qav s mini 3d models
1355076 3d models found related to qav s mini.
thingiverse
Camera mount that fits perfectly on the QAV-S Mini 3". I have printed it in TPU and PLA. ...
thingiverse
Simple SMA Antenna Holder for Lumenier QAV-S MINI 3 Frame.
thingiverse
Simple VTx antenna mount for a SMA connector designed for the QAV-S Mini frame.
thingiverse
Camera mount that fits perfectly on the QAV-S Mini 3". ...I have printed it in TPU and PLA
thingiverse
This is an action cam mount for the QAV-S mini. I couldn't find anything anywhere so I whipped this thing up. Its not perfect. May need to ream out the holes a lil. Hope it can help someone. ...I created this to mount my Runcam Thumb.
thingiverse
front bumper for the fpv crate qav-s mini 3"/4" its a very tight to get on. the bottom screws and the stand-off's hold it on. To mount it you'll have to take off your front stand offs, slide your m2 screw in the bottom, start threading the stand off...
thingiverse
mount for Caddx Peanut for QAV-S MINI 3 frame
thingiverse
Remix of GrowingSurvival's design to make it fit a QAV-S Mini. ...Note that the Immortal T angles downwards to give more clearance from props.
thingiverse
TBS M8.2 GPS mount for the Lumenier QAV-S Mini. ...There is a version for just the GPS and another designed to support a TBS Triumph MMCX VTx antenna.
thingiverse
This is a remix of MacNeill's design of the antenna holder. ...It has been remixed to fit the QAV-S mini. ...Used the Happymodel EP1 TCXO receiver, available here: AliExpress: https://s.click.aliexpress.com/e/_DEHU74j GetFPV: http://bit.ly/3GRtYC8
thingiverse
Part made for Lumenier QAV S MINI 3" (may fit other models) Mounting: 19mm apart for 4mm (M2) standoffs @ 20mm high To increase strength/duribility: - Use higher infill % - Increase Wall and Top/Bottom count (for lighter weight) - Use 0.15 layer...
thingiverse
The Lumenier QAV-S Mini frame is an amazing sub-250 gram frame; however, the stock antenna mount is made out of a very hard TPU that offers no antenna protection and causes the antenna cable itself to take the impact during crashes. This design is...
thingiverse
Remix of my favorite antenna mount, resized to fit the larger DJI O3 air unit antenna on the QAV-S Mini frame. New V2 file uploaded with the antenna having a lower angle. See the comparison picture. ... Check out my install video on YouTube here:...
thingiverse
Finally a vtx/rx antenna holder for the Lumenier QAV-S MINI 3"/4" freestyle quad! designed for a "t" style rx antenna. and a sma style vtx antenna edit 1-29-21: extended version added! depending on your setup you may need more room for your vtx/rx...
thingiverse
Tested on a QAV-S Mini frame. This is a remix of an existing design; however, I cannot find the originally design to give credit. I only take credit for the remix. IMPORTANT: You will need M1.6x10mm screws and need to ensure that your screws...
thingiverse
This is a camera mount for the QAV-S JB Edition for a mini cam. The camera mount delivered with the frame only takes nano cams, and I wanted to use a mini cam. Print it with 100% infill and supports at the little bridge at the end. Depending on...
thingiverse
print on side with support for stronger prints. ... Added thicker areas for screws to compress tpu you may need a washer..
thingiverse
... button, display and led on the GoPro 11 mini when strapped to the drone. ... Print upside down (laying flat) with TPU and bend the flaps down by using a hot air gun at arround 220 Celcius. Use a 20mm battery strap to strap it to the QAV-S foam mount
thingiverse
I have built this holder specifically for the JB QAV-S frame where in the original only a SMA holder is considered. But I also wanted to attach the new GPS module "m100 mini" from HGLRC and therefore this design. I used for printing Filamentum...
thingiverse
Left and right stack protectors for Lumenier QAV-S. ...Print in ABS or PETG. Also look at my QAV-S Skids https://www.thingiverse.com/thing:6121858 QAV-S Caddx Vista Antenna Holder https://www.thingiverse.com/thing:6121848
thingiverse
Arm Skids for Lumenier QAV-S. ...Print in ABS or PETG. Also look at my: QAV-S Stack Protectors https://www.thingiverse.com/thing:6121861 QAV-S Caddx Vista Antenna Holder https://www.thingiverse.com/thing:6121848
thingiverse
A skid to protect the screws on the bottom of the QAV-S frame. ...The holes are designed for 16mm motor mounting NOT 19mm.
thingiverse
QAV-S arm skids, front guard, and wire protectors. Didn't see anything made for this frame that I liked so I decided to make my own. The arm skids mount to the underside of the arms. They are thick enough so the hardware on the underside of the...