qidi x max 3d printer

I was let down by Qidi's "baggage handle" spool holder because it generates a lot of friction that causes inconsistent extrusion, particularly with flexible filaments. A swift trip to Tinkercad and we have a solution ready! It requires two (total)...

... available options: b8 (8mm ID), b8.05 (8.05mm ID), or b8.1 (8.1mm ID). The more precise your printer is, the narrower the inner diameter you can use effectively. ...On my CR-10S, I've found 8.05mm to be the perfect fit for printing with accuracy.

The photos show one printed in white for illustrative purposes, but you can print any color since the part is only visible if you're looking from inside the printer. ... The face is 1mm thick and the rim is 2mm thick, and is designed to sit on the...

Made this mount for my Quidi One X to mount a Xiaomi Xiaofang IP cam. Clip it on the buildplate and attach the cam to it. Print Settings Rafts: No Supports: YesResolution: 0,2mm Infill: 15% Category: 3D Printing

Simple storage for filament snips that hang on to the top groove of the X-Smart 3.

I tried Elphwrkz filament sensor case but it didn't fit my printer. ...I guessed my printer is a newer version so I created a new version for new machine.

This is a little modification for original X-Plus Extruder Fan. ...Print this model then replace from two stand-off to this fan duct.

Any filament should work but would use something more temperature tolerant than pla. ... Might have to clean up surfaces to get magnets to sit perfectly level with build plate.  18 are needed for the x-plus build plate.

There is a lot of unused space inside the printer walls, before I just had them laying on the bottom but they could get knocked around under the bed. This holder wedges between some of the plastic of the left wall to stay in place. ... I printed with...

There is a lot of unused space inside the printer walls, before I just had them laying on the bottom but they could get knocked around under the bed. ...This holder wedges between some of the plastic of the left wall to stay in place.I printed with low...

Like it says, these allow you to put a 150x170mm glass bed on the X-Smart to replace the famously terrible magnetic plates (that are $30 to replace now). To attach, fully remove the bed-level screws, place these on top of the springs, and reattach. ...

Revised the dimensions, to move the spool closer to the X-Plus top cover. Printed this from ABS (base) and PETG (rollers). 608 bearings fit perfectly. ...The holder is very robust and much more convenient to use compared to the original.

Simply tilt the compact leg to latch it onto the underside of the handle, then position it securely on the printer. It can effortlessly move front-to-back on the printer, yet remains firmly in place side-to-side. Adding a small piece of magnetic tape...

This Thing created by BrayChristopher really solves a problem I have with my printer. The filament tube clips on the back of my machine do not function properly and the filament gets bound up at the spool. The clips still don't work but this device...

Made this simple riser block for the top lid on my X-max3. Didn't want to take the lid of when printing PLA so this was a simply fix for that. It has two small taps that slots into the holes in the frame. ...It fits both in the front and in the...

I created this modified spool holder because I was constantly experiencing jamming issues with the original one that comes with the printer, and I noticed a lot of people complaining about it online. The pieces are carefully designed to fit together...

I made this because I kept having jamming issues with the original spool holder that comes with the printer, and I saw a lot of complaints about it online. The pieces are designed such that they all fit together. ...The tolerance should be tight...

Please check out https://www.thingiverse.com/thing:3715393 Additional parts: • 1 x 6" tie-wrap • 1 x M4x20mm button head screw and nut for blower fan • 3 x M4x35mm button head screws and nuts for front and rear clips Modification: • Cut the tie-wrap...

Does not occupy more space, cover can be closed.Buy a 4010 style fan (like this one)Slice and print the included holder (xsmart3_4010fan.slt)Turn off the printer, place on the side, remove the bottom coverLocate the mainboard fan, disconnect, unscrew...

... have a higher heat tolerance. Remove screw at center top front of printer. You will need a longer one, but not too long. It could interfere with the top of the print head enclosure during printing. ... PRINT HEAD TEMP = 230C BED TEMP = 70

Here is the picture of it mounted inside the printer with the bearings: https://photos.app.goo.gl/AuxXoPKSRjs7Zi1u6 Printing: Disable coasting to print thin sections better if using PETG which has a better bond strength between layers. Print with...

the white 5050 LED strip in the front of the X-PLUS doesn't really show you what is happening at the nozzle. Is ok for gneral viewing.. The LED strip can be cut into 3 sections, and connected with extension wires if you want to put them in a few...

Printed with Nylon CFYou need to cut a slot in side of the cover to make room for the probe. Also it´s recomended to use threaded Inserts for 3D Prints to make it work. The CR Touch is plug and play.

Things you need.The 3D-ModelSealing tape. (I had one lying around)FAN_SPACER_v1.stlhttps://www.thingiverse.com/thing:6237118Thanks to D3adKennyAir Filter for Flashforge Adventurer 4 Series, 80x80x10mm, e.g. AliexpressYou can use the original...

Hi all, Due to space constrain in the office, I had to mount the filament on the side.Just looking around for spool holders and thought i should just practice 3d modeling and use the mount from another designer.2 type of spool holderUsing the...

... stop for homing. This modification also helps improve prints by reducing the load the machine has to deal with during acceleration and increasing available airflow. Print Settings Printer: QIDI X-One Rafts: No Supports: No Resolution: .3 Infill: 10

So, I was having problems with filament jamming on my new QIDI X-Max High Temperature hot end. It's possible that all I needed to do was raise the temperature or change some settings, but I bought a Micro Swiss hot end, found it to be 5.3 mm too...

The Armor Parts, often called the Third Armor or Max Armor, are four parts that form an armor for X that can be obtained from Light Capsules in Mega Man X3. Each part also has an enhancement chip to improve its abilities, but X's system can handle...

...The Main Block piece is designed to snugly fit into the handle openings on the side of the QIDI X-Max. It has a groove that allows any one of the other pieces to be slotted into it and will fit left or right handle opening (curved corner goes down).

DescriptionSpace - X capsule of elon musk rocket for Mars travelling. ... No plugins required, ready for production...