q1r quick release 3d models

The assembled model is 175mm tall, 315mm long and is mostly in proportion to my previously released Looney Tunes models. Enjoy! ........................................................................................................... Special...

Replace it with paper (tip: lay the original dial face down and trace around it to make a cutting pattern), or simply clean the adhesive off the dial pan and leave it bare.Alternatively, you could leave the original dial in place and paint it, or...

***You break, modify, breathe on, glance at, or even think about your printer, you're responsible for any consequences*** Initial Release (Beta Test Stage): Xcarriage Back: Xcarriage - Direct Drive Xcarriage blocks Motor Mount v2 Back Idler Y Idler...

Updates ------- • 2022.02.28: Stronger x-axis mount v2 released in both the normal and reinforced variations. • 2022.02.23: Y-axis assembly stablizer added and y-axis mounting holes adjusted for better fitment. • 2022.02.22: Strengthened the...

The LED light fixture assembly can be removed by releasing the hand knob and sliding the light and mounting bracket off of the center support while the legs can be collapsed, aiding in deployment, storage and transport. The lamp can be easily...

You will need something that's 1mm to fit in the hole.v1.2Rail Concept (experimental release):Testing a new concept: A new modular system that uses side mounted "rails" that can be made to fit additional accessories. At the moment I have one that...

Check out this funny result of my 3D model customizer! The 3D Model Customizer for normal space soldiers is already available for all full access patrons and the heavy version will be released next week, so if you also want to customize your 3D...

Such upgrades are welcome as derivatives. ** I initially designed the Scepter when cosplaying as Loki for the Avengers movie release. I decided that every villain needs a weapon and my 3D printer (Replicator Dual, MKI) needed to start earning its...

Changelog: Case (top and bottom) v3 - initial release v4 - slight tweeks to the location of the antenna connector hole and board edge stop for better fit. Compatibility: This case was designed around the Malachite (Chinese clone, version 3) SDR...

Press down on the handle and turn it clockwise (as indicated by the arrow on the top of the Handle) by one half turn.Align the second Blade Carrier Alignment Line with the Alignment line on the Top plate, lift the cutter to the top of its travel...

We created this to use with the Crystal Generator (https://www.thingiverse.com/thing:4842466) we released last week, but this base is perfect for illuminating any small objects from minifigures to jewellery or 3D prints. This design is completely...

After printing/testing multiple versions of other splitter designs (see below) we decided to build a new splitter that: Has uniformly thicker walls. Has shorter branches (less likely to break). Is much faster to print. Doesn't require supports or...

Sketched utilizing AutoCAD 2013 software --- Created in AutoCAD version 2013 --- Designed using the 2013 release of AutoCAD --- Using AutoCAD 2013, this was designed --- This design is based on AutoCAD's 2013 edition --- Involving AutoCAD 2013, the...

See my Thingiverse Profile for the full list of parts kits I’ve released so far. Each of these kits includes combined ships and ship parts STL files, along with blender source files used to create them. Ship files should be ready to print. Part...

Hello, this is Logo of Hockey team Detroit Red Wings created for Multimaterial print. You have two choices   1, You have MMU and you can print it normally with that.2, You don't have MMU but you have time to change filaments...

The keys should respond when pressed and moved back when released. Now use another magnet and test its polarity against the magnet in the phone's body. The magnets should contract each other! Put this magnet in the display magnet pocket. Put display...

Print and install the replacement dial, then reinstall the mechanism, making sure the peg on the front adjustment screw fits into the slot on the front of the mechanism.Alternatively, use flat-bladed screwdrivers to release the eight clips around the...

Make sure they do not get twisted inside the guide as this will increase resistance. Step 8 Insert the rounded hitch into the slot in the base next to the strings and turn it to slide in place. Step 9 Pull on the other side of the guide to spread...

It will also lift this amount, relative to current z height, for every dock/attach move.Variable_attachmove_x: This is the x position needed to clear the retainer and where it lower for the release Variable_dockmove_x: This is how far on the x it...

12/5/20 Revision 4; release candidate 1. Early in the morning on 12/6, I uploaded a replacement barrel for revision 4, to fix the trunnion protruding into the bore. In the afternoon of 12/6, I uploaded a second replacement barrel for revision 4, to...

If you use the caps, apply a little bit of plastic glue/superglue… if you ever need to remove the door without using the magnetic lock, simply use a flat screwdriver and a little tap to remove the caps and after that the steel rod, thus releasing the...

You can adjust the tension a bit by tightening or loosening the screw. UseTo open, or close, just pull slightly, turn, and release.When open, the arm should lock at a 45º angle.There's a little tab on the arm to keep it in place when folded.Tip:...

They can be easily removed with a flat screwdriver, just insert it straight into the tab slot to release. Be careful to not pry, or the tabs might snap!</p><figure class="image image_resized" style="width:50%;"><img...

We are finally releasing some of the STL's for our Mini Thunderbolt 1003 we have been working on for the past few years. I haven't had al the time in the world to work on this so it's not perfect but it works. I have attached a bunch of different...

Tighten it just enough to take out any slop while keeping it loose enough that the Button spins freely and snaps back to center when released.Attach to 2020 Extrusion with M4 bolts and T-Nuts through holes at the bottom of the Extrusion Mount.Connect...

The lid snaps into place.&nbsp;To release the lid, squeeze the tabs on the side of the lid and lift it off. The lid can be snapped onto the bottom of the game to keep it safe during play.</td><td colspan="2"><figure class="image"><img...

It's still being designed, (It'll be released mid to late 2021. This is being written in Feb 2021.) but it will probably have a backwards compatible camera mount, like the Vive Tracker. But the real potential will be to remove the camera mount and...

After that, the plastic will often release the tissue, letting it fall back into the box. Then you have to jam your hand through the plastic and fish around to get the next tissue out. The act of groping around widens the hole in the plastic, and the...

After picking up and dropping the project several times, I am very glad to finally be releasing it and getting it off my workbench and mind.My goal was to make the kit simple and inexpensive, so no matter what someone's modding skill set or budget...

Summary This is an update design to the 1st version of this released in 09/2020, https://www.thingiverse.com/thing:4605853. Most of the parts between the 2 builds are interchangeable. There are no tapped holes needed with this build & it is a more...