qidi 3d printer x one2

If you don't have it installed in your printer already, you can contact QIDI support and they will send one to you and you can switch it yourself. The new carriage has a fan duct attached by two screws. Once you have installed the new extruder...

If you don't have it installed in your printer already, you can contact QIDI support and they will send one to you and you can switch it yourself. The new carriage has a fan duct attached by two screws. Once you have installed the new extruder...

This is a recessed cover designed to close the large opening in the Qidi X-Max & X-Plus printer top covers, allowing for filament spools to be accommodated without excessive pressure. Additionally, I created a 30mm to 50mm spool insert that helps...

This is a Hygrometer / Thermometer Holder that snaps onto the rear chamber fan cover of the QIDI X-Max and X-Plus. It was requested by one my followers. It might fit other printers as well.BOM - Bill of materialsYou need a small round hygrometer...

Step file is available if you want to make any changes.Be sure level the bed afterwards.Print SettingsPrinter:QIDI Tech X-MaxRafts: NoSupports:NoResolution: 0.15 mmInfill:30 %Filament: Prusament PC Blend Orange  Notes: I...

There are four parts: Upper Guide, Lower Guide, Lower Guide Standoff, and PTFE Tube connector for BMG type extruders.The setup uses about 1.5 meters of PTFE Teflon tubing 4mm ID X 6mm OD 1.5:...

... design a brand new pivot connector that would position the camera in the front, exactly where I needed it. I've got it mounted on my QIDI TECH 1's left side, but it should work just as well on the right side if you prefer to have it there instead.

You can use it internally like I have done here or anywhere you like.Next, load the filament in your extruder and you're done.Print SettingsPrinter:QIDI Tech X-MaxRafts: NoSupports: NoResolution: 0.20 mmInfill: 25% Filament:...

After getting frustrated with every adapter and modification I've tried for my Qidi X-Plus, and X-Max, I have tried most of the prints and only found one mod that works (yet motion isn't as smooth as I'd...

I purchased a dial indicator to level my qidi x-plus more easyly and precisely. When I tried the holder from fdunn59 (https://www.thingiverse.com/thing:4633291) I had the problem, that material from the neodym magnets rest on the linear rails and it...

Print on it's side with support between the feet (as per diagram in "QIDI X-Plus X-Max Ribbon Cable Bracket by humebeam ") Printed in PLA+, has enough flex. Post-printing, just needs sharp edges smoothed. Note: with any back clip, on the X-PLUS,...

To upgrade, you only have to reprint this part, the other parts are unchanged: qidi-xplus-xmax-extruder-fan-duct-404020-part-2-ribbon-cable-holder-1.1.stl About This is an alternative to my QIDI X-Plus X-Max Advanced Extruder Cover:...

Make sure you feed the filament from below the spool through the black filament guide tube.BOM - Bill of Materials2 x 608ZZ roller bearings1 x M3 or M4 screw and bolt (15 mm) (optional, you can use the stock screw and nut)What to printPrint the...

I increased the size of the cable access because my cable would not fit. ...Guessing Qidi may have changed the cable size.

I broke my spool holder so made another and it fits the Qidi perfectlyAlso fits all standard rolls of filament. I used Tree Supports and printed in PLA

About This is an advanced Extruder Cover for the QIDI X-Plus and X-Max. The original cover didn't have much space for a larger fan (although a 40 mm fan just about fits) and was lacking a few other features. The cover has the following features:...

I purchased the Qidi X-Max in December 2021 and these carriages fit models of this period. The bearings are 29mm L, 19mm O.D., 10mm I.D. Probably fits the X-Plus from the same period, but I cannot confirm this. My system was making unsettling...

3:1 BMG Extruder) // New PID values // tested code in Octoprint M303 E0 S220 C10; // returned: bias:105 d:105 Ku: 37.659279 Tu:21.200001 // returned: Kp: 22.595568 Ki:2.131657 Kd:59.878258 // Send updated PID M301 P22.595568 I2.131657 D59.878258; //...

About This is a support bracket for the Qidi X-Plus and X-Max ribbon cable, it attaches to the top extruder cover. Without support, the cable dips down when it gets extended, causing unnecessary stress on the cable as well as it getting greasy from...

About This is a filament cleaner and backspin preventer for the QIDI X-Plus and X-Max. It was originally designed for one of my other designs but I never included it there. To use, print the two parts. Cut a piece of sponge and place it inside the...

The files added are: external-rod-holder-left-tall-1.0.stl external-rod-holder-right-tall-1.0.stl About The Adjustable Spool Holder for QIDI X-Plus and X-Max works with most filament spools up to 1 Kg. It uses common 608 roller bearings (search for...

Print Settings Printer: QIDI Tech Rafts: No Supports: Yes Resolution: 0.12 Infill: 30% Notes: Support used on interior to make sure acrylic mates properly. Printed in ABS with 3 shell layers, 7 top and bottom layers. ...My infill for these parts was...

This is support for inner tube 8 mm of Qidi X-Plus printer.

This is support for inner tube 8 mm of Qidi X-Plus printer.

Print Settings: Printer: QIDI Tech Rafts: It doesn't really matter. Supports: Yes Resolution: 0.12mm Infill: 30% Notes: These parts were printed in ABS with 3 shell layers, 7 top and bottom layers. ...My infill for these parts was set at 30%,...

Print Settings Printer: QIDI Tech Rafts: No Supports: Yes Resolution: 0.12 Infill: 15% Notes: Support used on interior to ensure proper mating of acrylic parts. Printed in ABS with 3 shell layers, 7 top and bottom layers. My infill for these parts...

Required purchase - 40mm x 10mm 24v fan. Some sanding of carriage material also required in order for lower duct scoop to fit between extruder and carriage housing. Quick print. Recommend filament that withstands high temps, Nylon, ASA or...

I bought mine here: https://www.amazon.com/gp/product/B07JG7DS7V/ If they are out of stock the specs are: Inner thread size M3 x 0.5 Outer thread size M5 x 0.5 Length 6mm This is primarily for people who would want to print these parts out in resin...

Made this spool holder extension to be able to mount large spools on the stock spool holder of my X-Plus (i think this should also work with the X-Max). Insert the extensions on top of the fully extended spool holder rods and then place the spool...

This remix is 2 mm taller and close to the original height so you don't have to make any adjustments to the printer firmware, just unscrew the four screws and replace the steel brackets with your printed ones and insert the limit switches. Print one...