qidi x max 2 3d models

... the original cooling duct intake. ...This modification will not only delete the initial cooling duct inlet but also replace the extruder cover due to its substantial thickness, which can serve as a surface for the X-axis limit switch to push against.

-Qidi X-Max -Qidi X-Plus ________________________________________________________________________ Since I don't feel like always ordering the PTFE hose from QIDI, I have now designed this easy way to cut your own PTFE hose. With the following...

There are a couple of options:Adjust the print area: use NotePad or other text editor to create a gcode file with the following then copy it to your USB Flash drive and run it like any other print file.          ; Set XY...

**MOVED TO PRUSA:** https://www.prusaprinters.org/prints/155501-qidi-x-max-x-plus-internal-filament-guide-v2 This internal filament guide set works with X-Max and possibly the X-Plus. It replaces the simple OEM vertical guide with a 4mm ID X 6mm O.D....

It is a phone mount for the Qidi tech X-max and X-plus. You would need to use attached custom start and end g-codes in Cura (or whichever software that allows them). Otherwise the extruder will hit the mount during initial priming. ...

It is a phone mount for the Qidi tech X-max and X-plus. IMPORTANT: You will need to use attached custom start and end g-codes in Cura (or whichever software that allows them). Otherwise the extruder will hit the mount during initial priming. ...

Qidi X-Max (X-Pro) ribbon cables are easy to replace when using these clips to manage the cable. These clips may work on other Qidi printers as well.There are three kinds of clips:Upper back frame railSide corner frame railBottom side frame railAlso...

AboutQIDI X-Max X-Plus I-Mate (S) Wingnut Extender is an extender for the wingnuts that secure the bed leveling screws on the QIDI X-Plus and X-Max. I found the wingnuts to be annoyingly small so you don't get any force to unlock it and it was also...

Version history3.0:Bracket angled towards extruder cover to keep the cable from dipping down.You may have experienced that over time the cable will dip down using the V1 and V2 brackets, this angled design will prevent that.2.0:Improved version that...

It also fits stock printers of course.It should also fit QIDI X-Plus and I-Mate (and I-Mate S) but I've only tested it on my X-Max.BOM - Bill of MaterialsI buy most of my 3D printer parts from quality stores on AliExpress and Banggood. Shipping takes...

About This is a support bracket for the Qidi X-Plus and X-Max ribbon cable, it attaches to the top extruder cover. Without support, the cable dips down when it gets extended, causing unnecessary stress on the cable as well as it getting greasy from...

About Draken is a high flow dual channel fan duct for the QIDI Tech X-Max and X-Plus. In order for you to use it, you need the new extruder carriage. I have attached a picture so you can tell if you have the new carriage or not. If you don't have it...

Filament spool holder and filament guide arm for the Qidi X-Max... I'm a fan of the X-Max printer, but the supplied spool holder rod and feed mechanisms leave something to be desired. I wasn't able to find anything online as a replacement quite to...

Updated June 2022This carriage fits the Qidi X-Max (X-Plus) where the bearings are 29mm L, 19mm O.D., 10mm I.D.The stock Qidi X-Max carriage it is a pain in the you know what to switch between the low temp to the high temp extruders.This design moves...

After getting frustrated with every adapter and modification I've tried for my Qidi X-Plus, and X-Max, I have tried most of the prints and only found one mod that works (yet motion isn't as smooth as I'd...

Print on it's side with support between the feet (as per diagram in "QIDI X-Plus X-Max Ribbon Cable Bracket by humebeam ") Printed in PLA+, has enough flex. Post-printing, just needs sharp edges smoothed. Note: with any back clip, on the X-PLUS,...

Thanks :)https://www.paypal.me/humebeamengineeringAboutThis is a Hygrometer / Thermometer Holder that snaps onto the rear chamber fan cover of the QIDI X-Max and X-Plus. It was requested by one my followers. It might fit other printers as well.BOM -...

This is a Bowden Tube Connector for the QIDI X-Plus and X-Max extruder covers. Just remove the screw from the top cover, place the connector and screw it in place with a 20 mm M3 screw. It is compatible with 6.0 mm PTFE tube, same dimension as the...

Step file is available if you want to make any changes.Be sure level the bed afterwards.Print SettingsPrinter:QIDI Tech X-MaxRafts: NoSupports:NoResolution: 0.15 mmInfill:30 %Filament: Prusament PC Blend Orange  Notes: I...

3:1 BMG Extruder) // New PID values // tested code in Octoprint M303 E0 S220 C10; // returned: bias:105 d:105 Ku: 37.659279 Tu:21.200001 // returned: Kp: 22.595568 Ki:2.131657 Kd:59.878258 // Send updated PID M301 P22.595568 I2.131657 D59.878258; //...

I purchased the Qidi X-Max in December 2021 and these carriages fit models of this period. The bearings are 29mm L, 19mm O.D., 10mm I.D. Probably fits the X-Plus from the same period, but I cannot confirm this. My system was making unsettling...

Make sure you feed the filament from below the spool through the black filament guide tube.BOM - Bill of Materials2 x 608ZZ roller bearings1 x M3 or M4 screw and bolt (15 mm) (optional, you can use the stock screw and nut)What to printPrint the...

Made this spool holder extension to be able to mount large spools on the stock spool holder of my X-Plus (i think this should also work with the X-Max). Insert the extensions on top of the fully extended spool holder rods and then place the spool on...

About Gripen is a high flow fan duct for the QIDI Tech X-Max and X-Plus. In order for you to use it, you need the new extruder carriage. I have attached a picture so you can tell if you have the new carriage or not. If you don't have it installed in...

To upgrade, you only have to reprint this part, the other parts are unchanged: qidi-xplus-xmax-extruder-fan-duct-404020-part-2-ribbon-cable-holder-1.1.stl About This is an alternative to my QIDI X-Plus X-Max Advanced Extruder Cover:...

About This is a filament cleaner and backspin preventer for the QIDI X-Plus and X-Max. It was originally designed for one of my other designs but I never included it there. To use, print the two parts. Cut a piece of sponge and place it inside the...

This is a recessed cover designed to close the large opening in the Qidi X-Max & X-Plus printer top covers, allowing for filament spools to be accommodated without excessive pressure. Additionally, I created a 30mm to 50mm spool insert that helps...

This is a Hygrometer / Thermometer Holder that snaps onto the rear chamber fan cover of the QIDI X-Max and X-Plus. It was requested by one my followers. It might fit other printers as well.</p><p><strong>BOM - Bill of materials</strong></p><p>You...

The files added are: external-rod-holder-left-tall-1.0.stl external-rod-holder-right-tall-1.0.stl About The Adjustable Spool Holder for QIDI X-Plus and X-Max works with most filament spools up to 1 Kg. It uses common 608 roller bearings (search for...

I just recently converted my Qidi X-Plus over to a Lerdge K setup like my X-Pro. I wanted to keep the FFC ribbon cable setup but add the auto leveling functionality now available to me. I tinkered with several addon mounts but none of them seemed...