qidi x max 3d models

left side guard. ...no logo

Русский У меня сломался шкив мотора оси X на Qidi X-Max. Производитель принтера пришлет шкив только через две недели. Пока сделал свой. Спасибо за помощь мистеру ddddiii...

QIDI 3D X-MAX holder for spool. ...Required bearing ABEC 5 (6, 7)

I increased the size of the cable access because my cable would not fit. ...Guessing Qidi may have changed the cable size.

Required purchase - 40mm x 10mm 24v fan. Some sanding of carriage material also required in order for lower duct scoop to fit between extruder and carriage housing. Quick print. Recommend filament that withstands high temps, Nylon, ASA or...

<p>to have the write friction please print with 4 walls 50% infill petg or abs.</p><p>please use support, you can remove them with the help of a cutter</p>

For the original printhead with 40mm fan. I swapped the very loud fan for a much quieter one. In order to ensure sufficient airflow for cooling, I use these two parts. So far no problems. ... You need 2x M3x30 screws A 40x40x20 fan also fits...

Please hold off if not too late :( This is a remix of Chad's Dragon Mod for the QIDI X-Plus/X-Max. I wanted to learn how to use Fusion360, so this was one of my challenges to get familiar with the program and have some fun. The original design was...

This is just a simple stand I designed for the QIDI Max printers to be able to print directly from filament dry boxes. My printer is the Max II so it came with a filament breakage sensor, which the stand straddles and is held centered. If you have...

This is a simple spacer that will raise your build plate guides (rear and side) after installing QIDI's soft magnet. The build plate guide is normally lost after the installation of the soft magnet.If you're not familiar with what the part is...

My final solution to my X-Max 3.I removed the runout sensor completely, as I do not need it.This bracket mount in the original place, where the runout sensor was mounted.I designed two versions. One with PC4M10 Couplers. ...This is for changing the up...

One holder which is a non intrusive holder which can be mounted/clamped on the front edge plastic of the x-Max (mountable upwards and downwards), the second one you need to cut out a part of the plastic frame in order to accomodate the 2nd holder,...

... 3D printer (I do!). The Left and Right Roller frame files for the X-MAX are different than the X-Maker (https://www.thingiverse.com/thing:4752731) files. The X-Max files have a longer Support going don the back of the printer. ... Good luck!!!!

... but for nice clean fit... the metric works better. The maximum width of a roll of filament is 3-5/8" If you do both of these modifications, (the roller and the Bowden tube) I think you'll love your X-Max 3D printer (I do!). ... Good luck!!!!

The stock filament spool holder on the X-Max falls woefully short of expectations. Planning to redesign it entirely, a temporary solution is being offered to improve its performance. Only two affordable 608 roller bearings are required to achieve...

The mount slides easily around the center crossbar underneath the X-Max bed, and I have it pulled back towards the door to avoid bumping into the extruder cover when the bed is all the way up. The recessed circle holds the two-sided tape and metal...

... on a counter close to the ceiling. ...Also the original bearing holders broke off when I printed the design so I replaced those with a holder for two 6mm x 210mm Metal Tubes. ...Just add some heatshrink on the tubes to make it hold inside the bearings.

IMPORTANT: This is a remix/update/improved version of the HERCULES carriage done by HumeBeam Changes/improvements compared to original "HERCULES" carriage: - Hotend cooling completely redesigned, tuned and optimized to utilize a 100% of the...

Well, standard Extruder is not really running smoothly without a special fan duct as well as a ribbon cable holder. I designed a new riboon cable holder. ...Fanduct as well as vent clip from Humebeam.

Tested only with PLAPrinted with .4 nozzle, .2mm layer height, 2 walls and Arachne enabled.The following changes were made to the original design:Extended out the mounting hole for more room behind indicatorAdded fins to allow for repeated use...

What do you need: Bondtech Dual-Gear Drive for 5mm Axis (DRIVEGEAR-KIT-175-5) 1x M3x25mm for clip axis + 2x washer (thickness ca. 0,6mm) - one under the screw-head one under the clamp. 2x M3x30 for cooling-block Also i would change the...

This piece fits snugly at the entrance of the printer cover's upper portion. ...It should effectively resolve issues related to filament snagging, as well as enhance the process by which the filament is directed into the extruder, thus eliminating the...

Created a custom cable restraint for my xmax to protect the hotbed cable. There are others out there, but my bed had thicker dimensions so I chose to create my own. This design requires 2 tie wraps to secure the cable to the retainer. Others...

a simple box to accommodate the hotend

2 parts for easy printing Remixed from by mistertech Thingiverse: https://www.thingiverse.com/thing:3375047 by Jelliott526 Thingiverse: https://www.thingiverse.com/thing:4794054

Small Thingi to cover the hole in the acrylic cover and still use the filament on top. ... Please rotate by 90° before printing so that the tube is touching the buildplate too.

Designed this 30mm fan shroud/adapter to concentrate the small fans cooling on the heat-pip e heatsink to help prevent heat creep on the high temp extruder. This fan mount replaces the two 9mm spacers on the 30mm cooling fan. Only additional...

2mm lower tool head for Triangle Labs K500 volcano heater.  This heats way better and allows way more flow.  I suggest using this specific 5015 fan the application.  I tried some other ones and they were not very good.  Use superglue to gasket the...

Simple power cable support. My dogs while playing would sometimes pull the power cable out so I needed a quick fix. ... Needed is one very small cable tie.