawing inspiration from the impressive designs of car7er.

Qidi X-PLUS support to filament dryer EIBOS, after print I made some upgrades to improve the stability. ... You need supports only on the piece that connect to the printer filament support Printed with 4 walls and 15% infill

Qidi X-PLUS support to filament dryer EIBOS, after print I made some upgrades to improve the stability. ... You need supports only on the piece that connect to the printer filament support Printed with 4 walls and 15% infill

The Qidi X-Plus 3D printer has a Spool holder that is a little difficult to install. I was also unable to use the filament spools sold in Brazil because it has a diameter of 48 mm and the Qidi spool holder is 49 mm in diameter. ...So I decided to design...

I recently encountered difficulties installing the Spool holder on my Qidi X-Plus 3D printer, which led me to investigate alternative options. Unfortunately, the filament spools sold in Brazil proved incompatible with the printer due to their 48mm...

Spool holder for the Qidi X-Plus uses factory spool holder cradles to secure mounts, working in either direction with tube on rear top or over machine top with cover on. Spool width is approximately 3-1/2 inches, placing a standard spool about 5...

This puts a standard spool hanging about 5 inches behind the machine. This was remixed from another remix holder made for another machine I believe the original was 1832235 just searching back. You will need: Both mount sides(they are mirrored). 4 of...

A filament guide for the Qidi X-Plus (X-Max?) , which replaces the original and can also be used with the hood closed. For mounting, the filament guide is simply pushed from behind into the original holder. Through the small hole at the front end,...

Spool Holder for Qidi X-Plus Machine. This design utilizes factory spool holder cradles to securely fasten the mounts, allowing it to be used in either direction - either by attaching the tube to the rear top or positioning it over the machine's top...

... Halter zum befestigen einer Box am X-Plus ohne bohren. ... Sie werden in die beiden Schlitze in den Griffmulden eingeklipst. A holder for attaching a box to the X-Plus without drilling. They are clipped into the two slots in the recessed grips. ...

cooling fan duct for qidi x-plus This fan duct is only a replacement part for the original design. ... (there are different designs for qidi x-plus, so it should look like this one)

Blink Camera Mount for the Qidi X-Plus 3D printer. ...This mount attaches to the back left bar and puts the camera in front of the fan.

This is needed if you close the hole in the hood with for example @humebeam QIDI X-Plus X-Max Top Cover https://www.printables.com/model/59198-qidi-x-plus-x-max-top-coverPretty simple design, print on it's side, no support needed, take the original...

The original spool mount by Skiid dosent fit the new QIDI X-Plus 2 printer. This is my first remix but the mount fits great. The part that I changed was the little hook part of the mount. ...

Modeling was done using Blender, while printing was accomplished with QIDI X-Plus. Before initiating the print job, verify that the scale is accurate to avoid any potential issues. ... Printing Details: Material: PLA Infill Percentage: 80% Layer...

I remade this design to work on the Qidi X Plus 3. Not the best solution because the front door is not flat so it takes some fiddling to get a decent view. Qidi tells me that they are working on a camera upgrade. ...So, consider this a temporary...

... enclosure for their carriage. I've included the gcode I used to print it on my Qidi X-Plus. Worked perfectly with PLA. ... Also included is the Autodesk Inventor file I used to make it, if anyone wishes to make their own modifications or changes.

About QIDI X-Plus X-Max Wingnut Extender is an extender for the wingnuts that secure the bed leveling screws on the QIDI X-Plus and X-Max. I found the wingnuts to be annoyingly small so you don't get any force to unlock it and it was also not at all...

Mount to hold Sunlu filament heater on back of Qidi X-plus, may work with Xmax as well. holds heater so when running long prints with PETG you can keep the filament dry and with as least exposure to moisture as possible. First upload to Thingiverse...

This is my second version of a Qidi X-Plus camera mount, purposefully designed to hang down in front of the printer for an excellent view of the build process. I have included photos showcasing the mount as it's positioned on the front of the...

QIDI X-Plus 2 Dial Indicator Mount using a dial indicator from my local Menard's. Stem size .375". ... ...

... really that easy. Printer: QIDI-Tech x-Plus Resolution: fine (0.2mm) Support: yes / 70° Print temperature: 190°C Bed temperature: 60/50° (first layer / rest of print) I'm excited to share this ruggedized spool roller with the QIDI X-Plus community!

This is an upgraded version of the Qidi X-Plus 3 Carbon Filter that comes with the new models. This may require modifications of the back panel. If you don't currently have the carbon filter installed there is a template and instructions that are...

This revised design is specifically tailored to work seamlessly with the original Qidi X-Plus roller, ensuring it stays securely in place. Initially, I had used mistertech's spool weight, but it often failed to provide sufficient grip on the...

After a year of almost daily use, the plug-in connection to the heating bed of my Qidi X-Plus said goodbye without comment. See photo. Fortunately, the power of my ancient Weller soldering station was sufficient to solder the pin strip back on...

It is a simple way to get filament rolls to turn easy on the QIDI X-Plus. I had problems with the original piece that holds the bearings. They seemed a little thin and I couldn't slide the QIDI spool support rings over them either because it's a...

I had to slightly rework the holes for the ends of the Qidi-Spool-holder-Rod. Print Settings Printer: Qidi X-Plus Rafts: NoSupports: No Resolution: 0.4Infill: 15% Filament: 3DJake EcoPLA Matt Grey Notes: Printed with 0,6mm Nozzle. ...Don't print...

Awesome Very low resistance Spool holder for Qidi Tech X-plus 3d Printer Makes printing TPE and other exotic filaments a little easier, the bearings lowers the resistance when pulling from the spool. Printed 100% infill for my own use, all parts.

I recently got my Qidi X-Plus and decided to use the internal spool holder to print some ABS. Unfortunately, the new cardboard spool filament holders offered by many filament makers fall off of the back of the spool holder and get caught between the...