qidi spool holder 3d models

A basic spool clamp specifically designed for use with the Qidi Tech XMAX or XPLUS spool holder, boasting a 30mm diameter design.

Spool holder for the Qidi X-Plus uses factory spool holder cradles to secure mounts, working in either direction with tube on rear top or over machine top with cover on. Spool width is approximately 3-1/2 inches, placing a standard spool about 5...

Spool Holder for Qidi X-Plus Machine. This design utilizes factory spool holder cradles to securely fasten the mounts, allowing it to be used in either direction - either by attaching the tube to the rear top or positioning it over the machine's top...

This puts a standard spool hanging about 5 inches behind the machine. This was remixed from another remix holder made for another machine I believe the original was 1832235 just searching back. You will need: Both mount sides(they are mirrored). 4 of...

... ...These endcaps provide a minimal 2mm lip to prevent the spool from slipping off and enable rapid installation of most spools.\nThis design was created using Tinkercad. ...You can edit it online at https://www.tinkercad.com/things/5e6gX7vF3yW

Spool spacer for the X-One. ...ID 31mm, OD 51mm, Width 97mm. V2 updated with single bevel for improved print quality. Print Settings Printer: Qidi Tech X-One Rafts: No Supports: No Resolution: .20 Infill: 10 Post-Printing Before and After

Simple tool holder, fits into the Qidi i-Mate S build space.

This compact disk takes the place of the bigger disk on the spool holder. With this disk, you usually won't have to remove another disk to swap it out for a new one. ...Simply reuse the bolt that came with your machine for this upgrade.

This is a versatile tool holder compatible with Qidi Tech I, Flashforge Creator Pro, and other printers featuring a gap between the frame and side panel. ...The tool holder securely clips onto the printer's side panel and comes equipped with slots to...

for the Qidi plus. ... 608-2RS Ball Bearing you would need on sides.

Filament holder parts for Qidi Tech i-mates. ... A smooth filament holder can be created by combining an M8 285mm screw and Quick Change Universal Spool Holder available at home centers.

For the Qidi direction, you need to feed the filament in a specific way, and the issue arises when you tighten the spool holder screw. This causes the flange to bind 70 mm spools, preventing them from turning. If you leave the spool fastening screw...

Simple spacer that allows wider filament spools (such as HatchBox) to fit on the Qidi Tech 1 spool holder.Print instructions:Layer height: 0.20 mmInfill: 20%Supports: None

This is needed if you close the hole in the hood with for example @humebeam QIDI X-Plus X-Max Top Cover https://www.printables.com/model/59198-qidi-x-plus-x-max-top-coverPretty simple design, print on it's side, no support needed, take the original...

Spool holders on the Qidi X-Pro can fit a spool up to 70mm wide, making it ideal for spools weighing up to 1kg. Larger spools of 2kg filament are typically wider. These Extended Spool Knobs provide extra room by adding 35mm, 25mm, or 15mm to...

I didn't like the spool holder on my QIDI I-Mate because it let the filament jump off a full spool when parked and it had too much drag and wasn't easy to change. This design requires you to remove the right side plastic piece from the top of the...

The component needed to sit snugly on the build plate and fit perfectly within the large spool holders of my 2016 Qidi tech model. Initially, the part was one solid piece, but I encountered an issue with supports that were constantly getting knocked...

The QiDi X-Max printer is a relatively solidly built printer in general, except for the wobbly, pop-up style "travel case handle" spool holder. This upgrade corrects the shortcoming in design and prevents overall movement of the spool arrangement...

The original spool mount by Skiid dosent fit the new QIDI X-Plus 2 printer. This is my first remix but the mount fits great. The part that I changed was the little hook part of the mount. ...

Print Settings Printer: QIDI X-One2 Rafts: No Supports: No Resolution: 0.3mm Infill: 50% Filament: Sunlu PLA + Notes: The goal here is strong, rigid parts since it is holding a 1kg spool in a cantilever design. At 0.3mm, each part prints in about an...

I designed this spool roller to clip onto my QIDI X-PLUS printer, where it replaces a built-in holder that I found created too much friction, especially when printing with TPU material, which caused frustrating voids. To solve this issue, I opted for...

Qidi X Max microswitch Holder for a more accurate bed Also a holder for measuring gauge. Please look as video on You Tube before downloading. Under Qidi Max Bed levelling. ...One print is for bolt through & the other for tapping 3mm.

I found the two black ABS rings to be a hassle to take off or adjust, so I came up with a clip that keeps the spool of filament centered near the input tube (for the outside filament rack) while still coming off easily for filament replacement.

... thought that it might be useful. ...I have a Qidi Tech 1 and X-Pro, I just tested it on the Tech 1. It fits a 1kg printer spool perfectly, with some slack, so should work with other 1kg Spools. ...You will just need an M10 x 50 bolt, nice and simple.

This is an upgraded version of the Qidi 3D X-Plus Spool Roller, crafted by mistertech, where two critical parts are replaced with a more substantial structure. The original files, Spool_Roller_lock_170mm.stl, which held the assembly together, have...

This mod allows you to attach the spool to the top of a Qidi X-one2 (older version) and switch it from the front. I used the right side handle as the mount and inserted longer screws, making it easy to remove the mod and restore the system to its...

... ...I tested it on my Tech 1 and found that it fits a standard 1kg printer spool snugly, with some extra room to spare, so it should work just as well with other 1kg Spools. ...All you'll need is an M10 x 50 bolt, which is quick and easy to install.

I designed that holder for the X-Max to use bigger spools. ... Should fit on the X-Plus too.

This adapter will enable you to use a filament spool with a [roughly] 3 inch hole on the Qudi Tech X-One2 filament spool holder that came with the printer (which has a [roughly] 2 inch hole).

Simple spacers designed specifically for use with Hatchbox filament on a QIDI X-MAX 3D printer model.