puzzle cube maker 3d models

If you have the proper filament colors, no painting is needed.The assembled model is 190mm tall.Enjoy!...........................................................................................................Special shoutout to maker Benoît Lussier...

Those two parts are also included without supports for those makers who prefer to use supports via their slicer. If you have the proper filament colors, no painting is needed. The assembled model is 230mm tall. Enjoy Note: the built-in supports...

The magic e-step number for me was 107; I experimented and found that Bulldog makers recommend this setting, which worked great. There's no under/over extrusion, and any wacky spots are well within the feed rate override (I haven't touched it and...

Mine is installed on the I3V 10" printer, but it should work with many Maker Farm kits. You'll need to print four side supports, two flanges, and two motor mounts. Required hardware includes: - Lead Screw (I used this one -...

To score a transparency sheet on the Cricut Maker, use the perforation wheel and tell it that it's light cardboard. Cut as usual with the fine point blade. Adjust pressure according to your material. I used basic overhead ink jet printable...

Hi MTB friends!Every owner of a mountain bike probably knows the problem: The stable mounting of mudguards is really difficult, because the manufacturers of the bike have not provided a solution for it.Fortunately, we are Maker so take measurements,...

Special shoutout to maker Benoît Lussier for providing QA printing and quality feedback. ........................................................................................................... **Print Instructions:**Supports: ear_right, ear_left,...

But these are small problems that a "maker" is certainly able to solve quickly and with little expense, something different is the chronic loss of synchronism of the two screws that operate the Z axis controlled by two separate steppers. Initially...

Amateur Telescope Maker's Smartphone Tester Based on Don Peckham's iPhone Ronchi Tester, this device is designed to perfectly fit a Google LG Nexus 5X smartphone. The photos show my cardboard and hot glue mock-up (functional but not aesthetically...

... to apply it safely. 5. I share this system with the community of makers for free and I hope you’ll appreciate it. ...Be aware though that it’s your sole responsibility of anything may happen when you decide to use this system in your printer.

This Challenge pushed us makers to create something remarkable - a place or famous thing on this planet. The thing I decided to model for the Challenge is not just a famous location to visit in the world. While it is a world-famous landmark, It is...

 I'm hoping some makers will produce one or more appropriate signs and post them as remixes...Assembly tips:1 - Take your time gluing the model together and enjoy the process.2 - I used E6000 sticky craft glue to put this model together. The...

by Zenmaster_Maker http://www.thingiverse.com/thing:3345859 Banthas (Star Wars Legion scale) by McAnultyMiniatures https://www.thingiverse.com/thing:3958418 Re-sculpted Star Wars Dewback by DaylightInventor https://www.thingiverse.com/thing:2856774...

Video link here; https://youtu.be/xta0gl2TDL0 UPDATE 2/25/21 - Update to instructions - found by a maker - You need 2 fan ducts - One for the left side and one for the right. You need to mirror the fan duct to print the second one, so that it is...

Older version files are in a zip file to download if needed.Makers Check out @streetmaker and @memisis who printed this out in some great colors! The real life photos are from their makes of the solder station.Streetmaker:...

I just like to cover all bases due to the different skill sets of makers) Print instructionsRafts: Doesn't Matter Supports: No Resolution: .2mm Infill: 10% Notes:** Refer to the notes below for helpful printing and assembly instructions Building...

...........................................................................................................Special shoutout to maker Benoît Lussier for providing invaluable QA printing and quality feedback. Another shoutout to the guys at 3DBoom...

UPDATE 3 (regarding Wanhao Duplicator i3/i3Plus):\nI highly recommend replacing the bearing rods and generously applying MoS2 grease to the inside radius of the original linear ball bearings for maximum quietness and lower friction.\nThe greased...

Steps to tap the shaft of the stepper motor: Imobilize the axle with the tool used to secure the thread maker (which means you may need another one); Drill a hole 2.5 mm diameter 10 mm deep into the shaft; Form the thread with a 3 steps M3 forming...

Youtube videos: nABLE at the Rochester Mini Maker Faire https://youtu.be/YRXA0slO2vM Assembling the Explorer Thumb TD https://www.youtube.com/watch?v=BRuFUtK4K90&feature=youtu.be Adding a frictional surface to the Explorer Thumb TD...

What makers need is a totally new and novel 3D printable bearing means which can be really useful. Here is a new design by fractalgears.co for use in all of your personal design projects. The gearing system is versatile, highly efficient, and easy to...

Also, **please follow us on Thingiverse and give this a like if this came in handy **and for more information on this project, please visit us at http://www.DIY3DTech.com as well as subscribe to our YouTube Channel at http://YouTube.DIY3DTech.com...

Special shoutout to maker Benoît Lussier for providing QA printing and quality feedback. Another shoutout to the guys at 3DBoom (Thingiverse id: 3db00m) for printing a final proof copy of this model. A picture of the front view of their print is...

You may need to change slicer options (like flow or horizontal expansion) for this model if it will be too lose or to hard to put it WARNING: NOT FOR SMALL KIDS Small parts and some not as strong to be kid-proof Printed on JG Maker A1 (JG Aurora A1)...

In 1967, readers of Melody Maker voted him the Pop Musician of the Year and in 1968, Billboard named him the Artist of the Year and Rolling Stone declared him the Performer of the Year. Disc and Music Echo honored him with the World Top Musician of...

Special shoutout to maker Benoît Lussier for providing QA printing and quality feedback. Another shoutout to Jarvis Henderson (Printables id: biggdog55) for suggesting the speed limit sign accessory. Print Instructions: Supports: No Resolution:...

In line with selecting the most effective optical solution: Fisheye lens technology from renowned optics maker Samyang proved its capabilities through offering up a full spectrum viewing capability within this Northern Light capture, thereby...

To support Makers and open source initiatives, every bit of data in this Project can easily be customised with open source programs (Thonny, ArduinoIDE, FreeCAD) or at least free programs (easyEDA) to make your own remix. This design is made as a...

Dont order parts upfront if your unsure the files can be printed with your printer.And with that out of the way lets get back to the project._________________________________FEATURES: Rugged case with TPU bumpers12" Full HD IPS Panel ( low power...

Provided your a well trained maker, this still can be done freehanded, but use a 4.5mm driller before you go straight to 5mm. -the whole rest is simple and straight forward. The main housing... It something you probably cannot use the way I did it,...