qidi tech x one2 3d printer

This Project is a modification of Rolandooo's "Qidi X-One Side Holder" designed specifically to accommodate a Meco USB vacuum, effectively capturing stray filament fragments that accumulate beneath the print bed of my Qidi Tech X-One 3D printer.

I remixed this cooling duct to fit the Qidi Technology X-Max because there are not very many options for upgraded cooling ducts. I recommend printing it in the orientation I have it placed in. Just use 85 degree supports "everywhere" and it will only...

I remixed this cooling duct to fit the Qidi Technology X-Max because there are not very many options for upgraded cooling ducts. I recommend printing it in the orientation I have it placed in. Just use 85 degree supports "everywhere" and it will only...

Made an adaptation specifically tailored for use with my QIDI 3D printer.

I discovered a sharp edge on my Qidi x-pro cover and the feeder tubes were rubbing against it, causing wear. To round off that corner, I created this part. It needs to be rotated in place. I printed the rounded section down (no supports required) and...

This is a PTFE tube cutting jig for the QiDi Tech X-Pro dual nozzle printer.

Designed for the Qidi X-Pro original. Remixed to make the heights work with the original hotends instead on the high temp ones which are shorter. Scale the 8mm shroud to 99% as it allows a better fit in the duct. Needs 30mm M3 bolts whereas...

THIS IS A REMIX I've modified the files to match the Qidi X-pro perfectly. They should work great and still allow for the top to be securely attached. I've only tested two of them on the right side, so I'm unsure if all four bins will fit with the...

Hangs on the side of QIDI Tech One Printer Print instructionsUnassociated tags: Elmers Glue Category: 3D Printer Accessories Summary A hanging holder for Elmer's Glue Stick (0.77 oz(22g)). ...Hangs on the side of QIDI Tech One Printer Print Settings...

Spool holder for the Qidi X-Plus uses factory spool holder cradles to secure mounts, working in either direction with tube on rear top or over machine top with cover on. Spool width is approximately 3-1/2 inches, placing a standard spool about 5...

They must be so accurate that the fittings push down on the pipes so much that they are tight, but do not bend.So it is here that "Distance Meter PTFE for Tube Qidi X-MAX Hot End" comes into the picture, to get the pipe length exactly correct.To...

Back Plate for Qidi X-Max 3.Allows replacemenr of noisy motherboard fan by a quieter and bigger one 60x25.Material : PLAQuality : standard, 0.2 layer heightInfill : 15 %Support : snug for the left partNo Brim, Mickey’s ears to prevent warpingLeft and...

I've recently created this item and I'm not certain if it's been done before, but I think it might be useful for others who own a Qidi Tech 1 and X-Pro printer. I tested it on my Tech 1 and found that it fits a standard 1kg printer spool snugly, with...

Spool Holder for Qidi X-Plus Machine. This design utilizes factory spool holder cradles to securely fasten the mounts, allowing it to be used in either direction - either by attaching the tube to the rear top or positioning it over the machine's top...

IMPORTANT: This design is based on Hercules - QIDI X-Max Carriage done by member humebeam. Not sure if this counts as an actual remix since most of the original design has changed and the complete carriage remodeled. <i>All the firmware instructions...

FILAMENT GUIDE ASSEMBLY FOR THE QIDI X-PRO 3D PRINTER

FILAMENT GUIDE ASSEMBLY FOR THE QIDI X-PRO 3D PRINTER

fit's exactly to this cam and the qidi-Xplus only snap in and use a long flat cable and your ready for surveillance your print. ... https://www.amazon.de/MakerHawk-Raspberry-Nachtsicht-Kamera-einstellbar-Fokus-Modul-Himbeer-pi/dp/B071718FDK

This simple adapter fills the space between a Qidi holder and a standard spool, like SmartSaint or Polymaker. Its measurements are inside 30mm and outside 52mm - not fully circular to provide some grip. Two additional adapters were added, one with...

I've designed a simple solution for covering metal-sided printers like the X-One. Using 3/32 Lexan and some magnets, I created protective covers that can be easily attached to the case. These materials were all sourced from Home Depot. To secure the...

Then insert the black 6 mm tube that comes with the printer and guide the filament through it.Print SettingsPrinter:QIDI Tech X-MaxRafts:&nbsp;NoSupports:YesResolution:&nbsp;0.16 mmInfill:25%Filament: Fillamentum ABS Black&nbsp;Notes:&nbsp;Print it...

Just some covers for the X-One or any other metal sided printer. I made these from 3/32 Lexan and some magnets. All items purchased from home depot. I just used some CA glue to carefully attache the magnets to the Lexan and the hold nicely to the...

I needed a way to attach my Wyze Wi-Fi camera to something sturdy, so I found this mount that fits perfectly on the front of the X-Plus printer. It lets me secure the camera using either the adhesive strip that comes with the Wyze cam or by screwing...

This is a tool box that fits into the carry handle of the X-Max printer. Partially print the handle insert to gauge size and use your slicers scaling to decrease or increase as needed for both parts. Its a press fit and will depend on the material...

This is a tool box that fits perfectly into the carry handle of the X-Max printer. To ensure a snug fit, partially print the handle insert to gauge its size and then use your slicer's scaling feature to adjust both parts as needed. The tool box will...

This Qidi fan duct is a remix of humebeam's Gripen 1.4 fan duct. I was using his creation for several weeks with no issues. But then one day i looked and saw that the output side was warping and hanging a little lower than the bottom plane. So I...

If I were to do it all over again, I'd probably have just gotten a nicer 3D printer from Modix instead of trying to retrofit my QIDI X-Max. Since time has become pretty scarce and valuable for me lately, I won't be updating or watching this thing...

... myself to design a compact container that can be attached to each side of my trusty X-One. ...This clever holder will securely stash the entire toolkit that came with the X-One, along with extra supplies like glue sticks, rulers, and other handy items.

It was designed, size-wise, to be used with the "Qidi Leveling Nut" but will of course also work without it: https://www.thingiverse.com/thing:4806871 The Wingnut Extender will also fit other 3D printers using similar wingnuts, but I have only tested...

... without jam nuts. Simply adjust and then let go - no need to worry about anything moving out of place! They'll likely work on other printers too, and the hole and hex recess can be modified to accommodate different screw and nut combinations.