qidi x max 3d models

Thanks to the original designer for the Spool Holder accessory. Works like a charm, pulls filament much easier than built in option and makes spools easier to swap. My issue is that it pulls filament a little too easy and noticed the potential...

I'm trying to harden up my Qidi Tech into a solid brick by redesigning the end supports to be sturdier and longer. These should fit snugly onto the 10mm rods with just a slight press. I'll need new screws for the lower stepper and mounting. Now I...

In an attempt to stiffen up my Qidi Tech into a complete brick, I recreated the end supports (shown sitting on the platen) to be beefier and longer. Should be sized to produce a slight press fit on the 10mm rods. Will require new screws for the lower...

Screw this to your wall to move the Qidi dry box from the back of the printer to any place easier to access.

I designed these custom shoes for my QIDI Tech-1 3D printer, utilizing Hatchbox's versatile TPU material to create a unique and functional design.

It makes the exit hole larger allowing the switch to open even when filament is still flowing through the sensor.The model replaces the small exit hole with a 6mm hole that allows a 6mm x 6mm threaded insert (M4 screw size) to be heat sunk into the...

36 x 12,5mm dice box with Shadowrun logo. ...V.2 = Top cover holder now improved Print Settings Printer: QIDI X-MAX Rafts: No Supports: No Resolution: 0.15 Infill: 25% Filament: Das Filament PETG baige Category: Dice

I made this adapter for SUNLU and ColiDo brand filaments that have a larger diameter spool hole than other filaments. ...This allows the filament to roll on the qidi spindle instead of resting on the bottom of the dry box.

Automatic power shut-off is triggered immediately when the QIDI Tech 1's extruder fan comes to a stop. ...The SSR25DA control module handles this critical function with precision and reliability.

I love my Qidi X-Maker 3D Printer, however, the filament guide design has been problematic. The factory guide is just a flexible plastic tube that snaps in to a channel. I have had the tube pull out of the channel many, many times during long...

3D printable lanyard badge holder for your office, school, or any other use! ...Easy and Fast to print (on my Qidi X-max, it takes 40min). ...Fits most standard US sized IDs and still allows the RFID for door access.

3D printable lanyard badge holder for your office, school, or any other use! ...Easy and Fast to print (on my Qidi X-max, it takes 40min). ...Fits most standard US sized IDs and still allows the RFID for door access.

I'm giving it another shot at creating a custom housing for the Raspberry Pi camera within my Qidi X-Max 3D printer setup, and I've managed to get hold of a wide-angle adapter that fits perfectly.

https://www.thingiverse.com/thing:4441076 Fanned Guitar Bridge Saddle. ...Print Settings Printer: Qidi X-Max Rafts: No Supports: No Resolution: 200 Infill: 40 Filament: Overture PETG Black Category: Other

... the holder. The magnetic portion goes under the bottom half of the hinge, and the shim goes under the top half to keep the cover flush. Works great in combination with my QIDI Tech I Magnetic Door Latch https://www.thingiverse.com/thing:4908773

... the holder. The magnetic portion goes under the bottom half of the hinge, and the shim goes under the top half to keep the cover flush. Works great in combination with my QIDI Tech I Magnetic Door Latch https://www.thingiverse.com/thing:4908773

... well on the Flashforge as well. Designed using Solidworks 2016, I've included the 3D model in both Solidworks and IGES format. Print Settings Printer: Qidi Technology Rafts: No Supports: No Resolution: 0.2mm Infill: 30% Notes: Printed in PLA

Printed on a Qidi Tech 3D printer using red ABS material, this spacer boasts a sturdy construction that does not require the use of rafts or support materials. The design is optimized for maximum strength and durability, ensuring a secure hold even...

A set of vents I designed to cover the rear gap in the Qidi i-fast. Printed in a Tough PLA. ... Here is a link to a Video that shows them in more detail as well as some other mods: https://youtu.be/OVrCpiJO6EY

The QIDI printer's standard endcaps are excessively bulky, necessitating that they be unscrewed before swapping filament. These endcaps provide a minimal 2mm lip to prevent the spool from slipping off and enable rapid installation of most...

I'm designing a new clip for my QIDI 3D printer after the original ones snapped under the weight of the wire bundle. ...The current setup seems to be holding up just fine despite being quite snug, giving me hope that this redesign will prove successful.

The clear door on my Qidi Tech I (2018) printer cracked. I precision-cut a replacement using my laser cutter. Although the measurements aren't flawless, the result is still passable. Use 0.1 inch or 2.5mm clear plastic to replace the door. ...Adjust...

Qidi I-mate (not Imate S) do not have covers for the top sides or front.   This is an attempt to make a suitable front cover suitable for temperature sensitive filaments.   You need a large printer to print this. ... I used a Longer LK5 proI strongly...

Magnetic Door Prop for QIDI Tech Printer Works Perfectly with Flashforge and Markebot Tired of Losing the Door Prop, Now I Have a Secure Solution I designed this magnetic door prop to attach easily to my QIDI Tech printer. It also works great on my...

I would like to use the universal spool filler system as a top mount for the Qidi Q1 Pro.https://www.thingiverse.com/thing:3020026https://www.printables.com/model/825275-filler-spool-holder-2020-mountAnd I have a lot of 2020 extrusion profiles lying...

My new Qidi Tech 1 was eager to soar because of the sleek new design on her side and front panels that refused to stay shut, so I took matters into my own hands and built a clip to secure them in place and prevent drastic temperature fluctuations.

Cam Mount for Microsoft Life Cam at Bed Level on QiDi Tech 1. REV1: Short Version We simplified the design to make it more user-friendly. REV2: Added a Longer Boom with Bolt to Secure It To prevent the boom from moving around, we added a sturdy bolt...

I made this tool tray to hold various accessories that came with my Qidi printer as well as markers and things. ... The holder has room for: - Leveling card - Scraper - 6" scale - 2 small pliers or cutters (one flush cut & one needle nose in...

This simple clip keeps the rear panel of the QIDI Tech 1, 3D printer securely in place without obstructing the movement of the extruders. Without some sort of restraint, the wings of the rear panel tend to push inward and interfere with the printers'...

The X-Max (X-Plus) heated bed cable can get stuck between the Z-Axis limit switch and the bed leveling the bed.This small print gently pulls the cable away from the limit switch to minimize the likelihood. ...It hooks on the back left frame upright and...