qidi x max 3d printer

CHANGELOG V.1.2 - First published V1.3 - Tested for 50 hours of printing with good results - Improved clearance of the ribbon cable - Slightly reduced length of the cable guard - Added a little pillar at the radial fan to provide contact for the...

The standard Qidi X-Max spool holder is unfortunately uncomfortable to use and creates a lot of friction when unwinding, for example because the axle diameter is much smaller than the inner diameter of the spool. I have tried to improve all the...

\r\n\r\n====================\r\nCons:\r\nYou lose some X Y and Z space.\r\nX284 Y240 Z290\r\n\r\n====================\r\nBuild tips:\r\nUse CF-nylon for printing. Don't use PLA or...

QIDI X-Max Dragon Hot End Remix This is a remix from https://www.thingiverse.com/thing:4630835 I have made the following changes: - The mounting location for a 40x40 mm l/h hot end fan is moved for 7 mm to the inside. - That fan has now a third...

Redesigned Z limit switch mounting for the Qidi X-Max (may also work on X-Plus, but have not confirmed dimensions). This design brings the switches closer toward the front in order to clear the lip of the steel platform when mounted upside down. ...

Users of the QIDI X-Max have reported an issue where the head's rapid movement from front to back causes the filament to move backward through the bowden tube, resulting in the filament unspooling and tangling on the spool support arm. A simple...

Just a simple design of a eSun and Sunlu filament dryer box holder for the qidi xmax.

I designed that holder for the X-Max to use bigger spools. ... Should fit on the X-Plus too.

I've worked around the missing control pin by using some flex cable to connect the control pin of the BLTouch to either the WiFi socket of the mainboard or an raspberrypi: The klipper configuration for for an raspberrypi on GPIO27 (not recommended...

I've tweaked Alex's initial design, but the tube was way too long to fit my full filament roll snugly inside the X-Max lid and it kept shifting around. I had to shorten that tube and adjust the opening to match the size of the black feed tube that...

this are qidi original hot end carriage what i got from email when contacting Linda. ... Im share this becomes before I can found any in internet, now you can have it and if want, can make own mods.

... This will make the filament spool spin perfectly! Filament rolls with an inner width from 40mm to an outer width of 70mm can be used. The left and right frames are the old ones. Print Settings Printer: X-Max Rafts: No Supports: Yes Infill: 20%

Updated 2022/12/11: Improved printability by enlarging the radius of corners touching the build plate.Updated 2022/11/7: Lowered the belt clip profile, beefed up the X-Axis motor mount, and increased the adjustment range of the Y-Axis limit switch...

... Thingiverse at https://www.thingiverse.com/thing:4245806. ...This updated model boasts enhanced stability and features an innovative stop mechanism designed specifically for seamless insertion into the Qidi Aloy tube, ensuring a secure fit every time.

QIDI replaced the factory bed magnet system with a PEI with an attached magnetic base. ...When the base is glued in, it is raised high enough so that the PEI guides are high enough so that they do not act as a stopper.With this simple mod, we recover...

As you can see on the pictures, the original filament guide from Qidi fits into the cable glands. The probe is from my BBQ ;-) It's a bit tricky to change filament, but unrolling of the filament works very well with no struggles and the angle of the...

The shortened BMG handle was still too tall and ran into the side of my printer so I made one that is a bit shorter. I also found that the idle gear was just rubbing so expanded that area. My wiring looks pretty bad, so I extended the skirt on the...

Time Lapse Camera Mount for Action Cameras: A Seamless Solution for Flawless Footage Mounts easily onto the front tray of X-max, synchronizing perfectly with the print bed's up and down movements to capture stunning time lapse footage. Optimal...

I've switched from the original Qidi Extruders to [humebeam](https://www.thingiverse.com/humebeam)'s [Icarus 2.1](https://www.thingiverse.com/thing:4968938) due to massive problems with the print quality. This switch also allowed me to add various...

Placchetta in PLA per Copertura del PCB Interno del Display come Protezione, si Maschiano M3 i due Perni sotto al PCB e con N.2 Viti M3 x 20 si blocca il tutto.

Designed a trash container, that fits inside the printer. ...Print in two parts and glued together.For bottom 2 magnets 6x3mm can be used.Added a short and long version.

A longer spool holder is designed to store and utilize spools of up to 1 kilogram in size within a printer. ...Two versions are available, each offering distinct advantages: one features printed threads for secure spool storage, while the other reuses...

This piece fits snugly at the entrance of the printer cover's upper portion. ...It should effectively resolve issues related to filament snagging, as well as enhance the process by which the filament is directed into the extruder, thus eliminating the...

This is a replica of the nameplate situated at the front of the QIDI X-one2 printer, featuring an embossed logo and text that protrudes 1mm from the surface of the nameplate.

I found a 3D printer farm that mounted Stovetop Fire Stop units on the shelving above his 3D printers. I don't have shelving above my 3D printer so I came up with this solution. I made this to install to the cover for my QIDI X-Plus and X-Plus II....

-Qidi X-Max -Qidi X-Plus ________________________________________________________________________ Since I don't feel like always ordering the PTFE hose from QIDI, I have now designed this easy way to cut your own PTFE hose. With the following...

... the original cooling duct intake. ...This modification will not only delete the initial cooling duct inlet but also replace the extruder cover due to its substantial thickness, which can serve as a surface for the X-axis limit switch to push against.

... three Wingnut Extenders, one for each bed leveling screw. The model is very easy to print and supports are not needed. The Wingnut Extender will also fit other 3D printers using similar wingnuts (M4), but I have only tested on my X-Max.

Qidi X-Max (X-Pro) ribbon cables are easy to replace when using these clips to manage the cable. These clips may work on other Qidi printers as well.There are three kinds of clips:Upper back frame railSide corner frame railBottom side frame railAlso...

You will not be able to use the top hat with large spools. The xtensions should sit with a tight fit in the original holders. The mod worked for me as a quick intermediate solution until I finished my piggyback- spool holder. Print Settings Printer:...