qidi x one 2 3d models

Additional materials required: * 1m or 1.5m (depending on the position of your RPi) DSI/CSI 15 pin flat flex cable (please ping me if you find one with good EMI shielding) * 8x short M2.5 screws to attach the display to the adapter (should hopefully...

This is a replica of the nameplate situated at the front of the QIDI X-one2 printer, featuring an embossed logo and text that protrudes 1mm from the surface of the nameplate.

Filament guide to fit the new QIDI X-pro 3D printer. It pulls the filament away from the edge of the spool. Also, to avoid leaping off the filament around the spindle. ...No supports needed for printing.

A filament holder for the Qidi X-Smart printer. Perfect for those with limited space behind their printer or who prefer to print TPU materials. ... Simply screw it into place using the original screws behind the left handle.

Filament guide to fit the new QIDI X-pro 3D printer. It pulls the filament away from the edge of the spool. Also, to avoid leaping off the filament around the spindle. ...No supports needed for printing.

Qidi X-Max Tapo C100 Mount Please only use the spot to mount your camera like I did. ...otherwise you could possibly crash your camera or damage your printer.

The camera from Qidi for the X series printers suffers from some pretty bad glare. ...This sub 13-minute print will make your camera look so much better. Be caution of your material choice due to internal chamber temps.

I ran in to a 40mm inner spool reel that is too small for the stock spool holder on my qidi x-PRO. ...So I made 1 to fit the 40mm spool hole

Filament guide to fit the new QIDI X-pro 3D printer. It pulls the filament away from the edge of the spool. Also, to avoid leaping off the filament around the spindle. ...No supports needed for printing.

Designed to help assist with bed leveling for Qidi Tech. X-Plus. Squares are large format 50x50mm and printable area is 250x180 mm. ... Designed to be printed on a single layer with a .04mm nozzle at .02mm layer height.

I prefer using the lower filament holder for filament in my Qidi X-Max, but after a short time, the filament started rubbing against the ribbon cable during use. I couldn't find any filament guides for this area online, so I created one to solve the...

Qidi X-Pro Storage Bins: 1. Front-right bin with glue stick holder 2. ...Back-right bin with utility holder Special thanks to: sparker3d for the original design https://www.thingiverse.com/thing:3336055 CARINA for their contribution...

I custom designed it, and it is totally adapted to the QIDI X-PRO printer model 2019/2020. The use is particularly useful if you have set up a device to move the wire outlet away from the bottom of the printer wall with a guide. ... In all cases, the...

Hi 3D printing fellow, this is a test pattern to evaluate the levelling of the printer bed for the 3D printer model X-MAX by QIDI. The STL file will have the pattern shown in the images. With standard settings in the slicer software the print...

CHANGELOG V.1.2 - First published V1.3 - Tested for 50 hours of printing with good results - Improved clearance of the ribbon cable - Slightly reduced length of the cable guard - Added a little pillar at the radial fan to provide contact for the...

AboutThe QIDI X-Max Modular Tool Holder is just like it sounds a modular tool holder system for the QIDI X-Max that attaches with a spring design to one of the handles in the printer.The base has two slots for attachments, I made a few different...

About The QIDI X-Max Modular Tool Holder is just like it sounds a modular tool holder system for the QIDI X-Max that attaches with a spring design to one of the handles in the printer. The base has two slots for attachments, I made a few...

It also allows to connect the QIDI filament sensor (without the “+” pin as shipped by QIDI for the X-Max). Intercept PCBBecause the V4.6 mainboard doesn't connect the pin 8 of the flex cable anywhere, another way has to be be found to interact with...

You could use a nut with loctite but don't tighten it.BOM - Bill of Materials1 x Rubber Band with a suitable length (I used an elastic hair band my daugther donated)2 x M3 Hex Head Cap Allen Bolt (16 mm)1 x M2.5 allen / hex key OR 1 x M3 Hex Head Cap...

A way to mount the eSun eBox to the QIDI X-Max. As main attachment It uses the filament canal and the screw below at the back of the x-max. It all prints without supports but you'll need ~9x M3 x 10mm Screws e.g.

Awesome Very low resistance Spool holder for Qidi Tech X-plus 3d Printer Makes printing TPE and other exotic filaments a little easier, the bearings lowers the resistance when pulling from the spool. Printed 100% infill for my own use, all parts.

Designed to help test bed level settings on Qidi Tech X-Plus. 3 rows of 50x50 mm squares to show where adjustments are required. Designed to be printed with a .04mm nozzle at .02mm layer height. ... Printable area is set to 250 x 180 mm

They are a generic camera that is often marketed under different names, like Ultimo, at MicroCenter.It is designed to mount in the rear of the printer, along the stamped metal rail.This was inspired by the LogiTech C270 mount by HammerAndAnvil,...

I have included photos showcasing the mount as it's positioned on the front of the printer and a photo of the camera attached to the mount, clearly displaying the printer printing a new mount for the Qidi X-Pro which will be featured next. No...

Modeling was done using Blender, while printing was accomplished with QIDI X-Plus. Before initiating the print job, verify that the scale is accurate to avoid any potential issues. ... Printing Details: Material: PLA Infill Percentage: 80% Layer...

This is a precision cutting rig for PTFE tubing that interfaces seamlessly with the QIDI X-Pro nozzle. I utilize this setup to trim Capricorn tubing to precise lengths. The capricorn cutter featured in one of the images functions flawlessly with this...

This is a spool holder to attach filament rolls on the side of a QIDI X-Max 3 printer.I created it to be compatible to the modular tool holder of @humebeam which unfortunately didnt hold well on my X-Max 3 printer (see...

A custom magnetic tool holder designed to seamlessly integrate with existing fasteners on the Qidi X-Pro printer's side. It may also be compatible with other Qidi models, thanks to its adaptable design. The offset between these fasteners measures...

The Stock QIDI Tech 3D X-Pro printer sets itself apart with its exposed circuit board, visible behind the touch screen panel, a feature not found in the QIDI Tech 1 model. This design choice poses significant risks of accidental damage from metal...

"board-fan-mount-V2-10mm.stl" is for generic 40x10mm fan (ie, the stock24V Qidi fan) Stock Qidi fan sounds like a 12V fan run on 24V :p noisy Rearrange wires to make things neater and reduce wire strain. ... May need to flip the ribbon cable back up...