qidi tech xone 2 3d models

Name: Smart_House_Illumination_Package_2 Version: Beta_Test_Versions_Offer Preview: Currently_Under_Development Units: Centimeters Dimension: 67.41 x 67.411 x 100.29 Polys: 50016 XForm: Enabled_With_Optimization_Options Box_Trick:...

I lost track of the source code for the camera, so I apologize for that. This time around, screws are unavoidable; please consult the original model for screw sizes. To keep things straightforward, I designed the PI3 case to be inserted into the...

Filament Spool holder for XIDI X-PRO, see picturesJust print and use. ...No support needed.

This is a remix of FlashForge Nozzle Light V2 by frasersnow. I use an Arducam that sticks pretty far into my printer, so I couldn't use frasersnow's front back plane, so I used the rear back plane instead. However, even that didn't work well for me...

Decided to craft this component to prevent filament tubes from coming into contact with the primary harness of the extruders during printing. This part also helps to eliminate tension and pulling on the main wiring harness. The design was engineered...

I needed a piece to be mounted at an angle on the front right corner so it could fit perfectly with my cable chain setup. ...Ultimately, I had to settle for a modified version that was trimmed back significantly, but I managed to make it work by adding...

I added properly spaced mounting pegs to the filter design by https://www.thingiverse.com/watchthis The filters are cut to fit from purchased air filters. ... I used ...

I got tired of not having a dedicated spot for my Raspberry Pi Camera, so I decided to build a bed mount to hold it securely. I created a custom camera mount that locks tightly onto the bed arm, ensuring a snug fit. Since I already had some extra...

A protective shield for the microSD card slot that keeps dust at bay.

The extruder cable consistently slips out of place during print jobs, but a simple adjustment to the printer's enclosure resolves the issue effectively. By readjusting the cover mid-print, users can prevent further complications and ensure...

You should cut the bottom of the J1's silicon nozzle cleaning pad a little bit to shorter and cut the outer protrusion of the quiditech box' lid and fill it with silicon etc. so as to seal it. ...Also better just cut the inside protrusion of the box'...

I didn't like how the original stopped me from putting the bottom piece back on, so I did a new design in fusion360 to use the offset of the OEM bracket lowering the fan enough to get the bottom plate back on. Used TOBSUN EA60-12V (sold on amazon...

Here's my version of a thing that will offset the filament guide tube on the back of the X-One. The main goal was to place the guide tube at roughly the center of the spool so that filament doesn't get pulled at weird angles. To print this, you...

I tweaked crazybasic's Replicator boot script. The print bed matches the miniature Chinese 3D printer's specs. I also swapped out the measurement system for millimeters and inches. ...Additionally, I applied the scaling factor to the enclosure.

I think these should be the default on any printer, as the lock nut system is annoying, and the printers that have no lock nut, well lets say, is frustrating to have to keep adjusting bed level as the dial has moved. ... These have a fine ratchet...

This is firmware for a BigTree-Tech Biqu B1 3D printer. I have enabled Mesh bed leveling 3 points if you have a warped bed. Mesh Bed leveling reference: https://www.youtube.com/watch?v=vcxM7-VK44k&ab_channel=TeachingTech To flash this to...

QiDi printer coil holder screw knob

Sci-Fi City dystopia City Ruin Tech 2 3D model

Jupiter Ancient tech temple Space station 2 designs ! ...3D!

Direct Drive Extruder mount for Eryone ER20 Print Settings: 4 to 5 Walls 4 Top 4 Bottom 20 % infill Extra part needed will be longer stepper motor cable like this...

I remixed this design from Thingiverse: https://www.thingiverse.com/thing:421510. I tweaked the mounting plate so the light stays put, no longer pivoting on that rear screw. It's now securely attached flush with the plate. To keep everything in...

Customized version of https://www.thingiverse.com/thing:2132775 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2132775

Big Tree Tech Relay v1.2 Board Dimensions Only ------------------------------------------------------- The Big Tree Tech Relay v1.2 is a model that showcases its board dimensions. Designed specifically to aid in creating custom mounts, this file...

Needed a mount for some Big Tree Tech Endstop Mount for 1/2" EMT conduit for Piper 1 3D Printer. Printed .20 resolution, 2 perimeters, 30% infill.Need x3  6-32 x ½" Phillips Head Screwsx1   6-32 x ¾" Phillips Head Screwx2  6-32 Nyloc Nutsx2   6-32...

User Created Mostly Machined CNC / Multi-Tool Laser and Cooling System Mount for J-Tech Photonics 2.8 W, Equipped with a 40MM Fan; Although the Cover Fit Is Somewhat Loose, It Still Functions Properly.

Needed a mount for some Big Tree Tech Endstop Mount for 1/2" EMT conduit for Piper 1 3D Printer. Printed .20 resolution, 2 perimeters, 30% infill.Need x3  6-32 x ½" Phillips Head Screwsx1   6-32 x ¾" Phillips Head Screwx2...

This is a drive lever for the Hi-Tech 548-25 SSDD Floppy drive used in the Kaypro 2.This lever may work for any floppy drive with a 4.75mm shaft.Included is an STL model with STEP CAD file.